PbS and CdS Quantum Dot‐Sensitized Solid‐State Solar Cells: “Old Concepts,New Results”

Lead sulfide (PbS) and cadmium sulfide (CdS) quantum dots (QDs) are prepared over mesoporous TiO₂ films by a successive ionic layer adsorption and reaction (SILAR) process. These QDs are exploited as a sensitizer in solid‐state solar cells with 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) as a hole conductor. High‐resolution transmission electron microscopy (TEM) images reveal that PbS QDs of around 3 nm in size are distributed homogeneously over the TiO₂ surface and are well separated from each other if prepared under common SILAR deposition conditions. The pore size of the TiO₂ films and the deposition medium are found to be very critical in determining the overall performance of the solid‐state QD cells. By incorporating promising inorganic QDs (PbS) and an organic hole conductor spiro‐OMeTAD into the solid‐state cells, it is possible to attain an efficiency of over 1% for PbS‐sensitized solid‐state cells after some optimizations. The optimized deposition cycle of the SILAR process for PbS QDs has also been confirmed by transient spectroscopic studies on the hole generation of spiro‐OMeTAD. In addition, it is established that the PbS QD layer plays a role in mediating the interfacial recombination between the spiro‐OMeTAD⁺ cation and the TiO₂ conduction band electron, and that the lifetime of these species can change by around 2 orders of magnitude by varying the number of SILAR cycles used. When a near infrared (NIR)‐absorbing zinc carboxyphthalocyanine dye (TT1) is added on top of the PbS‐sensitized electrode to obtain a panchromatic response, two signals from each component are observed, which results in an improved efficiency. In particular, when a CdS‐sensitized electrode is first prepared, and then co‐sensitized with a squarine dye (SQ1), the resulting color change is clearly an addition of each component and the overall efficiencies are also added in a more synergistic way than those in PbS/TT1‐modified cells because of favorable charge‐transfer energetics.     

An optimal inspection policy for a storage system with high reliability

A system such as missiles and spare parts of aircrafts has to perform a normal operation at any time when it is used. However, a system is in storage for a long time from the transportation to the usage and its reliability goes down with time. Such a system should be inspected and maintained at periodic times to hold a higher reliability than a prespecified value q. This paper suggests a periodic inspection of a storage system with two kinds of units where unit 1 is inspected and maintained at each inspection, however, unit 2 is not done. The system is replaced at detection of failure or at time when the reliability is below q. The total expected cost until replacement is derived and an optimal inspection time which minimizes it is discussed. Numerical examples are given when failure time distributions are exponential and Weibull ones.     

Estimation of thermal parameters of the enclosed electronic package system by using dynamic thermal response

A methodology for modeling and simulating the electro-thermal behavior of an enclosed electronic package is presented and validated. The electro-thermal model is constructed using system dynamics. The system model, in which the electrical and the thermal domain are combined, is presented. The developed model describes the dynamic thermal behavior system that was an electronic device in the test enclosure. An effective way to identify the thermal parameters of the system, especially the thermal contact resistance, is suggested. In detail, the new method for thermal resistance identification is based on the temperature difference behavior between the component and the air temperature inside the enclosure. Based on the proposed model, either the variation of the heat source or the ambient temperature can be estimated. Simulated results were in good agreement with the measured temperature in the transient state accompanying with the variation of the environment.     

Robust porous SiOCH/Cu interconnects with ultrathin sidewall protection liners

Robust porous low-k/Cu interconnects have been developed for 65-nm-node ultralarge-scale integrations (ULSIs) with 180-nm/200-nm pitched lines and 100-nm diameter vias in a single damascene architecture. A porous plasma-enhanced chemical vapor deposition (PECVD)-SiOCH film (k=2.6) with subnanometer pores is introduced into the intermetal dielectrics on the interlayer dielectrics of a rigid PECVD-SiOCH film (k=2.9). This porous-on-rigid hybrid SiOCH structure achieves a 35% reduction in interline capacitance per grid in the 65-nm-node interconnect compared to that in a 90-nm-node interconnect with a fully rigid SiOCH. A via resistance of 9.7 /spl Omega/ was obtained in 100-nm diameter vias. Interconnect reliability, such as electromigration, and stress-induced voiding were retained with interface modification technologies. One of the key breakthroughs was a special liner technique to maintain dielectric reliability between the narrow-pitched lines. The porous surface on the trench-etched sidewall was covered with an ultrathin plasma-polymerized benzocyclobuten liner (k=2.7), thus enhancing interline time-dependent dielectric breakdown reliability. The introduction of a porous material and the control of the sidewall are essential for 65-nm-node and beyond scaled-down ULSIs to ensure high levels of reliability.     

Stability of Skutterudite Thermoelectric Materials

By multifilling with La, Ba, Ga, Ti, Yb, Ca, Al, and In, the dimensionless figure of merit ZT of filled skutterudites has been improved in this work. ZT reached 0.75 for p-type (La,Ba,Ga,Ti) _x (Fe,Co)₄Sb₁₂ (x = 0.8 to 1.0) and 1.0 for n-type (Yb,Ca,Al,Ga,In) _y (Co,Fe)₄Sb₁₂ (y = 0.7 to 0.9). After annealing at 873 K for 180 h, 300 h, 710 h, 1000 h, and 5000 h in vacuum, the Seebeck coefficient S and the electrical resistivity ρ of the samples increased while the thermal conductivity λ decreased with increasing annealing time. As a result, the ZT values of both p- and n-type skutterudites remained unchanged or were slightly improved, demonstrating the excellent thermal stability of these skutterudites.     

An Organoid for Woven Bone

Bone formation (osteogenesis) is a complex process in which cellular differentiation and the generation of a mineralized organic matrix are synchronized to produce a hybrid hierarchical architecture. To study the mechanisms of osteogenesis in health and disease, there is a great need for functional model systems that capture in parallel, both cellular and matrix formation processes. Stem cell-based organoids are promising as functional, self-organizing 3D in vitro models for studying the physiology and pathology of various tissues. However, for human bone, no such functional model system is yet available. This study reports the in vitro differentiation of human bone marrow stromal cells into a functional 3D self-organizing co-culture of osteoblasts and osteocytes, creating an organoid for early stage bone (woven bone) formation. It demonstrates the formation of an organoid where osteocytes are embedded within the collagen matrix that is produced by the osteoblasts and mineralized under biological control. Alike in in vivo osteocytes, the embedded osteocytes show network formation and communication via expression of sclerostin. The current system forms the most complete 3D living in vitro model system to investigate osteogenesis, both in physiological and pathological situations, as well as under the influence of external triggers (mechanical stimulation, drug administration).     

Dynamic properties of an all solid-state frequency-shifted feedbacklaser

Frequency-shifted feedback (FSF) laser exhibits outstanding features in its oscillation spectrum. We analyze build-up dynamic properties of the FSF laser by means of rate equation and analyze steady-state dynamic properties of the FSF laser by means of Wigner-Ville distribution of intracavity electric field. Furthermore, we analyze instantaneous oscillation frequency at peak spectral intensity and oscillation bandwidth of its spectrum using the formula of instantaneous spectral intensity derived from Wigner-Ville distribution of intracavity electric field. These analytical results are in good agreement with the experimental ones which have been observed by a diode-pumped Nd:YVO₄ FSF laser. It becomes clear that the FSF laser supports many frequency components simultaneously even though the gain medium is homogeneously broadened and has a continuously chirped frequency components of comb in which the creation of chirped frequency components are strongly correlated in phase because of a replica of the preceding components. Also, the instantaneous oscillation frequency is closely related to the detuning frequency which depends on the total net gain in the cavity and the gain bandwidth of atomic transition. The oscillation bandwidth is defined as the product of the saturation-broadened bandwidth and the total resonant modes contributing to FSF operation     

Bidirectional finite-element method-of-line beam propagation method(FE-MoL-BPM) for analyzing optical waveguides with discontinuities

A bidirectional finite-element method-of-line beam propagation method (FE-MoL-BPM) is newly proposed for analyzing optical waveguides with discontinuities including transmissions, reflections and radiations. In this approach, the finite-element method (FEM) is introduced to discretize the derivatives of the variable perpendicular to the propagation direction. Since the proposed method is accurate and stable, only a small number of nodal points are required