Nonlinearity analysis and optimization of HBTs for optical mixer designs

Two types of photo heterojunction bipolar transistor (HBT) to directly down-convert optical signals to electronic signals have been reported in the literature: a conventional photo-HBT in which light penetrates through the area of the base-collector junction and an HBT where light shines through the base-collector edge for higher conversion efficiency. Although the performance in relation to bias conditions has been published, the detailed analyses for identifying the parameters and bias conditions that provide optimum direct down-conversion have not been examined. This paper provides a full explanation of the operation of the down-conversion for both HBT configurations based on low-frequency analyses. Such information is useful for both understanding the nonlinear mechanisms involved and designing for maximum efficiency. In addition, a new circuit has been developed from the basic HBT down-conversion circuit that provides improved performance.     

Radiometric sensor for temperature control of food processing

This paper describes a novel planar antenna sensor created for the purpose of noninvasive temperature measurements using microwave radiometry. In order to improve radiometric measurements in industrial applications, a new generation of sensors is introduced, composed of a metallic sheet. Simulations based upon the method of moments is used both to design and to determine their electromagnetic performances. This paper also describes a radiometric device using these sensors to measure and control the temperature of food products during deep freezing processes. The results and discussions are presented.     

Mass Transfer in a Flat Gas/Liquid Interface using non‐Newtonian Media

Gas/liquid mass transfer has been investigated using a stirred vessel gas/liquid contactor using non‐Newtonian media and carbon dioxide as absorbent and gas phase, respectively. The volumetric mass transfer coefficients at different operational variables have been determined. Non‐Newtonian media (liquid phase) were prepared as aqueous solutions of sodium carboxymethyl cellulose salt. The influence of the rheological properties, polymer concentration, stirring rate, and gas flow rate on mass transfer was studied for these liquid phases. Kinematic viscosity and density experimental data were used to calculate the average molecular weight corresponding to the polymer employed. The Ostwald model has been used to fit the rheological behavior of aqueous solutions of the polymer employed as absorbent phase. Reasonably good agreement was found between the predictions of the proposed models and the experimental data of mass transfer coefficients.     

Optimal mean-square prediction of the mobile-radio fading envelope

Long-range prediction of the mobile-radio fading envelope is an enabling technology for many fading compensation approaches. Because the fading envelope is well modeled as a bandlimited process, it has special predictability properties. In this paper, we find a linear predictor that is optimal in the mean-square sense when the predictor impulse response is energy constrained. This solution may be used to determine the minimum mean squared error of a prediction based on past values that are corrupted with estimation errors.     

A new mobile robot control approach via fusion of control signals.

This paper proposes an alternative approach to address the problem of coordinating behaviors in mobile robot navigation: fusion of control signals. Such approach is based on a set of two decentralized information filters, which accomplish the data fusion involved. Besides these two fusion engines, control architectures designed according to this approach also embed a set of different controllers that generate reference signals for the robot linear and angular speeds. Such signals are delivered to the two decentralized information filters, which estimate suitable overall reference signals for the robot linear and angular speeds, respectively. Thus, the background for designing such control architectures is provided by the nonlinear systems theory, which makes this approach different from any other yet proposed. This background also allows checking control architectures designed according to the proposed approach for stability. Such analysis is carried out in the paper, and shows that the robot always reaches its final destination, in spite of either obstacles along its path or the environment layout. As an example, a control architecture is designed to guide a mobile robot in an experiment, whose results allows checking the good performance of the control architecture and validating the design approach proposed as well.     

PNNI-based control plane for automatically switched optical networks

Much effort has been spent on the definition of control plane protocols for automatically switched optical networks (ASON). Most of the proposals brought into the standardization for an International Telecommunications Union-Telecommunication Sector, Internet Engineering Task Force, and Optical Internetworking Forum are based on Internet protocol concepts. One such proposal is the generalized multi-protocol label switching (GMPLS), an extension of the MPLS traffic engineering control plane model that includes nonpacket switched technologies (time, wavelength, and fiber switching). Recently, the potential use of private network-network interface (PNNI) in ASONs has been discussed as an alternative proposal by the standardization bodies. The goal of this paper is to appropriately adapt asynchronous transfer mode into an optical PNNI (O-PNNI) protocol that can be used as the control plane of ASONs. The paper also provides a critical viewpoint on the potential usage of either O-PNNI or GMPLS control plane and analyzes the pros and cons of each. The methodology adopted toward devising O-PNNI hinges on reviewing PNNI along with ASON recommendations in order to determine the set of PNNI features that require adaptation. Having identified these features we engineer and present appropriate solutions relating to routing, signaling and addressing aspects.     

Experimental real-time detector of GSM terminals

The authors present an experimental real-time GSM terminal detector, to be installed in a restricted area. The detector triggers terminal signaling, which can be captured.     

Exposed Die-Top Encapsulation Molding for an Improved High- Performance Flip Chip BGA Package

The recent advancement in high- performance semiconductor packages has been driven by the need for higher pin count and superior heat dissipation. A one-piece cavity lid flip chip ball grid array (BGA) package with high pin count and targeted reliability has emerged as a popular choice. The flip chip technology can accommodate an I/O count of more than five hundreds500, and the die junction temperature can be reduced to a minimum level by a metal heat spreader attachment. None the less, greater expectations on these high-performance packages arose such as better substrate real estate utilization for multiple chips, ease in handling for thinner core substrates, and improved board- level solder joint reliability. A new design of the flip chip BGA package has been looked into for meeting such requirements. By encapsulating the flip chip with molding compound leaving the die top exposed, a planar top surface can be formed. A, and a flat lid can then be mounted on the planar mold/die top surface. In this manner the direct interaction of the metal lid with the substrate can be removed. The new package is thus less rigid under thermal loading and solder joint reliability enhancement is expected. This paper discusses the process development of the new package and its advantages for improved solder joint fatigue life, and being a multichip package and thin core substrate options. Finite-element simulations have been employed for the study of its structural integrity, thermal, and electrical performances. Detailed package and board-level reliability test results will also be reported     

Parametric effects on the transient Voltage performance of a DC superconducting cable

The objective of this work was to determine the significant parameters of a 3-GW 200-kV dc superconducting cable system which influence the transient voltage distribution in the various parts of the cable. The cable system consists of four coaxial metallic cylinders. It was found that the dielectric constant and the electrical resistivity of the soil significantly affect the severity of the transient voltages; lower dielectric constant and higher resistivity of the soil will increase the magnitudes of the transient voltages by increasing the earth-return impedance. It was also found that the effect of the conductor internal impedances of the cable is insignificant. Shorting the coaxial cylinders of the cryogen flow and the cryostat will lessen the severity of the transient voltages. Grounding the second, third, and fourth cylinders at regular intervals with low-impedance grounding impedance will also improve the transient performance of the cable. More research is needed to evaluate these procedures.