Two additional cases of metformin‐associated encephalopathy in patients with end‐stage renal disease undergoing hemodialysis

We report on two additional cases of metformin‐associated encephalopathy in patients with end‐stage renal disease (ESRD) undergoing hemodialysis. Two patients were seen at our hospital with abnormal neurological signs and symptoms. Magnetic resonance imaging (MRI) revealed the same pattern of high signal intensity in both basal ganglia in T2‐weighted images in the two patients. The two patients had started taking metformin 5 and 6 weeks earlier at the same dose of 1000 mg per day. Metformin was immediately stopped, and regular hemodialysis was conducted. Their signs and symptoms resolved completely after these measures. The high signal intensity in both ganglia in T2‐weighted MRI also disappeared. We should suspect metformin‐induced encephalopathy and withdraw the drug when presented with diabetic patients with chronic kidney disease and neurological signs and symptoms of unknown cause.     

Crumple zone design for pedestrian protection using impact analysis

This paper describes the design process for an automobile crumple zone for pedestrian protection. The impact load and bending moments predicted by impact analysis were used to design a plastic structure that may help reduce pedestrian injuries to the thigh area. The fracture effect was incorporated into the model by calculating the damage to the plastic material during impact, and the analysis was conducted under the European New Car Assessment Program (Euro NCAP) test conditions, using the upper legform developed by ESI Corporation. In addition, the values predicted by the analysis were validated by comparison with results of actual impact tests.     

Effective suppression of deactivation by utilizing Ni-doped ordered mesoporous alumina-supported catalysts for the production of hydrogen and CO gas mixture from methane

Several different kinds of ordered mesoporous alumina (OMA)-supported and Ni-doped OMA-supported Ni catalysts have been prepared for catalytic partial oxidation of methane (CPOM) to produce hydrogen and CO gas mixture. The Ni metal was incorporated in various ways of the impregnation, the doping, and the partial doping followed by impregnation. The prepared OMA-supported catalysts showed a wormhole-like, pseudo-hexagonal structure. By incorporating Ni in the OMA matrix during synthesis of supports, the resulting catalysts showed better-distributed and less-sintered nanocrystals even after CPOM at elevated temperature for over 100 h. By employing the partial doping of Ni followed by impregnation of Ni, the prepared CPOM catalyst was found more productive due to the well-distributed and well-anchored Ni nanocrystals inside the OMA matrix and the confined ordered mesopores as well. Through the test under non-stoichiometric feed ratio, the catalyst prepared only by impregnation was found vulnerable to carbon deposition and deactivated more rapidly. Even worse, the formation rate of carbon deposition was so fast that the test could not be conducted due to the increased pressure difference. In contrast, the highly distributed Ni nanocrystals partially or fully utilizing doping were found to have stronger resistance to carbon deposition.     

Assessment of printability for printed electronics patterns by measuring geometric dimensions and defining assessment parameters

The printability of patterns for printed electronic devices determines the performance, yield rate, and reliability of the devices; therefore, it should be assessed quantitatively. In this paper, parameters for printability assessment of printed patterns for width, pinholes, and edge waviness are suggested. For quantitative printability assessment, printability grades for each parameter are proposed according to the parameter values. As examples of printability assessment, printed line patterns and mesh patterns obtained using roll-to-roll gravure printing are used. Both single-line patterns and mesh patterns show different levels of printability, even in samples obtained using the same printing equipment and conditions. Therefore, for reliable assessment, it is necessary to assess the printability of the patterns by enlarging the sampling area and increasing the number of samples. We can predict the performance of printed electronic devices by assessing the printability of the patterns that constitute them.

     

Die quenching limit of AA2024 aluminum alloy billet on servo press

Die quenching of AA2024 aluminum alloy billets was carried out on a servo press with ram-motion control of WC-20 mass%Co dies directly after solution heat treatment (SHT). To clarify the dependence on billet size for die quenching, two billets with a height of h₀ = 8 mm or 16 mm and with the same diameter of 16 mm were prepared. The cylindrical billets were heated in an electric furnace at 823 K and transferred to the press. Then the billets were uniaxially compressed with a reduction in height (Δh/h₀) of 2% or 5%, and further held between the dies. The sandwiching duration by dies (t_d.q.) was varied from 0 to 8 s. Based a measured temperature change, hardness and TG–DTA analysis, it is found that die quenching is successfully carried out without precipitation hardening only in the case of the billet with a height of 8 mm and t_d.q. > 6 s. The reduction in height is limited less than 5% by intergranular fracture on side surface of billet during the die quenching process.     

Anti-diabetic effects of mulberry (Morus alba L.) branches and oxyresveratrol in streptozotocin-induced diabetic mice

Food Science and Biotechnology - Despite with accumulating evidences on the anti-diabetic effects of mulberry branch (MB), the major active component for the activity has not been known. Oral...     

Activation of the Complement System on Human Endothelial Cells by Urban Particulate Matter Triggers Inflammation-Related Protein Production

Exposure to particulate matter (PM) is becoming a major global health issue. The amount and time of exposure to PM are known to be closely associated with cardiovascular diseases. However, the mechanism through which PM affects the vascular system is still not clear. Endothelial cells line the interior surface of blood vessels and actively interact with plasma proteins, including the complement system. Unregulated complement activation caused by invaders, such as pollutants, may promote endothelial inflammation. In the present study, we sought to investigate whether urban PM (UPM) acts on the endothelial environment via the complement system. UPM-treated human endothelial cells with normal human serum showed the deposition of membrane attack complexes (MACs) on the cell surface via the alternative pathway of the complement system. Despite the formation of MACs, cell death was not observed, and cell proliferation was increased in UPM-mediated complement activation. Furthermore, complement activation on endothelial cells stimulated the production of inflammation-related proteins. Our results revealed that UPM could activate the complement system in human endothelial cells and that complement activation regulated inflammatory reaction in microenvironment. These findings provide clues with regard to the role of the complement system in pathophysiologic events of vascular disease elicited by air pollution.     

Predictively encoded graph convolutional network for noise-robust skeleton-based action recognition

Applied Intelligence - In skeleton-based action recognition, graph convolutional networks (GCNs), which model human body skeletons using graphical components such as nodes and connections, have...     

Numerical simulation of gas-assisted polymer-melt electrospinning: Parametric study of a multinozzle system for mass production

In this study, we developed a multiphysics model for simulation of a gas-assisted melt-electrospinning (GAME) process, focusing on jet formation and propagation behavior. By numerically calculating the stresses acting on the jet during a single-nozzle GAME process, the shear viscous stress was identified as the main factor with respect to jet stretch; thus, the relationship between shear viscous stress and jet thickness was investigated. The jet stretch ratio increased sharply when shear viscous stress reached the level at which jet sharpening occurred, leading to stable jet formation. We defined this stress as the critical shear viscous stress to determine stable spinnability. By imposing an electric field distribution calculated for a multi-nozzle array (number of nozzles, tip-to-tip distance, and applied voltage) on the boundary condition of the single-nozzle GAME simulation model, multinozzle GAME was simulated; this enabled proposal of a spinnability diagram for stable spinning.