Massive transformation and absolute stability

Under carefully chosen conditions, solidification theory may be applied to solid-state transformations, and this has been done here for composition-invariant diffusion transformations. The predictions of the modeling are compared with isovelocity experiments in two iron systems, Fe-7.29 wt pct Cr and Fe-3.1 wt pct Ni. The ferrite to austenite phase transformation is used to demonstrate that stabilization of a planar transformation front at absolute stability is the natural lower velocity limit for a composition-invariant (massive) transformation. The results of the model, which includes nonequilibrium effects, clearly show that steady-state plane-front growth leading to composition invariance can be obtained at various temperatures depending on the growth velocity. In the lower velocity range, at the limit of absolute stability (of the order of 10 μm/s in the systems studied), the transformation interface moves under conditions of local equilibrium, and the temperature corresponds to the lower solvus temperature. At higher velocity (of the order of the interface diffusion rate, which in these systems is of the order of cm/s), the transformation is predicted to proceed at temperatures close to T ₀. At even higher rates, atom attachment kinetic undercooling will decrease the transformation temperature with respect to T ₀. In some cases, this temperature might even drop below the lower solvus. This article is based on a presentation made at the symposium entitled “The Mechanisms of the Massive Transformation,” a part of the Fall 2000 TMS Meeting held October 16–19, 2000, in St. Louis, Missouri, under the auspices of the ASM Phase Transformations Committee.     

Hardware and software architecture for power quality analysis

This paper presents a novel concept for power quality hardware and software architecture. Software tools related to detection, classification and characterization of power quality events can be integrated into a Distribution Control Center in which the interconnection between different subsystems is being carried out through the Internet allowing flexibility to the system. This system is implemented using wavelet analysis applied in all proposed algorithms. Different power quality events are taken as examples to illustrate the capabilities of the proposed method. The obtained results reveal that the proposed architecture is feasible to be implemented as an integral part of a control center system.The proposed system has the property of fast and accurate detection and classification of any power quality disturbance event and introduces a new PQ index determination that allows characterizing any type of disturbance including the non-periodic signals.     

Identification of thermoresistive solar radiation sensors

An identification procedure to estimate the parameters of a thermoresistive solar radiation sensor is presented. The proposed technique employs only electrical excitation for the sensor. The estimation algorithm is recursive and is applied to the sensor model derived from the thermodynamic equilibrium differential equations. The simulation and the experimental results demonstrate the validity of the proposed approach     

Morphological analysis of poly(o-methoxyaniline) thin-films deposited by spin coating technique

Morphological study of conducting polymer thin films obtained by spin coating is reported. Poly(o-methoxyaniline) films were deposited onto glass substrates and analyzed by profilometry and atomic force microscopy (AFM). It is shown that final thickness is correlated by a power law with spin speed with a solution concentration varying coefficient and that surface roughness decreases with increasing spin speed.     

Computer-controlled ion-selective electrode switch

The construction of a microcomputer-controlled electrode switch for use in potentiometric determinations is described. This can be coupled to most of the analytical equipment usually found in laboratories, to enable a setting up of automatic systems capable of performing sequential determinations with several ion-selective electrodes. The assessment of its analytical usage and behaviour are discussed.     

Production of single and multi-walled carbon nanotubes using natural gas as a precursor compound

In this work, the Catalytic Chemical Vapor Deposition (CCVD) technique was used to synthesize carbon nanotubes (CNT). Natural gas (NG) was employed as a carbon source for the growing of CNT, while magnesium oxide was used as a catalyst support for the nanotubes synthesis. Two systems were utilized. The Fe–Mo/MgO system was obtained by the impregnation technique through the dispersion of iron oxide, which is the catalyst, over magnesia (with molybdenum additions). This system was tested intending to optimize the parameters for the production of single-walled carbon nanotubes (SWCNT). Moreover, Mg_1−x Fe _x MoO₄, which was prepared by the combustion synthesis method, was tested to produce multi-walled carbon nanotubes (MWCNT). The Fe-Mo/MgO tests were carried out under H₂/GN and Ar/GN atmospheres at 950 °C, whereas the Mg_1−x Fe _x MoO₄ was submitted to 1,000 °C under H₂/GN atmosphere. The Fe–Mo/MgO catalyst produced better results regarding number of CNT and their diameters under Ar/NG atmospheres than under H₂/NG atmospheres. The system Mg_1−x Fe _x MoO₄ produced MWCNT according to the expectations.     

Localization by immunoelectron microscopy of Schistosoma mansoni antigens in the glomerulus of the hamster (Mesocricetus auratus) kidney

Gene therapy has the potential to provide cancer treatments based on novel mechanisms of action with potentially low toxicities. This therapy may provide more effective control of loco-regional recurrence in diseases such as non-small cell lung cancer (NSCLC), as well as systemic control of micrometastases. Despite current limitations, retroviral and adenoviral vectors can in certain circumstances provide an effective means of delivering therapeutic genes to tumour cells. Although multiple genes are involved in the process of carcinogenesis, mutations of the p53 gene are the most frequent abnormality identified in human tumours. Pre-clinical studies both in vitro and in vivo have shown that restoration of p53 function can induce apoptosis in cancer cells. Phase I clinical trials now show that p53 gene replacement therapy is feasible and safe using both retroviral and adenoviral vectors, and that it induces tumour regression in patients with advanced NSCLC and recurrent head and neck cancer. Other pre-clinical studies indicate that gene therapy may have useful synergy with cytotoxic and radiation therapy. This paper describes the different gene therapy strategies under investigation and the pre-clinical data that provides a rationale for the gene replacement approach, reviews clinical trial data and presents novel ideas for improving current vectors and gene delivery to tumours.