A VQ-based blind image restoration algorithm

Learning-based algorithms for image restoration and blind image restoration are proposed. Such algorithms deviate from the traditional approaches in this area, by utilizing priors that are learned from similar images. Original images and their degraded versions by the known degradation operator (restoration problem) are utilized for designing the VQ codebooks. The codevectors are designed using the blurred images. For each such vector, the high frequency information obtained from the original images is also available. During restoration, the high frequency information of a given degraded image is estimated from its low frequency information based on the codebooks. For the blind restoration problem, a number of codebooks are designed corresponding to various versions of the blurring function. Given a noisy and blurred image, one of the codebooks is chosen based on a similarity measure, therefore providing the identification of the blur. To make the restoration process computationally efficient, the principal component analysis (PCA) and VQ-nearest neighbor approaches are utilized. Simulation results are presented to demonstrate the effectiveness of the proposed algorithms.     

Nonstationary Simulation Model of Absorber with Falling Film of Suspension

A nonstationary model of SO₂ absorption from a gas phase to a countercurrent falling film of absorbing slurry was developed. Laminar, wavy and turbulent film structures were considered based on published information. Resistances to the mass transfer on the gas and the liquid sides of the interphase were considered, together with chemical reactions in the liquid phase. Relevant chemical equilibria in the liquid phase were modeled. Original experimental data on the neutralization reagent dissolution rate presented as a polydispersed two‐phase system of solids and on the rate of dissolved sulfite oxidation were used. The model was verified with experimental data from a laboratory‐scale falling‐film absorber using a single vertical tube under various geometrical and operating conditions, and a very good agreement was found with the experiment. Parametric sensitivity analysis showed the critical parts of the model.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Optimised anaerobic treatment of house-sorted biodegradable waste and slaughterhouse waste in a high loaded half technical scale digester.

Anaerobic co-digestion of organic wastes from households, slaughterhouses and meat processing industries was optimised in a half technical scale plant. The plant was operated for 130 days using two different substrates under organic loading rates of 10 and 12 kgCOD.m(-3).d(-1). Since the substrates were rich in fat and protein components (TKN: 12 g.kg(-1) the treatment was challenging. The process was monitored on-line and in the laboratory. It was demonstrated that an intensive and stable co-digestion of partly hydrolysed organic waste and protein rich slaughterhouse waste can be achieved in the balance of inconsistent pH and buffering NH4-N. In the first experimental period the reduction of the substrate COD was almost complete in an overall stable process (COD reduction >82%). In the second period methane productivity increased, but certain intermediate products accumulated constantly. Process design options for a second digestion phase for advanced degradation were investigated. Potential causes for slow and reduced propionic and valeric acid degradation were assessed. Recommendations for full-scale process implementation can be made from the experimental results reported. The highly loaded and stable codigestion of these substrates may be a good technical and economic treatment alternative.     

Analysis of feedback for higher order polarization-mode dispersion mitigation of NRZ 40-Gb/s optical transmission

First-order polarization-mode dispersion (PMD) compensation by means of a polarization controller and a differential delay line is not sufficient to guarantee error-free transmission for 40-Gb/s channels when higher order effects severely increase signal distortion. Higher order mitigation is possible by cascading more than one first-order block. However, only two-stage or three-stage devices remain simple enough to be actually controlled. The performance of such higher order PMD compensators is evaluated by means of numerical simulations. Two different feedback signals have been used, demonstrating that first-order and higher order PMD distortion of nonreturn-to-zero (NRZ) pulses at 40 Gb/s can be strongly mitigated for instantaneous values of the differential group delay (DGD) up to the bit slot, when the compensator is properly controlled.     

Bio-layer management in anaerobic membrane bioreactors for wastewater treatment.

Membrane separation technology represents an alternative way to achieve biomass retention in anaerobic bioreactors for wastewater treatment. Due to high biomass concentrations of anaerobic reactors, cake formation is likely to represent a major cause of flux decline. In the presented research, experiments are performed on the effect of biomass concentration and level of gas sparging on the hydraulic capacity of a submerged anaerobic membrane bioreactor. Both parameters significantly affected the hydraulic capacity, with biomass exerting the most pronounced effect. After 50 days of continuous operation the critical flux remained virtually unchanged, despite an increase in membrane resistance, suggesting that biomass characteristics and hydraulic conditions determine the bio-layer formation rather than the membrane's fouling level. The concept of bio-layer management is introduced to describe the programmed combination of actions performed in order to control the formation of biomass layer over membranes.     

High-resolution photonics-based interference suppression filter with wide passband

A new topology for a photonic signal processor, which overcomes the basic recursive frequency response problem that limits the passband range, is presented. The structure is based on a new multiple-wavelength offset-cavity structure that is cascaded with a series of unbalanced delay line structures. This not only can synthesize a very narrow notch response with good shape factor but also permits a multifold extension of the free spectral range (FSR) and passband width. Results on the interference mitigation filter demonstrate a stopband of 1% of center frequency and a fourfold increase in the FSR and passband width, while also having a very small shape factor, in excellent agreement with predictions.     

Segmented polymer networks containing amino‐dendrimers

Polymer networks in which poly(propylene imine) dendrimers (Astramol?) are connected to each other by linear polytetrahydrofuran (polyTHF) segments, were prepared by two methods. The first method was a one‐step procedure in which bifunctionally living polyTHF, obtained by initiation of the THF polymerization with trifluoromethane sulfonic anhydride (triflic anhydride), was reacted with an amino‐dendrimer. This reaction was very fast but did not allow formation of the end products. The second method was a two‐step procedure. In a first step, living polyTHF, prepared with acryloyloxybutyl triflate as initiator, was grafted on an amino‐dendrimer, to form a star‐like, acrylate‐terminated polyTHF multi‐macromonomer with the dendrimer as core. In a second step, networks were obtained by Michael addition between the acrylate end‐groups and unreacted amino‐groups of the dendrimer. This cross‐linking reaction occurred spontaneously upon heating of the solution of the multi‐macromonomer with gelation times varying from a few minutes to a few hours, depending on the temperature and the composition of the prepolymers. With this method it was possible to prepare networks in the form of coatings or films. © 2003 Society of Chemical Industry