Experimental demonstration of enhancing pump absorption rate in cladding-pumped ytterbium-doped fiber lasers using pump-coupling long-period fiber gratings

A long-period fiber grating (LPFG) was inscribed in a single-mode fiber and was spliced with a ytterbium (Yb)-doped double-clad fiber in order to couple pump radiation of the inner cladding into the core in a cladding-pumped fiber laser. The use of an LPFG permits a partial core-pumping scheme in a cladding-pumping fiber laser because a portion of the pump radiation can be coupled to the core by LPFG. The enhancement of the pump absorption of a Yb-doped cladding-pumped fiber laser as the result of pump coupling by LPFG was 35%, and the maximal output power increased by up to 55% when a 20-W pump source is used.     

A 20-GHz phase-locked loop for 40-gb/s serializing transmitter in 0.13-/spl mu/m CMOS

A 20-GHz phase-locked loop with 4.9 ps/sub pp//0.65 ps/sub rms/ jitter and -113.5 dBc/Hz phase noise at 10-MHz offset is presented. A half-duty sampled-feedforward loop filter that simply replaces the resistor with a switch and an inverter suppresses the reference spur down to -44.0 dBc. A design iteration procedure is outlined that minimizes the phase noise of a negative-g/sub m/ oscillator with a coupled microstrip resonator. Static frequency dividers made of pulsed latches operate faster than those made of flip-flops and achieve near 2:1 frequency range. The phase-locked loop fabricated in a 0.13-/spl mu/m CMOS operates from 17.6 to 19.4GHz and dissipates 480mW.     

High average power, high repetition rate, picosecond pulsed fiber master oscillator power amplifier source seeded by a gain-switched laser diode at 1060 nm

We demonstrate a pulsed ytterbium-doped fiber master-oscillator power amplifier source at 1060 nm producing over 300 W of average power in 20-ps pulses at 1-GHz repetition rate. The pulses generated by a gain-switched diode were compressed by a chirped fiber Bragg grating and amplified without any distortion with excellent spectral quality. This fiber master oscillator power amplifier system offers versatility and potential for further power scaling.     

Computation sharing programmable FIR filter for low-power and high-performance applications

This paper presents a programmable digital finite-impulse response (FIR) filter for high-performance and low-power applications. The architecture is based on a computation sharing multiplier (CSHM) which specifically targets computation re-use in vector-scalar products and can be effectively used in the low-complexity programmable FIR filter design. Efficient circuit-level techniques, namely a new carry-select adder and conditional capture flip-flop (CCFF), are also used to further improve power and performance. A 10-tap programmable FIR filter was implemented and fabricated in CMOS 0.25-/spl mu/m technology based on the proposed architectural and circuit-level techniques. The chip's core contains approximately 130 K transistors and occupies 9.93 mm/sup 2/ area.     

A 980-nm Yb-doped fiber MOPA source and its frequency doubling

A continuous-wave (CW) master oscillator-power amplifier (MOPA) fiber source, tunable around 978 nm, was frequency-doubled to 488.7 nm. Both the laser and the amplifier were made with cladding-pumped jacketed air-clad Yb-doped fibers. The MOPA generated up to 2.7 W of power in an output beam with an M/sup 2/ value of 1.8. This was frequency-doubled in a periodically poled potassium titanyl phosphate crystal at room temperature, in a single-pass configuration. The generated blue light had a CW power of 18.1 mW, a nearly Gaussian spatial intensity profile, and an M/sup 2/ value of 1.7.     

Personalized Healthcare System for Chronic Disease Care in Cloud Environment

The rapid increase in the number of patients with chronic diseases is an important public healthcare issue in many countries, which accelerates many studies on a healthcare system that can, whenever and wherever, extract and process patient data. A patient with a chronic disease conducts self‐management in an out‐of‐hospital environment, particularly in an at‐home environment, so it is important to provide integrated and personalized healthcare services for effective care. To help provide effective care for chronic disease patients, we propose a service flow and a new cloud‐based personalized healthcare system architecture supporting both at‐home and at‐hospital environments. The system considers the different characteristics of at‐hospital and at‐home environments, and it provides various chronic disease care services. A prototype implementation and a predicted cost model are provided to show the effectiveness of the system. The proposed personalized healthcare system can support cost‐effective disease care in an at‐hospital environment and personalized self‐management of chronic disease in an at‐home environment.     

Consideration of the Actual Current-Spreading Length of GaN-Based Light-Emitting Diodes for High-Efficiency Design

Based on the proposed experimental method, the current spreading length of GaN-based light-emitting diodes (LEDs) was measured and analyzed for practical device design. In this study, Thompson's and Guo's models, which are categorized according to vertical series resistance (in particular, p-type contact resistance), were used to extract device parameters. It was shown that the measured current spreading length strongly depends on the injected current density. For LEDs fabricated with low-resistance p-type contacts, this behavior could be explained in terms of the accelerated current crowding with higher current densities occurring as a result of the reduced voltage drop across the junction, which is in good agreement with Thompson's relation. However, for LEDs fabricated with high-resistance p-contacts, unlike Guo's prediction, the measured current spreading length also showed a strong dependence on the injected current density. This was attributed to thermal heating at the p-contact, resulting in the reduction of the voltage drop across the p-contact and so junction voltage, which is also in agreement with Thompson's model. Based on the measured parameters and the design rule, efficient p-type reflectors, namely, hybrid reflectors were designed. Compared with conventional ones, LEDs fabricated with the hybrid reflectors exhibited better output power at a reasonable forward voltage, indicating that the proposed method is effective in understanding the actual current spreading and hence the practical design of high-efficiency LEDs.     

An SSD‐Based Storage System for an Interactive Media Server Using Video Frame Grouping

For real‐time interactive multimedia operations, such as video uploading, video play, fast‐forward, and fast‐rewind, solid state disk (SSD)‐based storage systems for video streaming servers are becoming more important. Random access rates in storage systems increase significantly with the number of users; it is thus difficult to simultaneously serve many users with HDD‐based storage systems, which have low random access performance. Because there is no mechanical operation in NAND flash‐based SSDs, they outperform HDDs in terms of flexible random access operation. In addition, due to the multichannel architecture of SSDs, they perform similarly to HDDs in terms of sequential access. In this paper, we propose a new SSD‐based storage system for interactive media servers. Based on the proposed method, it is possible to maximize the channel utilization of the SSD's multichannel architecture. Accordingly, we can improve the performance of SSD‐based storage systems for interactive media operations.     

Environmental effects on the electrical behavior of pentacene thin-film transistors with a poly(methyl methacrylate) gate insulator

The electrical properties of top-contact pentacene thin-film transistors (TFTs) with a poly(methyl methacrylate) (PMMA) gate dielectric were analyzed in air and vacuum environments. Compared to the vacuum case, the pentacene TFT in air exhibited lower drain currents and more pronounced shifts in the threshold voltage upon reversal of the gate voltage sweep direction, together with a decrease in the field-effect mobility. These characteristic variations were explained in terms of two distinctive actions of polar H₂O molecules in pentacene TFT. H₂O molecules were suggested to diffuse under the source and drain contacts and interrupt the charge injection into the pentacene film, whereas those that permeate at the pentacene/PMMA interface retard hole depletion in and around the TFT channel. The diffusion process was much slower than the permeation process. The degraded TFT characteristics in air could be recovered mostly by storing the device under vacuum, which suggests that the air instability of TFTs is due mainly to the physical adsorption of H₂O molecules within the pentacene film.     

Cue-based networking

In this paper we present a new approach called cue-based networking that uses hints or cues about the physical environment to optimize networked application behavior. We define the notion of cues and describe how cues can be obtained using wireless sensor networks as the underlying platform. We identify both the research and system challenges that need to be addressed to realize benefits of the approach under a target application of video delivery over IP networks. In the process, we identify key challenges of wireless sensor networks, namely timeliness and robustness. We design an adaptive algorithm that balances the tradeoff between them satisfying both timeliness and robustness requirements. Through an implementation of the video delivery application using the proposed algorithm in a real home environment, we highlight the practical benefits of the proposed approach.