Magnetometer spacing criterion for biomagnetic source currentimaging

A criterion for determining the maximum spacing between magnetometers for measuring the magnetic field is derived. A two-dimensional (2-D) filter model is employed to determine the maximum spatial frequency component present in the magnetic field that is above the spectral noise level. This maximum frequency component is then sampled at a rate greater than twice per period as indicated by the Nyquist criterion, yielding the required magnetometer spacing. It is shown that the rule-of-thumb employed in current clinical biomagnetic array systems, that the spacing between the coils should be approximately equal to the depth of the source, is adequate when the signal-to-noise power ratio is less than 28.4 (14.5 dB). The analysis also quantitatively demonstrates that reducing the separation between the measurement and source planes has a greater effect on the resolution than decreasing the noise level by the same factor. This result is important for employing high T_c superconductor magnetometers that allow thinner thermal insulating layers at the cost of higher thermal noise     

Polymer networks based on α,ω-methacrylate-terminated poly(1,3-dioxolane)

α,ω-Methacrylate-terminated poly(1,3-dioxolane)s (polyDXL) were synthesized by cationic ring-opening polymerization of DXL in the presence of methylene-bis(oxyethylmethacrylate) as transfer agent. If the initiator concentration is small compared with the transfer agent concentration, the molecular weights of the polymers are governed by the ratio of the reacted monomer to the reacted transfer agent. The α,ω-methacrylate-terminated polyDXLs obtained undergo free radical polymerization with formation of polyacetal networks. The properties of the networks as function of the molecular weight of the corresponding prepolymers are reported.     

Low-temperature phase transformation in Li-10 at. % Mg

It is not known whether impaired hematopoiesis noted during human immunodeficiency virus (HIV) infection results from infection of stem/progenitor cells or of cells of the bone marrow microenvironment. Normal adherent primary stromal layers were exposed to HIV to determine which of this mixture of endothelial cells, fibroblasts, and macrophages are susceptible to the virus. Viral p24 in supernatants was noted with monocytotropic HIV-1Ada, HIV-1Ba-L, and HIV-1JR-FL but not with lymphotropic HIV-1LAI nor HIV-1MN strain, and only stromal macrophages expressed the viral antigens. Coculture of the layers with PHA-activated normal lymphocytes failed to rescue lymphotropic virus. No p24 was produced when macrophage-depleted stromal cells were exposed to either HIV-1Ba-L or HIV-1LAI; proviral DNA was then amplified by PCR in cells exposed to either virus, though coculture with lymphocytes rescued only HIV-1Ba-L. Altogether, these data indicate that macrophages are the major targets of HIV in cultured stromal layers. As virus replication in macrophages did not affect the profile of major cytokines involved in regulating hematopoiesis, HIV infection could alter hematopoiesis by other as yet unspecified mechanisms.     

Monitoring systems and determination of actual fatigue usage

At GKN, fatigue monitoring of important components has been conducted since 1979. The monitoring methods depend on the mechanisms of damage; quasi-static loads are regarded as well as dynamic loads. The components were selected for monitoring on the basis of a system analysis. The data resulting from monitoring are used to optimise operation mode steadily. Experience shows that the use of monitoring data as input for fatigue assessment is the most realistic and cost-effective way. This fatigue assessment uses global and local sensitivity studies to evaluate the load-stress relation for each component. These relations can be programmed to produce stress vs. time curves. These are processed according to ASME rules to give a realistic fatigue usage.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Study of photosensitive mixtures of TMAE and helium, hydrocarbon or CF4-based carrier gases

Among the photocathodes used for particle identification based on the Cherenkov Ring Imaging technique, the TMAE molecule is still the best in terms of quantum efficiency. Despite the fact that TMAE gaseous photocathodes have already been used in a number of large experiments, one still seeks answers to many detailed questions. We present a systematic study of gaseous photocathodes based on TMAE mixed with helium, hydrocarbon and CF₄-based gases at normal pressure. The study includes a measurement of the electron drift velocity, gas quenching properties, single electron pulse height spectra and anode wire aging. The paper makes recommendations for carrier gas mixtures to obtain the best quenching, and suggests how to manage TMAE wire aging. This study was motivated by a specific particle identification detector proposal, the Fast Drift CRID proposed for the B-factory at SLAC.     

Afterburner [network-independent card for protocols]

Many current implementations of protocols such as the Transmission Control Protocol/Internet Protocol (TCP/IP) are inefficient because data are often accessed more frequently than necessary. Three techniques that reduce the need for memory bandwidth are proposed. The techniques are copy-on-write, page remapping, and single-copy. Afterburner, a network-independent card that provides the services that are necessary for a single-copy protocol stack, is described. The card has 1 MByte of local buffers and provides a simple interface to a variety of network link adapters, including HIPPI and asynchronous transfer mode (ATM). Afterburner can support transfers to and from the link adapter card at rates up to 1 Gbit/s. An implementation of TCP/IP that uses the features provided by Afterburner to reduce the movement of data to a single copy is discussed. Measurements of the end-to-end performance of Afterburner and the single-copy implementation of TCP/IP are presented     

The evolution of custom microarray manufacture

Given the enormous size of the genome and that there are potentially many other types of measurements we need to do to understand it, it has become necessary to pick and choose one's targets to measure because it is still impossible to evaluate the entire genome all at once. What has emerged is a need to have rapidly customizable microarrays. There are two dominant methods to accomplish custom microarray synthesis, Affymetrix-like microarrays manufactured using light projection rather than semiconductor-like masks used by Affymetrix to mass manufacture their GeneChip/sup TM/ arrays now, or the ink-jet printing method employed by Agilent. The manufacture of these custom Affymetrix-like microarrays can now be done on a digital optical chemistry (DOC) machine developed at the University of Texas Southwestern Medical Center, and this method offers much higher feature numbers and feature density than is possible with ink-jet printed arrays. On a microarray, each feature contains a single genetic measurement. The initial DOC prototype has been described in several publications, but that has now led to a second-generation machine. This machine reliably produces a number of arrays daily, has been deployed against a number of biomedical questions, is being used in new ways and has also led to a number of spin-off technologies.     

Functional Properties and Food Applications of Rapeseed Protein Concentrate

Rapeseed protein concentrate (RC), prepared with 2% hexameta-phosphate, was tested for its functionality and performance in some foods. The RC had good nitrogen solubility, fat absorption, emulsification, and whipping capacities but poor water absorption and gelling properties. It increased the emulsion stability, and protein but lowered the fat content of wieners. It also increased the cooking yield, reduced the shrinkage and tenderized meat patties. Results were similar to soybean isolate except for the poorer color and flavor. The cooking yield of RC supplemented wieners was less than the all-meat control and soybean-supplemented wieners. A 9% RC dispersion mixed with an equal volume of eggwhite produced a meringue of comparable stability and texture to that of eggwhite alone.