Determination of the solubility parameter of poly(ethylene oxide) at 25°C by gas-liquid chromatography

The solubility parameter of poly(ethylene oxide) at 25°C has been determined using the method developed by DiPaola-Baranyi and Guillet, by the extrapolation of the values of the interaction parameter χ, at high temperatures, ranging from 70°–90°, 90°–110° and 110°–130°C down to 25°C. The values of the solubility parameter obtained, depending on the temperature ranges employed, are 9.8, 9.9 and 10.1, respectively.     

Surface Areas of Nitrated Hydrotalcites

Hydrotalcites in the nitrate form were prepared using microwave irradiation in the hydrotreatment step. The surface area (BET) of nitrated hydrotalcites was evaluated. Solids were characterized by atomic absorption, X-ray diffraction and BET analysis. Thermal pretreatment temperature determined the surface area of the hydrotalcites.     

Near-Surface Deformation in an Alumina–Silicon Carbide-Whisker Composite due to Surface Machining

Deformation due to two different surface-machining conditions—grinding (126 μm diamond) and polishing (3 μm diamond)—in an uniaxial hot-pressed Al₂O₃–30%-SiC-whisker composite has been investigated. A Warren–Averbach analysis of grazing incidence X-ray diffractometry data shows that the deformation is localized to the very top surface zone. The cell size and the root mean square of the strain show a gradient in the deformed layer. Transmission electron microscopy studies, in cross-sectional view, also show a near-surface deformation zone containing dislocations, twins, and cracks. This is seen for both machining procedures, but the depth of the zone and the degree of deformation, in terms of dislocation density and number of cracks, is much higher in the roughly ground specimen than in the polished one. For comparison, a monolithic Al₂O₃ sample also has been studied after grinding. The deformation zone is very similar to the Al₂O₃–SiC sample with the same grinding condition, but cracks and dislocations are present at a slightly larger depth. The deformation depth for the polished Al₂O₃–SiC sample is ∼50 nm. In the ground Al₂O₃–SiC sample, the deformation depth is 1–1.5 μm and corresponds to the grain size. The deformation zone in the ground monolithic Al₂O₃ sample is 1.5–2 μm deep. The observed grain-boundary cracks are almost parallel to the surface and may originate from nonaccommodated plastic flow between grains.     

Analysis of pentasodium triphosphate hydration kinetics

The present work analyzes the effect of various factors on the hydration of pentasodium triphosphate. The experimental method is based on application of the hydration test. Technical-quality products with different proportions of phase I and phase II have been used. The variables studied are phase I/phase II ratio, initial temperature, particle size, stirring rate and composition of the slurry (presence of hexahydrate crystals and water hardness). The results have been discussed according to a kinetics model that includes a series of stages of a physical nature (dissolution of anhydrous salt and the crystallization of the hexahydrate), as well as of a chemical nature (solvation of the ions in solution). Crystallization of the hexahydrate may be the controlling stage in the process.     

Parameter Identification in Photothermal Imaging

We propose a technique to reconstruct the geometry of inclusions and their material parameters in thermal scattering near surfaces. The imaging problem is reformulated as a constrained optimization problem with a finite number of stationary constraints. The unknown domains and their parameters are the design variables. A descent method combining topological derivative analysis to find improved guesses of the objects and gradient iterations to correct their material parameters provides reasonable reconstructions.     

Functional properties of a protein product from Caryodendron orinocense (Barinas nut)

The functional properties of Caryodendron orinocense protein product were investigated and compared with those of soybean (Glycina maxima). The product protein content was 24.47 g/100 g (Nx6.25). Solubility increased at both sides of the isoelectric point (pH 4.0) and with increased NaCl concentration up to 0.5M. Compared with soybean flour (50% protein), the protein product exhibited higher water and oil absorption, but lower emulsifying activity, emulsion stability, foaming capacity, and foam stability, the last one increase at higher pH. Emulsifying activity, foaming capacity, and foam stability were ionic strength dependent. C. orinocense protein product increased its emulsifying activity steadily from 0.05M to 0.75M NaCl, while it remained almost constant for soybean flour. Foaming capacity increased drastically at pH 10. The minimum time and concentration to form a gel was 20% in 4 min and 10% in 8 min for the Caryodendron protein product and soybean flour, respectively. The bulk density was 0.5056+/-0.0041 g/mL.     

Coking kinetics of a Cr2O3/Al2O3 catalyst during 1-butene dehydrogenation: Effect of H2 partial pressure

The influence has been studied of the partial pressure of hydrogen (0–30 kPa) upon the coking rate of a Cr₂O₃/Al₂O₃ commercial catalyst during 1-butene dehydrogenation. Coke deposition has been analysed using a monolayer-multilayer reversible coke growth model (MMRC model). This model provides good fits to the experimental data, within the range of partial pressure of H₂ studied, and allows us to estimate the main kinetic parameters involved in the coking-deactivation process. The results obtained reveal a dual effect of hydrogen: competition against 1-butene for the active sites and the removal of coke precursors from the catalyst surface. Bom effects diminish the coking rate as the H₂ partial pressure is increased.     

Impregnation of X Zeolite with Alkaline Hydroxide During the Synthesis

Enhancement of the basic properties of the X zeolite with FAU framework has been carried out during synthesis, without further treatment such as ion-exchange or impregnation. Control of the washing stage enables retention of the optimum amount of alkaline hydroxides, which increases the basic catalytic activity of X zeolite in the alkylation of toluene. This alkaline hydroxides neither affect the FAU framework nor the silicon/aluminium molar ratio of the X zeolite. The optimum (Na + K)/Al molar ratio of the improved catalyst was 1.06 corresponding to a washing volume of 200 mL. This X zeolite presented better catalytic activity than a cesium-zeolite prepared by ion-exchange. The presence of hydroxysodalite impurity in the X zeolite increased the amount of impregnated alkaline hydroxides but not the catalytic activity. The present study shows that it is possible to increase the basic properties of the X zeolite directly in the synthesis process.     

A SIMPLE METHOD FOR STUDYING THE KINETICS OF GAS-SOLID REACTIONS IN A FLUIDIZED BED REACTOR

A methodology for studying the kinetics of gas-solid reactions in a fluidized bed reactor is presented. This procedure is based on the analysis of the response of the system (flue gases) when batches of solids of different weight are added to the reactor. The method has been applied to the study of limestone particle calcination. The calcination rate constants obtained are in good agreement with those found in the literature. The method offers the advantage of simplicity and avoids the use of model assumptions or empirical correlations.