Fuel cell-battery hybrid powered light electric vehicle (golf cart): Influence of fuel cell on the driving performance

A light electric vehicle (golf cart, 5 kW nominal motor power) was integrated with a commercial 1.2 kW PEM fuel cell system, and fuelled by compressed hydrogen (two composite cylinders, 6.8 L/300 bar each). Comparative driving tests in the battery and hybrid (battery + fuel cell) powering modes were performed. The introduction of the fuel cell was shown to result in extending the driving range by 63–110%, when the amount of the stored H₂ fuel varied within 55–100% of the maximum capacity. The operation in the hybrid mode resulted in more stable driving performances, as well as in the increase of the total energy both withdrawn by the vehicle and returned to the vehicle battery during the driving. Statistical analysis of the power patterns taken during the driving in the battery and hybrid-powering modes showed that the latter provided stable operation in a wider power range, including higher frequency and higher average values of the peak power.     

Numerical Evaluation of Flow and Heat Transfer in Plate-Pin Fin Heat Sinks with Various Pin Cross-Sections

A numerical investigation of the thermal and hydraulic performance of 20 different plate-pin fin heat sinks with various shapes of pin cross-sections (square, circular, elliptic, NACA profile, and dropform) and different ratios of pin widths to plate fin spacing (0.3, 0.4, 0.5, and 0.6) was performed. Finite volume method-based CFD software, Ansys CFX, was used as the 3-D Reynolds-averaged Navier-Stokes Solver. A k-ω based shear-stress-transport model was used to predict the turbulent flow and heat transfer through the heat sink channels. The present study provides original information about the performance of this new type of compound heat sink.     

Ultrasonic spray pyrolysis of surface modified TiO2 nanoparticles with dopamine

Spherical, submicronic TiO₂ powder particles were prepared in the low temperature process of ultrasonic spray pyrolysis (150 °C) by using as a precursor aqueous colloidal solutions consisting of surface modified 45 Å TiO₂ nanoparticles with dopamine. Detailed structural and morphological characterization of colored submicronic TiO₂ spheres was performed by X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), laser particle size analysis and FTIR techniques. Also, optical characterization of both dopamine-modified TiO₂ precursor nanoparticles and submicronic TiO₂ powder particles was performed using absorption and diffuse reflectance spectroscopy, respectively. A significant decrease of the effective band gap (1.9 eV) in dopamine-modified TiO₂ nanoparticles compared to the band gap of bulk material (3.2 eV) was preserved after formation of submicronic TiO₂ powder particles in the process of ultrasonic spray pyrolysis under mild experimental conditions. Due to the nanostructured nature, surface-modified assemblage of TiO₂ nanoparticles preserved unique ability to absorb light through charge transfer complex by photoexcitation of the ligand-to-TiO₂ band, conventionally associated with extremely small TiO₂ nanoparticles (d < 20 nm) whose surface Ti atoms, owing to the large curvature, have penta-coordinate geometry.     

Development and In Vitro Characterization of Chitosan-based Microspheres for Nasal Delivery of Promethazine

ABSTRACT

Conventional and composed promethazine-loaded microspheres were prepared by spray drying of chitosan solution systems and double water-in-oil-in-water (W/O/W) emulsion systems, respectively. Double emulsions were prepared in two different feed concentrations, with chitosan dissolved in both water phases, and ethylcellulose dissolved in oil phase. Swelling and bioadhesive properties of the microspheres depended on the chitosan content, type and the feed concentration of spray-dried system. Results obtained suggested that better ethylcellulose microcapsules with promethazine in the chitosan matrix were formed when less concentrated emulsion systems were spray-dried. Thus, in case of such a system, with ethylcellulose/chitosan weight ratio of 1:2, prolonged promethazine release was obtained.     

Functional Specialization within the EXO70 Gene Family in Arabidopsis

Localized delivery of plasma-membrane and cell-wall components is a crucial process for plant cell growth. One of the regulators of secretory-vesicle targeting is the exocyst tethering complex. The exocyst mediates first interaction between transport vesicles and the target membrane before their fusion is performed by SNARE proteins. In land plants, genes encoding the EXO70 exocyst subunit underwent an extreme proliferation with 23 paralogs present in the Arabidopsis (Arabidopsis thaliana) genome. These paralogs often acquired specialized functions during evolution. Here, we analyzed functional divergence of selected EXO70 paralogs in Arabidopsis. Performing a systematic cross-complementation analysis of exo70a1 and exo70b1 mutants, we found that EXO70A1 was functionally substituted only by its closest paralog, EXO70A2. In contrast, none of the EXO70 isoforms tested were able to substitute EXO70B1, including its closest relative, EXO70B2, pointing to a unique function of this isoform. The presented results document a high degree of functional specialization within the EXO70 gene family in land plants.     

Underwater Acoustic Multimedia Communication Based on MIMO–OFDM

A transmission scheme is proposed based on multi-input multi-output orthogonal frequency-division multiplexing (OFDM) for underwater acoustic multimedia (UWAM) communication. The proposed scheme integrates direct mapping and space-time block code strategies, a power assignment mechanism, OFDM, adaptive modulation, and unequal error protection in a UWAM system. The proposed UWAM system employs high power, low speed modulation, with schemes providing significant error protection for transmission of sensor data messages requiring a stringent bit-error rate (BER). In contrast, low power, high speed modulation schemes with reduced error protection are provided for messages that can tolerate a high BER, such as image and audio signals. Simulation results show that the proposed scheme not only fulfils the quality of services requirements of a UWAM system, but also maximizes transmission bit rates or minimizes transmission power requirements.     

腐植酸的体外作用

腐植酸被认为在动物喂饲试验中对健康和产率具有整体积极作用,同时颇有争议的是,其也被作为肿瘤的病原学因素之一。我们尝试评价斯洛伐克地区特定来源腐植酸在使用推荐预防剂量时的体外作用。研究其体外的抗氧化性质、对肝线粒体中酶系和非酶系抗氧化防御系统的作用以及对人工培养肿瘤细胞株的作用。我们观察到不论腐植酸是溶解于二甲基亚砜(DMSO)或是直接加入呼吸介质中线粒体悬浮液,在腐植酸给药后超氧化物歧化酶(SOD)活性显著下降。所测定的其他抗氧化酶如谷胱甘肽过氧化物酶(GPx)和谷胱甘肽还原酶(GR),其活性及还原型谷胱甘肽(GSH)的含量与对照组相比并未表现出显著变化。腐植酸对超氧阴离子自由基(O2-·)的抑制率低于其对羟自由基(·OH)的抑制率。6种不同肿瘤细胞株的存活率显示出只有急性T淋巴性白血病细胞株对测试腐植酸敏感。尽管在水溶液中溶解度相对较低,但特定来源腐植酸参与了氧化还原调控。通过夺取自由基,腐植酸重置了抗氧化防御机制。来源于自然资源的腐植酸体外研究结果显示出其作为有前景的免疫增强剂的潜力。     

Potassium–Sodium Niobate‐Based Lead‐Free Piezoelectric Ceramic Coatings by Thermal Spray Process

Potassium–sodium niobate (KNN)‐based piezoelectric ceramic coatings with single perovskite phase and dense morphology were obtained by thermal spray processing. The structure, morphology, and properties of the coatings deposited at different conditions were investigated, and excellent piezoelectric performance properties were demonstrated. The piezoelectric coefficient observed in the KNN‐based coatings in this study is about one order of magnitude higher than other thermal sprayed lead‐free piezoelectric coatings as reported in literature. With analyses on the differences in the characteristics between KNN and lead zirconate titanate (PZT) compositions and the reaction mechanisms of thermal spray and ceramic synthesis, the reasons for the successful formation of single‐phase perovskite structure with high crystallinity in the thermal sprayed KNN‐based coatings while not in PZT are explained.     

ANFIS-Based Prediction of the Decomposition of Sodium Aluminate Solutions in the Bayer Process

This article presents the results of nonlinear statistical modeling of the decomposition process of sodium aluminate solution, as part of the Bayer technology for the production of alumina. Based on the data collected in 2011 and 2012 from industrial production in the Bira? Alumina Factory, Zvornik (Bosnia and Herzegovina), nonlinear statistical modeling of the industrial processes was derived. The model was developed as an attempt to define the dependence of the degree of decomposition of sodium aluminate solution as a function of the input parameters of the leaching process: caustic ratio (α_k) of the solution; ratio of the crystallization; content of Na₂O_(caustic) in the solution; the initial temperature of the solution; the final temperature of the solution; average diameter of the crystallized seeds; and duration of the crystallization process. As a tool for statistical modeling, Adaptive Network Based Fuzzy Inference System (ANFIS) was applied. The defined model using ANFIS methodology expressed a high level of fitting, and could be used to effectively predict the degree of decomposition of the sodium aluminate solution as a function of the input process under industrial conditions.     

Mechanical and rheological properties of silica-reinforced polypropylene/m-EPR blends

Rheological and mechanical properties (tensile and impact properties) as well as the mechanical profiles of ternary isotactic polypropylene/silica/elastomer (iPP/SiO₂/m-EPR metallocene catalyzed ethylene-propylene rubber) composites were investigated and discussed. The effects of two metallocene ethylene-propylene-based elastomers (m-EPR) differing in molecular weight/viscosity and their content on iPP/silica composites with different silica types differing in size (nano- vs. micro-) and surface properties (untreated vs. treated) were investigated. The two m-EPR elastomers were added to iPP/SiO₂ 96/4 composites as possible impact modifier and compatibilizer at the same time in 5, 10, 15, and 20 vol% per hundred volume parts of composites. The effects of different silica fillers and two m-EPR rubbers were discussed within the context of structure-morphology-mechanical property relationships of these iPP/SiO₂/m-EPR composites. Tensile and impact strength properties were mainly influenced by combined competetive effects of stiff filler and tough m-EPR elastomer so sinergistic effect was also observed. The ductility of these composites was affected additionally by spherulite size of the iPP matrix due to the difference in nucleation abilities of silica fillers enabled by prevailing separated morphology observed in iPP/SiO₂/m-EPR composites.