Nonisothermal crystallization kinetics of poly(butylene terephthalate)/montmorillonite nanocomposites

The melt intercalation method was employed to prepare poly(butylene terephthalate) (PBT)/montmorillonite (MMT) nanocomposites, and the microstructures were characterized with X‐ray diffraction and transmission electron microscopy. Then, the nonisothermal crystallization behavior of the nanocomposites was studied with differential scanning calorimetry (DSC). The DSC results showed that the exothermic peaks for the nanocomposites distinctly shifted to lower temperatures at various cooling rates in comparison with that for pure PBT, and with increasing MMT content, the peak crystallization temperature of the PBT/MMT hybrids declined gradually. The nonisothermal crystallization kinetics were analyzed by the Avrami, Jeziorny, Ozawa, and Mo methods on the basis of the DSC data. The results revealed that very small amounts of clay (1 wt %) could accelerate the crystallization process, whereas higher clay loadings reduced the rate of crystallization. In addition, the activation energy for the transport of the macromolecular segments to the growing surface was determined by the Kissinger method. The results clearly indicated that the hybrids with small amounts of clay presented lower activation energy than PBT, whereas those with higher clay loadings showed higher activation energy. The MMT content and the crystallization conditions as well as the nature of the matrix itself affected the crystallization behavior of the hybrids. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3257–3265, 2006     

Preparation of narrowly distributed nanoparticles of poly(n‐butyl methacrylate‐co‐vinyl pyrrolidone) through microemulsion polymerization

Narrowly distributed nanoparticles of poly (n‐butyl methacrylate‐co‐vinyl pyrrolidone) were prepared through microemulsion polymerization with a nonionic surfactant of Tween‐80 as emulsifier (6 wt % of the latex) and n‐butanol as coemulsifier. The polymerizations were initiated with benzoylperoxide (BPO), potassium persulfate (KPS), KPS/ferric sulfate (FeSO₄), and BPO/FeSO₄, respectively, where the initiation in the case of BPO/FeSO₄ took place mainly at the interphase between the oil phase and the reaction media. Namely, this interfacial‐initiated microemulsion polymerization resulted in larger particles with relatively narrower particle size distribution as well as higher limiting monomer conversion but lower polymerization rate compared with the polymerization initiated with KPS/FeSO₄. In this article, the influences of initiation method, monomer ratio, and addition of water‐soluble components on microemulsion polymerization and latex particle size were studied to discuss the mechanism of interfacial‐initiated microemulsion polymerization. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2334–2340, 2004     

Effect of high polymerization temperature on the microstructure of isotactic polypropylene prepared using heterogeneous ticl4/mgcl2 catalysts

The effects of alkylaluminum and polymerization temperature on propylene polymerization without an external donor in the use of a TiCl₄–MgCl₂–diether(BMMF) catalyst were investigated. The results indicated that with increasing polymerization temperature the concentrations of [mmmm] of heptane‐insoluble poly(propylene) (PP) fraction increased. Crystallization analysis fractionation (CRYSTAF) results showed the fractions of different crystallization temperatures were changed according to various polymerization temperatures. The activity with Et₃Al as cocatalyst at 100°C was much lower than that at 70°C. However, the activity with i‐Bu₃Al at 100°C was as high as that at 70°C. The fraction of high‐crystallization temperature of PPs obtained with i‐Bu₃Al increased with increasing polymerization temperature, which was opposite to that with Et₃Al, thus implying that the copolymerization of propylene with the monomer arising from Et₃Al led to the lower crystallization ability of PPs obtained with Et₃Al. The terminal groups of PP suggested that the chain‐transfer reaction by β‐H abstraction was the main chain‐transfer reaction at 120°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3980–3986, 2003     

Preparation and properties of T300 carbon fiber‐reinforced thermoplastic polyimide composites

In this study, a series of T300 carbon fiber‐reinforced polyimide (CFRPI) composites were prepared by laminating premolding polyimide (PI) films with unidirectional carbon fiber (CF) layers. On the basis of PI systems design, the effect of CF volume fraction, processing conditions, and PI molecular structure on the properties of CFRPI composites was studied in detail. In addition, two kinds of nano‐particles, including carbon nano‐tube (CNT) and SiO₂ were filled into the premolding PI films with different concentrations. And the effect of nano‐particles on the properties of CFRPI composites was also investigated. The surface characteristic of T300 CF was measured by X‐ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). The properties of premolding PI film and CFRPI composites were measured by dynamic mechanical analysis (DMTA), SANS testing machine, scanning electron microscopy (SEM), and so forth. These experimental results showed that the properties of CFRPI composites were mainly affected by the premolding PI film and molding condition. The change of CF volume fraction from 55% to 65% took little effect on the mechanical properties of CFRPI composites. In addition, the incorporation of nano‐particle SiO₂ could further improve the properties of CFRPI composites, but CNT hardly improved the properties of CFRPI composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 646–654, 2006     

缩放管内CaCO_3污垢形成过程的数值模拟

利用从传热传质角度结合表面化学反应知识模拟CaCO3污垢形成过程的数学模型,对缩放管不同工况进行了数值模拟计算.得出不同工况下,缩放管内CaCO3污垢的沉积率、剥蚀率、污垢热阻随时间的变化规律以及它们与流速、工质浓度、温差的关系.     

Numerical simulation on the rheo-diecasting of the semi-solid A356 aluminum alloy

The effect of injection pressure, piston velocity, and the forming temperature of semisolid slurry on the filling behavior of the semi-solid A356 aluminum alloy was investigated by simulation methods. The simulation results show that these processing parameters have an important effect on the filling behavior of the semi-solid A356 aluminum alloy. The slurry flows steadily in the cavity when the injection pressure, the piston velocity, and the forming temperature are low, but it is prone to turbulent flow w...     

构建新形势下大学生党员发展质量保障体系

做好当代大学生党员发展工作是加强新形势下党的建设的重要举措。分析了目前高校大学生党员发展工作存在的问题,根据党建的有关原则和精神,提出了构建新形势下大学生党员发展质量保障体系的对策。     

高职旅游英语专业英语课程设置与人才培养

以ESP理论为指导,从旅游英语专业学生的学习需求及用人单位的人才规格需求出发,通过对高职旅游英语专业学生及用人单位设计的问卷访谈分析,解读旅游英语专业英语课程设置与人才培养的关系。     

Thermogravimetric analysis of methyl methacrylate‐graft‐natural rubber

The thermal degradations of methyl methacrylate‐graft‐natural rubber (MG) at different heating rates (B) in nitrogen were studied by thermogravimetric analysis. The results indicate that the thermal degradation of MG in nitrogen is a one‐step reaction. The degradation temperatures increase along with the increment of heating rates. The temperature of initial degradation (T₀) is 0.448B + 362.4°C, the temperature at maximum degradation rate, that is, the peak temperature on a differential thermogravimetric curve (T_p) is 0.545B + 380.7°C, and the temperature of final degradation (T_f) is 0.476B + 409.4°C. The degradation rate at T_p is not affected by B, and its average value is 48.9%; the degradation rate at T_f is not affected by B either, and its average value is 99.3%. The reaction order (n) is 2.1 and is not affected by B. The reaction activation energy (E) and the frequency factor (A) increase along with B, and the apparent reaction activation energy (E₀) is 254.6 kJ/mol. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2952–2955, 2002     

Porous poly(vinylidene fluoride) membrane with highly hydrophobic surface

The preparation of very hydrophobic poly(vinylidene fluoride) (PVDF) membranes was explored by using two methods. The first one was the modified phase inversion method using a water/N,N‐dimethylacetamide (DMAc) mixture instead of pure water as a soft precipitation bath. The second method was a precipitation‐bath free method, that is, the PVDF/DMAc casting solution underwent gelation in the open air instead of being immersed into a precipitation bath. The morphology of the surface and cross section of the membranes was investigated by using scanning electron microscopy (SEM). It was found that the membranes exhibited certain micro‐ and nanoscale hierarchical roughness on the surface, which brought about an enhanced hydrophobicity of the membrane. The contact angle (CA) of the samples obtained by the second method was as high as 150° with water. The conventional phase inversion method preparing PVDF porous membrane using pure water as precipitation bath usually results in an asymmetric membrane with a dense skin layer having a CA close to that of a smooth PVDF surface. The modified approach avoided the formation of a skin‐layer and resulted in a porous and highly hydrophobic surface of PVDF. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1358–1363, 2005