Treatment of low strength domestic wastewater using the anaerobic filter

A laboratory scale anaerobic filter packed with synthetic high surface area trickling filter media was used to treat a low strength domestic wastewater averaging 288 mg 1⁻¹ COD. The filter was operated for 60 days after reaching steady-state at 20, 25, 35°C at a loading rate of 0.02 lb COD ft⁻³ day⁻¹ and 24 h hydraulic retention time. Filter effluent BOD₅ averaged 38 mg 1⁻¹ providing an average removal rate of 79%, and effluent COD averaged 78 mg 1⁻¹, corresponding to a 73% removal rate. Removal efficiencies showed very little sensitivity to daily fluctuations in influent wastewater quality. The filter performance at 25 and 35°C was not significantly different, but BOD and TSS removal efficiency declined a: 20°C. Gas production averaged 0.027 ft⁻³ of gas per ft³ of influent wastewater, or 1.875 ft³ of gas per pound of influent COD. Gas composition averaged 30% nitrogen, 65% methane, and 5% carbon dioxide. Ammonia nitrogen and sulfides both increased during treatment. It is concluded that the anaerobic filter is a promising candidate for treatment of low strength wastewaters and that post treatment for sulfides and ammonia may be necessary.     

Peroxodisulfate generation on boron-doped diamond microelectrodes array and detection by scanning electrochemical microscopy

In this work, the electrogeneration of peroxodisulfate from a 1 M H₂SO₄ solution on boron-doped diamond microelectrodes array has been studied. The peroxodisulfate is detected at the vicinity of the boron doped diamond electrode, with the SECM probe, only when the polarization of the microarray is greater than 2.1 V versus AgCl/Ag. The main electrochemical interest of working with microarrays comes from the fact that current densities and efficiencies are comparable to those observed in the peroxodisulfate industrial production. The local Scanning Electrochemical Microscopy studies have shown that the peroxodisulfate reaction is related to a surface mediated oxidation of sulfate anions into peroxodisulfate according to a complex reactional mechanism.     

Human Adipose Tissue Conditioned Media from Lean Subjects Is Protective against H2O2 Induced Neurotoxicity in Human SH-SY5Y Neuronal Cells

Adipose tissue secretes numerous hormone-like factors, which are known as adipokines. Adipokine receptors have been identified in the central nervous system but the potential role of adipokine signaling in neuroprotection is unclear. The aim of this study is to determine (1) Whether adipokines secreted from cultured adipose tissue of lean humans is protective against oxidative stress-induced neurotoxicity in human SH-SY5Y neuronal cells; and (2) To explore potential signaling pathways involved in these processes. Adipose tissue conditioned media (ATCM) from healthy lean subjects completely prevented H₂O₂ induced neurotoxicity, while this effect is lost after heating ATCM. ATCM activated the phosphorylation of ERK1/2, JNK and Akt at serine 308 in SH-SY5Y cells. PD98059 (25 µM), SP600125 (5 µM) and LY29400 (20 µM) partially blocked the protective effects of ATCM against H₂O₂ induced neurotoxicity. Findings demonstrate that heat-sensitive factors secreted from human adipose tissue of lean subjects are protective against H₂O₂ induced neurotoxicity and ERK1/2, JNK, and PI3K signaling pathways are involved in these processes. In conclusion, this study demonstrates preliminary but encouraging data to further support that adipose tissue secreted factors from lean human subjects might possess neuroprotective properties and unravel the specific roles of ERK1/2, JNK and PI3K in these processes.     

Entropy generation of viscous dissipative nanofluid flow in microchannels

An analytical study on the viscous dissipation effect on entropy generation in laminar fully developed forced convection of water–alumina nanofluid in circular microchannels is reported. In the first-law analysis, closed form solutions of the temperature distributions in the radial direction for the models with and without viscous dissipation term in the energy equation are obtained. The results show that the heat transfer coefficient decreases with nanoparticle volume fraction largely in the laminar regime of nanofluid flow in microchannel when the viscous dissipation effect is taken into account. In the second-law analysis, the two models are compared by analyzing their relative deviations in entropy generation for different Reynolds number and nanoparticle volume fraction. When the viscous dissipation is taken into account, the temperature distribution is prominently affected and consequently the entropy generation ascribable to the heat transfer irreversibility is significantly increased. The increase of entropy generation induced by the increase of nanoparticle volume fraction is attributed to the increase of both the thermal conductivity and viscosity of nanofluid which causes augmentation in the heat transfer and fluid friction irreversibilities, respectively. By incorporating the viscous dissipation effect, both thermal performance and exergetic effectiveness for forced convection of nanofluid in microchannels dwindle with nanoparticle volume fraction, contrary to the widespread conjecture that nanofluids possess advantage over pure fluid associated with higher overall effectiveness from the aspects of first-law and second-law of thermodynamics.     

Effects of pH on rhodopsin photointermediates from lumirhodopsin to metarhodopsin II

Time-resolved absorption difference spectra of membrane suspensions of bovine rhodopsin at pH 5, 6, 7, 8, 9, and 10 were collected in the time range from 1 micro s to 200 ms after laser photolysis with 7-ns pulses of 477-nm light. The data were analyzed using singular value decomposition (SVD) and global exponential fitting. At pH 7 the data agree well with previously obtained data (Thorgeirsson et al. (1993) Biochemistry 32, 13861-13872) with fits improved at all pH's by inclusion of a small component due to an absorbance change caused by rotational diffusion which is detectable even at magic angle polarization. A "square scheme" suggested to best explain the previous data, which involves two branches following decay of the lumi intermediate with pathways (1) lumi --> MI480 right harpoon over left harpoon MII and (2) lumi right harpoon over left harpoon MI380 --> MII, could be confirmed throughout the entire pH range. However, to account for the increased rate of the MII --> MI480 reaction in path 1 for rising pH values, we propose that the MII in the square scheme consists of deprotonated MII and protonated MIIH+ forms in rapid equilibrium with each other, resulting in an extended square scheme and increasing the number of 380-nm products from two to three. In addition to the kinetic processes described by the extended square scheme, above pH 8 fast ( approximately 10 micro s) and slow ( approximately 50 ms) components were found. The fast component was assigned to the decay of a blue-shifted lumi intermediate, and the slow component, resolvable only at pH 10, was assigned to formation of a 450 nm absorbing photoproduct.     

Metallic interconnects for solid oxide fuel cell: A review on protective coating and deposition techniques

With the reduction of solid oxide fuel cells (SOFCs) operating temperature to the range of 600 °C–800 °C, metallic alloy with high oxidation resistance are used to replace traditional ceramic interconnects. Metallic interconnects is advantageous over ceramic interconnects; in terms of manufacturability, cost, mechanical strength, and electrical conductivity. To date, promising candidates for metallic interconnects are all Cr-containing alloys, which are susceptible to volatile Cr migration that causes cell degradation. As such, protective coatings have been developed to effectively inhibit Cr migration; as well as maintain excellent electrical conductivity and good oxidation resistance. This article reviews the progress and technical challenges in developing metallic interconnects; different types of protective coatings and deposition techniques for metallic interconnects for intermediate-temperature SOFC applications.     

Skin diseases in Bamako (Mali)

BACKGROUND: Skin diseases have only recently been considered as a possible public health problem in developing countries. Data supporting this matter are scarce. The aim of this study is to report the experience of a specialized dermatologic center in Bamako (Mali) in order to complete two previous studies conducted in the Bamako area: a prevalence study in the general population and a study in nonspecialized health centers of Bamako. It is our intention to provide a comprehensive picture of the problem of skin diseases in an African developing country. METHODS: We retrospectively collected all cases of skin diseases diagnosed during consultations provided at the Institut Marchoux in Bamako, the only center specializing in dermatology in Mali, during the year 1993. RESULTS: A total of 10,575 new outpatients were seen with 10,889 skin diseases. The main skin diseases registered were as follows: infectious dermatoses (41% of all diagnoses, including scabies (16.6%), superficial mycoses (13.6%), and primary pyoderma (5.6%)), dermatitis (20.4%), papular urticaria (4.4%), acne (4.2%), pityriasis alba (3.6%), keratoderma (3.6%), and urticaria (3%). Typical tropical infectious diseases accounted for only 1% of all diagnoses. CONCLUSIONS: It appears that certain skin diseases (mainly scabies and pyoderma) are an important health problem for the population of the Bamako area. Public health policies should be implemented in order to manage this problem rationally.     

Interface analysis of Si-C-O fibre/magnesium aluminosilicate matrix composites

Interface characteristics of Si-C-O (Nicalon^R) fibre-reinforced glass ceramic matrix composites were studied using scanning Auger microscopy (SAM). Composites with and without the cation additions of Ba, Nb, Zr, Li and Li-Zr-Nb to the magnesium aluminosilicate (MAS) matrix were fracturedin situ under ultrahigh vacuum. SAM depth profiles and flexural strength results showed the compositional effects of the additives in the fibre-matrix interface region.