Polymerization of styrene in a continuous filled tubular reactor

Free radical solution polymerization of styrene has been studied using a binary mixture of symmetrical bifunctional initiators in a filled tubular reactor packed with static mixers. Owing to intensive radial mixing induced by the static mixers, a near plug flow pattern was obtained in the reactor with some axial dispersion effect. The axial mass dispersion coefficient was determined from the residence time distribution experiment and a dynamic axial dispersion model has been developed and solved to investigate steady state and transient behavior of the filled tubular reactor. With a solvent volume fraction of 0.3, the monomer conversion up to 70% was obtained without fouling problems in the temperature range 90 to 120°C. The experimental filled tubular reactor was operated under various reaction conditions and a reasonably good agreement between the model and the experimental data was obtained without using any adjustable parameters.     

Low‐temperature photoinitiation solution polymerization behavior of N‐vinylcarbazole in tetrahydrofuran

N‐Vinylcarbazole (VCZ) was solution‐polymerized in tetrahydrofuran (THF) at ?20, 0, and 20°C using the photoinitiation method; the effects of the amount of solvent, polymerization temperature, and photoinitiator concentration were investigated. On the whole, the experimental results corresponded to predicted ones. Low polymerization temperature using photoinitiation proved to be successful in obtaining poly(N‐vinylcarbazole) (PVCZ) of a high molecular weight with a smaller temperature rise during polymerization; nevertheless of free radical polymerization by 2,2′‐azobis(2,4‐dimethylvaleronitrile) (ADMVN). The photo‐solution polymerization rate of VCZ in THF was proportional to the 0.47 power of ADMVN concentration. The molecular weight was higher and the molecular weight distribution was narrower with PVCZ polymerized at lower temperatures. For PVCZ prepared in THF at ?20°C using a photoinitiator concentration of 0.00005 mol/mol of VCZ, a weight‐average molecular weight of 510,000 was obtained, with a polydispersity index of 1.73, and a degree of lightness converged to about 99%. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3667–3672, 2002     

Preparation and properties of polyimide/silica hybrid composites based on polymer‐modified colloidal silica

A new type of polyimide/silica (PI/SiO₂) hybrid composite films was prepared by blending polymer‐modified colloidal silica with the semiflexible polyimide. Polyimide was solution‐imidized at higher temperature than the glass transition temperature (T_g) using 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐diaminodiphenyl ether (ODA). The morphological observation on the prepared hybrid films by scanning electron microscopy (SEM) pointed to the existence of miscible organic–inorganic phase, which resulted in improved mechanical properties compared with pure PI. The incorporation of the silica structures in the PI matrix also increased both T_g and thermal stability of the resulting films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2053–2061, 2006     

Preparation and characterization of syndiotactic polystyrene/ethylene‐propylene copolymer blends

The reactive compatibilization of syndiotactic polystyrene (sPS)/oxazoline‐styrene copolymer (RPS)/maleic anhydride grafted ethylene‐propylene copolymer (EPR‐MA) blends is investigated in this study. First, the miscibility of sPS/RPS blends is examined by thermal analysis. The cold crystallization peak (T_cc) moved toward higher temperature with increased PRS, and, concerning enthalpy relaxation behaviors, only a single enthalpy relation peak was found in all aged samples. These results indicate that the sPS/RPS blend is miscible along the various compositions and RPS can be used in the reactive compatibilization of sPS/RPS/EPR‐MA blends. The reactive compatibilized sPS/RPS/EPR‐MA blends showed finer morphology than sPS/EPR‐MA physical blends and higher storage modulus (G') and complex viscosity (η*) when RPS contents were increased. Moreover, the impact strength of sPS/RPS/EPR‐MA increased significantly compared to sPS/EPR‐MA blend, and SEM micrographs after impact testing show that the sPS/RPS/EPR‐MA blend has better adhesion between the sPS matrix and the dispersed EPR‐MA phase. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2084–2091, 2002     

Synthesis and biological activity of phthalimide‐based polymers containing 5‐fluorouracil

The attachment of anticancer agents to polymers is a promising approach towards reducing the toxic side‐effects and retaining the potent antitumour activity of these agents. A new tetrahydrophthalimido monomer containing 5‐fluorouracil (ETPFU) and its homopolymer and copolymers with acrylic acid (AA) and with vinyl acetate (VAc) have been synthesized and spectroscopically characterized. The ETPFU contents in poly(ETPFU‐co‐AA) and poly(ETPFU‐co‐VAc) obtained by elemental analysis were 21 mol% and 20 mol%, respectively. The average molecular weights of the polymers determined by gel permeation chromatography were as follows: M_n = 8900 g mol^?1, M_w = 13 300 g mol^?1, M_w/M_n = 1.5 for poly(ETPFU); M_n = 13 500 g mol^?1, M_w = 16 600 g mol^?1, M_w/M_n = 1.2 for poly(ETPFU‐co‐AA); M_n = 8300 g mol^?1, M_w = 11 600 g mol^?1, M_w/M_n = 1.4 poly(ETPFU‐co‐VAc). The in vitro cytotoxicity of the compounds against FM3A and U937 cancer cell lines increased in the following order: ETPFU > 5‐FU > poly(ETPFU) > poly(ETPFU‐co‐AA) > poly(ETPFU‐co‐VAc). The in vivo antitumour activities of all the polymers in Balb/C mice bearing the sarcoma 180 tumour cell line were greater than those of 5‐FU and monomer at the highest dose (800 mg kg^?1). © 2002 Society of Chemical Industry     

Hydrodynamic characteristics of a FCC regenerator

The hydrodynamic and gas mixing characteristics have been determined in a FCC regenerator (0.48 m I.D.x3.4 m high) with FCC particles. Solids holdup in the dense bed decreases with increasing gas velocity, but it increases in the freeboard region. The bubble/void fraction increases with an increase along the bed height at a given gas velocity and increases with increasing gas velocity at a constant bed height. Backmixed tracer gas at the wall region is higher than that at the center region of the bed. The gas backmixing coefficient decreases with increasing gas velocity.     

Universal yield stress function for biocompatible chitosan based-electrorheological fluid: Effect of particle concentration

Electrorheological (ER) response of biocompatible particles suspended in an insulating silicone oil, was investigated under several different applied external electric field strengths. Chitosan, a biodegradable polysaccharide, was used as anhydrous ER materials. The effect of particle volume concentration on their ER response was examined by focusing on the measurement for rheological and electrical properties. The yield stress of chitosan suspended in silicone oil system as a function of applied electric field strength showed different value of slopes for different particle concentrations, however, all data points collapse onto a universal scaling function.     

A visual study on flame behavior in tone-excited non-premixed jet flames

A visualization study on the effect of forcing amplitude in tone-excited jet diffusion flames has been conducted. Visualization techniques are employed using optical schemes, which are a light scattering photography. Flame stability curve is attained according to Reynolds number and forcing amplitude at a fuel tube resonant frequency. Flame behavior is globally grouped into two from attached flame to blown-out flame according to forcing amplitude; one sticks the tradition flame behavior which has been observed in general jet diffusion flames and the other shows a variety of flame modes such as the flame of a feeble forcing amplitude where traditionally well-organized vortex motion evolves, a fat flame, an elongated flame, and an in-burning flame. Particular attention is focused on an elongation flame, which is associated with a turnabout phenomenon of vortex motion, and on a reversal of the direction of vortex roll-up. It is found that the flame length with forcing amplitude is the direct outcome of the evolution process of the formed inner flow structure. Especially the negative part of the acoustic cycle under the influence of a strong positive pressure gradient causes the shapes of the fuel stem and fuel branch part and even the direction of vortex roll-up to dramatically change.     

Effect of Antimony Addition on Electrical and Optical Properties of Tin Oxide Film

Antimony-doped tin oxide films were prepared on Corning glass substrate by chemical vapor deposition from a gas mixture of SnCl₄–SbCl₅–H₂O. The electrical conductivity and optical transmission of tin oxide films were studied with antimony doping. The film conductivity increased largely without losing optical transparency with a small addition of antimony. The increase of the conductivity was attributed mainly to more electrons donated by pentavalent Sb ions in the SnO₂ lattice. Large additions of antimony, however, diminished the conductivity, optical transparency, and crystallinity of the film. The diminution was found to be caused by fine Sb₂O₅ phases codeposited with SnO₂.     

Diffusional interference in liquid phase counter-adsorptions

A surface diffusion mocel with diffusional interference has been presented for the analysis of multicomponent adsorption of phenols by activated carbon. Surface diffusion coefficients for multicomponent adsorptions were estimated from the relationship between. the surface diffusion coefficient of each species and the surface coverage. The diffusional interference coefficients, W_ij, was determined from experimental counter-adsorption data. The numerical values of W_ij were in the range of 0.4–0.9, which show that the introduction of diffusional interference is necessary to analyze multicomponent counter-adsorptions properly. The proposed model successfully simulates the behaviour of phenols-activated carbon system in a batch adsorber.