An investigation of sugar extraction methods and the use of microwave power for date syrup processing: efficiency and color related considerations.

This study investigates the effect of extraction methods on the color of date syrup and the potential use of microwave power for syrup processing. Sugar solutions were extracted from dates by boiling, soaking and blending. Color and sugar content of the extracted solutions were measured, and the percentage of sugar extracted form the total fruit sugar determined. Boiling was found to be the most efficient method of extraction whereby 74% of total samples sugar was extracted. In contrast, only 54.2% of fruit sugar was extracted by blending and 42% by soaking. In addition, solutions extracted by soaking and blending had a foaming problem in the subsequent concentration process. The extraction method had no effect on the product final color. The extracted solution was concentrated using two heating methods: conventional and microwave heating at a 600 W capacity and a frequency of 2450 MHz applied at three power levels: 10, 7, and 6. In the heating process, 180 minutes were needed to achieve a 77% degrees Brix using convective heating, while it took 81, 138, and 166 minutes of microwave heating at power level 10, 7, and 6, respectively to achieve the same concentration. Water activity of the syrup was measured within a sugar content range of 50 to 80% degrees Brix and the sugar concentration at which the product is shelf stable was determined at 76%.     

Non-equilibrium particle motion in the vicinity of a single blade

The motion of sand particles close to a single moving blade was investigated using Positron Emission Particle Tracking (PEPT) during the period in which the free bed surface profile was evolving to an equilibrium shape. The area affected by the blade was divided into active and inactive regions and these were analysed separately. The characteristic heart-shape of the active region in the plan view was determined. An approximately 10-particle-diameter wide velocity transition zone is found between the two regions. While the tracer particle is in the inactive region moving away from the blade, the time dependence of the axial displacement is well described by a logarithmic relationship. The probability of particle movement towards the centre of the blade was quantified using a “central tendency” index. The calculated central tendency shows maxima at each side of the blade. The separation of the two maxima, which indicates the width of the active region, increases with fill level but is independent of rotational speed.     

Techniques for microstructural characterization of powder-processed nickel-based superalloys

Methods are described for sample preparation of polycrystalline Ni-based superalloys in order to perform a detailed microstructural characterization. Specific techniques for the precise definition of the various phases present are outlined and these are shown to be useful for the measurement of size, volume fractions and distribution. A number of optical, scanning and transmission microscopy techniques are used to provide the necessary information.     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

16信道0.35μmCMOS/VCSEL光发射模块

研究了垂直腔面发射激光器 (VCSEL)及其列阵器件的光谱特性、调制特性、高频特性及与微电子电路的兼容性 ,将 1× 16的VCSEL与CMOS专用集成电路进行多芯片组装 (MCM ) ,混合集成为 16信道VCSEL光发射功能模块 .测试过程中 ,功能模块的光电特性及其均匀性良好 ,测量的 - 3dB频带宽度大于 2GHz.     

Effect of the oxide support on the propane ammoxidation with Sb–V–O-based catalysts

The role of Nb₂O₅ and γ-Al₂O₃ oxide supports on the ammoxidation of propane on supported mixed Sb–V oxide at different Sb+V surface coverages is studied. Sb and V oxide species on alumina and on niobia support show different structural features that reflect in different performance during the ammoxidation of propane to acrylonitrile. Niobia-supported catalysts are much more selective to acrylonitrile than alumina-supported ones. Alumina interacts weakly with the supported oxides while niobia forms new phases through solid state reactions with the supported oxides during catalytic operation that must account for its higher selectivity values towards acrylonitrile and higher specific rate of acrylonitrile formation per vanadium site.     

An investigation into the effect of various chemical and physical treatments of a South African phosphogypsum to render it suitable as a set retarder for cement

The work describes various physical and chemical treatments to eliminate the deleterious effects of impurities in phosphogypsum on the delayed setting time and impaired strength development behaviour of cement to which it was added as a set regulator. The physical treatments included washing, milling, and ultrasonic treatment of the material, while the chemical treatments dealt with acidic and basic additions to the phosphogypsum during the washing stage. It was found that chemical treatment with a milk of lime solution, which is often recommended in literature, was ineffective in reducing set retardation. Treatment with ammonium hydroxide or sulphuric acid was more effective in this regard. Intergrinding phosphogypsum with slaked lime improved its effectiveness in reducing set retardation, but the use of unslaked lime was less effective and also resulted in marked reductions in compressive strengths. A combined treatment of wet milling phosphogypsum with a lime slurry in a ball mall was derived from these experiments and is recommended for full-scale plant applications.     

Tuning the Dimensions of C60‐Based Needlelike Crystals in Blended Thin Films

A new ordered structure of the C₆₀ derivative PCBM ([6‐6]‐phenyl C₆₁‐butyric acid methyl ester) is obtained in thin films based on the blend PCBM:regioregular P3HT (poly(3‐hexylthiophene)). Rapid formation of needlelike crystalline PCBM structures of a few micrometers up to 100 μm in size is demonstrated by submitting the blended thin films to an appropriate thermal treatment. These structures can grow out to a 2D network of PCBM needles and, in specific cases, to spectacular PCBM fans. Key parameters to tune the dimensions and spatial distribution of the PCBM needles are blend ratio and annealing conditions. The as‐obtained blended films and crystals are probed using atomic force microscopy, transmission electron microscopy, selected area electron diffraction, optical microscopy, and confocal fluorescence microscopy. Based on the analytical results, the growth mechanism of the PCBM structures within the film is described in terms of diffusion of PCBM towards the PCBM crystals, leaving highly crystalline P3HT behind in the surrounding matrix.