Combined biological and ozone treatment of log yard run-off

Batch biological treatment of log yard run-off reduced biochemical oxygen demand (BOD), chemical oxygen demand (COD) and tannin and lignin (TL) concentration by 99%, 80%, and 90%, respectively. Acute (Microtox) toxicity was decreased over treatment, from an initial EC50 of 1.83% to a value of 50.4% after 48 h of treatment. Kinetics of biodegradation were determined using respirometry and fitted using the Monod and Tessier model. For the Monod model the maximum substrate uptake rate, and Ks values determined were 0.0038 mg BOD/mgVSS min, and 1.4 mg/L, respectively. The efficacy of ozone as a pre- and post- biological treatment stage was also assessed. During ozone pretreatment, TL concentration and acute toxicity were rapidly reduced by 70% and 71%, respectively. Pre-ozonation reduced BOD and COD concentration by < 10%, however a larger fraction of residual COD was non biodegradable after ozonation. Biologically treated effluent was subjected to ozonation to determine whether further improvements in effluent quality could be achieved. A reduction in COD and TL concentration was observed during ozonation, however no further improvement in toxicity was observed. Ozonation increased BOD by 38%, due to conversion of COD to BOD.     

Characterization of Gum Ghatti (Anogeissus latifolia): A Structural and Rheological Approach

ABSTRACT:  Gatifolia, a commercial gum ghatti ( Anogeissus latifolia ) product was studied for its structural, thermal, and rheological characteristics. This study may prove helpful for the use of gum ghatti in a diverse range of food applications. The molecular weight ( M _W) and  R_g  (radius of gyration) for gum ghatti were calculated to be approximately 8.94 × 10⁷ g/mol and 140 nm, respectively, using high-performance size exclusion chromatography (HPSEC) system combined with multi-angle laser light scattering (MALLS). Gum ghatti solutions exhibited pseudoplastic behavior (as determined by flow experiments), which became more prevalent with increasing concentrations. Gum ghatti also displayed time-dependent shear-thickening behavior and showed negative hysteresis during up–down flow measurements. Under the measurement conditions at the range of frequencies and temperatures studied, the gum did not behave as a typical viscoelastic gel.     

High melting lipid based approach for drug delivery: Solid lipid nanoparticles

Poor solubility of newly developed drug molecules is the main problem in recent drug discovery research, so novel drug delivery approaches are being used to deliver these molecular entities for pharmacological action. Colloidal carriers (emulsion, suspensions, liposomes, polymer nanoparticles and solid lipid nanoparticles) have been used to administer poorly soluble drugs, but solid lipid nanoparticles are found to be the most reliable carriers for this type of drugs due to its advantages over other carriers. Solid lipid nanoparticles have the potential to solve the drug delivery problems with safe excipients used in its formulation. In this review all the aspects of solid lipid nanoparticles production, stability, characterization, differentiation based on route, preservation and storage have been discussed.     

Effect of clay on the corrosion inhibition and dynamic mechanical properties of epoxy ester–polyurea–polysiloxane hybrid coatings

The corrosion resistance of polymeric coatings containing epoxy ester, polyurea, and polymethylhydrosiloxane was significantly improved by the addition of cloisite 15A organoclay. The weight percent of organoclay was varied from 0.5 to 10%. The presence of organoclay in the coatings was confirmed using the Fourier transformed infrared spectroscopy. The effect of organoclay on the surface energy of the coatings was analyzed by measuring contact angle with a video contact angle analyzer and using water and iodomethane as the probing liquids. The surface energy of the coatings increased with increasing organoclay concentration. The corrosion resistant properties were measured by direct current polarization technique. The addition of organoclay enhanced the corrosion resistance of the coatings, and the best corrosion resistance was shown by coating containing 1% organoclay. The dynamic mechanical property of the coatings was determined using the dynamic mechanical spectrometer. The glass transition temperature of the films decreased significantly with the addition of organoclay up to 1% after which it increased with additional increase in the wt% of organoclay. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Physicochemical,cooking and textural characteristics of some Indian black gram (Phaseolus mungo L) varieties

Physicochemical, cooking and textural properties of black gram varieties were studied and related to each other using Pearson correlation. Different varieties showed significant variation in their physicochemical, cooking and textural properties. Varieties having higher seed weight and seed volume had higher values of cooking time, swelling capacity, hydration capacity and hardness. The relationships between textural parameters of cooked grains from different black gram varieties showed a significant positive correlation of hardness with cohesiveness (r = 0.472), gumminess (r = 0.938) and chewiness (r = 0.859). Swelling index, cohesiveness and gumminess of black gram varieties were observed to be related to their fibre content. Swelling capacity and swelling index correlated well with cooking time, hardness and gumminess. Cooking time had a positive correlation with hardness (p < 0.05) and gumminess (p < 0.05) and a negative correlation with springiness. Copyright © 2004 Society of Chemical Industry     

Textural and pasting properties of potatoes (Solanum tuberosum L.) as affected by storage temperature

Fresh tubers from five potato (Solanum tuberosum L.) cultivars were stored at different temperatures (4, 8, 12, 16 and 20 °C) and 80–90% relative humidity for 18 weeks after harvest to examine the effect of storage temperature on their textural and pasting properties. Texture profile analysis was performed on raw and cooked potatoes using an Instron universal testing machine to measure textural parameters such as fracturability, hardness, cohesiveness, adhesiveness and springiness. Both raw and cooked potato tubers showed a considerable reduction in all textural parameters upon storage, irrespective of the storage temperature employed. Raw potatoes showed a decrease in fracturability and hardness with increasing storage temperature, whereas their cooked counterparts showed the opposite trend. The extent of change in the textural properties of both raw and cooked potatoes also varied among the different cultivars. Fresh and stored tubers from all cultivars were freeze‐dried, ground into flours and analysed for amylose content and pasting properties. The amylose content of flours prepared from potatoes stored at 4 and 8 °C was observed to be considerably lower than that of flours prepared from potatoes stored at 16 and 20 °C. Pasting characteristics such as peak viscosity, setback and final viscosity increased with increasing storage temperature, while the reverse was observed for pasting temperature, when studied using a rapid visco analyser. Breakdown in viscosity of the flour pastes from all cultivars was considerably reduced during storage, irrespective of the storage temperature employed. Copyright © 2006 Society of Chemical Industry     

Influence of addition of insoluble solids,different yeast strains and pectinesterase enzyme on the quality of apple wine

Rate of fermentation and physico‐chemical characteristics of apple wines, owing to the addition of different yeast strains, insoluble solids and pectinesterase enzyme, were examined. The highest rates of fermentation and ethanol production were found in the wine fermented by yeast strain UCD 505, while strain UCD 595 gave the smallest amount of methanol. The addition of insoluble solids to the apple juice significantly increased the levels of methanol, vitamin C, amyl alcohol, total volatiles, rate of fermentation, tannins, colour units, Mn and Zn. Addition of insoluble solids decreased pH, titrable acidity, ethanol, total sugars, total esters, and K, Mg, Ca, Cu and Fe content of the wine. Addition of pectinesterase enzyme significantly increased all the parameters examined except for pH, vitamin C, total esters, Mn and Mg content. Application of cluster analysis to the results of rate of fermentation, reducing sugars, volatile acidity and ethanol showed that the influence of the yeast strains was more than the influence of insoluble solids or pectinesterase enzyme addition. Consideration of more parameters showed that there was a clear interaction between the yeast strain, insoluble solids and the pectinesterase enzyme. Addition of insoluble solids to the must led to the production of some undesirable quality characteristics. In contrast, specific yeast strains and enzyme addition improved various physico‐chemical characteristics of the wine. Pre‐settled or clarified juice was preferred to produce a quality apple wine. Copyright © 2013 The Institute of Brewing & Distilling     

Synthesis and applications of magnetic nanoparticles for biorecognition and point of care medical diagnostics

Functionalized magnetic nanoparticles are important components in biorecognition and medical diagnostics. Here, we present a review of our contribution to this interdisciplinary research field. We start by describing a simple one-step process for the synthesis of highly uniform ferrite nanoparticles (d = 20-200 nm) and their functionalization with amino acids via carboxyl groups. For real-world applications, we used admicellar polymerization to produce 200 nm diameter 'FG beads', consisting of several 40 nm diameter ferrite nanoparticles encapsulated in a co-polymer of styrene and glycidyl methacrylate for high throughput molecular screening. The highly dispersive FG beads were functionalized with an ethylene glycol diglycidyl ether spacer and used for affinity purification of methotrexate-an anti-cancer agent. We synthesized sub-100 nm diameter magnetic nanocapsules by exploiting the self-assembly of viral capsid protein pentamers, where single 8, 20, and 27 nm nanoparticles were encapsulated with VP1 pentamers for applications including MRI contrast agents. The FG beads are now commercially available for use in fully automated bio-screening systems. We also incorporated europium complexes inside a polymer matrix to produce 140 nm diameter fluorescent-ferrite beads (FF beads), which emit at 618 nm. These FF beads were used for immunofluorescent staining for diagnosis of cancer metastases to lymph nodes during cancer resection surgery by labeling tumor cell epidermal growth factor receptor (EGFRs), and for the detection of brain natriuretic peptide (BNP)-a hormone secreted in excess amounts by the heart when stressed-to a level of 2.0 pg ml(-1). We also describe our work on Hall biosensors made using InSb and GaAs/InGaAs/AlGaAs 2DEG heterostructures integrated with gold current strips to reduce measurement times. Our approach for the detection of sub-200 nm magnetic bead is also described: we exploit the magnetically induced capture of micrometer sized 'probe beads' by nanometer sized 'target beads', enabling the detection of small concentrations of beads as small as 8 nm in 'pumpless' microcapillary systems. Finally, we describe a 'label-less homogeneous' procedure referred to as 'magneto-optical transmission (MT) sensing', where the optical transmission of a solution containing rotating linear chains of magnetic nanobeads was used to detect biomolecules with pM-level sensitivity with a dynamic range of more than four orders of magnitude. Our research on the synthesis and applications of nanoparticles is particularly suitable for point of care diagnostics.     

Outcomes following physical restraint reduction programs in two acute care hospitals.

BACKGROUND: Physical restraint rates can be reduced safely in long term care settings, but the strategies used to prevent wandering, falls, and patient aggression have not been tested for their effectiveness in preventing therapy disruption. A restraint reduction program (RRP) consisting of four core components (administrative, educational, consultative, and feedback) was implemented in 1998-1999 in 14 units at two acute care hospitals in geographically distant cities. METHODS: The RRP was targeted at units with prevalence rates of > or = 4% for non-intensive care units (non-ICUs) and > or = 25% for ICUs, as well as two additional units. The RRP was implemented by an interdisciplinary team consisting of geriatricians and nurse specialists. RESULTS: Of the 16,605 admissions to the RRP units, 2,772 cases received RRP consultations. Only six units (four of seven general units and two of six ICUs) demonstrated a relative reduction of > or = 20% in the physical restraint use rate. No increase in secondary outcomes of patient falls and therapy disruptions (patient-initiated discontinuation or dislodgment of therapeutic devices) occurred, injury rates were low, and no deaths occurred as a direct result of either a fall or therapy disruption event. DISCUSSION: Given the minimal success in the ICU settings, further studies are needed to determine effective nonrestraint strategies for critical care patients. ICU clinicians need to be persuaded of the favorable risk-to-benefit ratio of alternatives to physical restraint before they will change their practice patterns. SUMMARY: Efforts to identify more effective interventions that match patient needs and to identify non-clinician factors that affect physical restraint use are needed.     

Exergy analysis of integrated photovoltaic thermal solar water heater under constant flow rate and constant collection temperature modes

In this communication, an analytical expression for the water temperature of an integrated photovoltaic thermal solar (IPVTS) water heater under constant flow rate hot water withdrawal has been obtained. Analysis is based on basic energy balance for hybrid flat plate collector and storage tank, respectively, in the terms of design and climatic parameters. Further, an analysis has also been extended for hot water withdrawal at constant collection temperature. Numerical computations have been carried out for the design and climatic parameters of the system used by Huang et al. [Huang BJ, Lin TH, Hung WC, Sun FS. Performance evaluation of solar photovoltaic/thermal systems. Sol Energy 2001; 70(5): 443–8]. It is observed that the daily overall thermal efficiency of IPVTS system increases with increase constant flow rate and decrease with increase of constant collection temperature. The exergy analysis of IPVTS system has also been carried out. It is further to be noted that the overall exergy and thermal efficiency of an integrated photovoltaic thermal solar system (IPVTS) is maximum at the hot water withdrawal flow rate of 0.006 kg/s. The hourly net electrical power available from the system has also been evaluated.