Development of engineered cementitious composites with limestone powder and blast furnace slag

Nowadays limestone powder and blast furnace slag (BFS) are widely used in concrete as blended materials in cement. The replacement of Portland cement by limestone powder and BFS can lower the cost and enhance the greenness of concrete, since the production of these two materials needs less energy and causes less CO₂ emission than Portland cement. Moreover, the use of limestone powder and BFS improves the properties of fresh and hardened concrete, such as workability and durability. Engineered cementitious composites (ECC) is a class of ultra ductile fiber reinforced cementitious composites, characterized by high ductility, tight crack width control and relatively low fiber content. The limestone powder and BFS are used to produce ECC in this research. The mix proportion is designed experimentally by adjusting the amount of limestone powder and BFS, accompanied by four-point bending test and uniaxial tensile test. This study results in an ECC mix proportion with the Portland cement content as low as 15% of powder by weight. This mixture, at 28 days, exhibits a high tensile strain capacity of 3.3%, a tight crack width of 57 μm and a moderate compressive strength of 38 MPa. In order to promote a wide use of ECC, it was tried to simplify the mixing of ECC with only two matrix materials, i.e. BFS cement and limestone powder, instead of three matrix materials. By replacing Portland cement and BFS in the aforementioned ECC mixture with BFS cement, the ECC with BFS cement and limestone powder exhibits a tensile strain capacity of 3.1%, a crack width of 76 μm and a compressive strength of 40 MPa after 28 days of curing.     

Performance analysis of the domestic water meter park in water supply network of Ibarra,Ecuador

Apparent losses are one of the most important components of non-revenue water and mainly caused by water meter under-registration. This paper studies the performance of a water meter park from a developing country water utility in Ibarra city, Ecuador. The study includes three major aspects: water meter error curve reconstruction with seven different flow rates; water meter evaluation as a function of class, manufacturer and totalized registered volume, use of two water consumption patterns for weighted error determination and their influence on water balance and performance indicators analysis. Results indicate that 44% of analyzed meters works at optimal conditions. Weighted error obtained by using two different consumption patterns indicates a 0.95% difference, which has an important impact on water balance and performance indicator results. This detailed analysis of water meters can help to develop a more efficient water meter replacement strategy and to estimate apparent water loss volume more accurately.     

Short communication: Identification of Corynebacterium bovis by MALDI-mass spectrometry

Corynebacterium bovis is a mastitis-causing microorganism responsible for economic losses related to decrease in milk production. The aim of the study was identify Corynebacterium spp. strains recovered from milk samples of subclinical mastitis by using matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS). Samples were collected during a 10-mo mastitis-monitoring program in a high-production dairy farm. In this study, 80 strains were analyzed; from these 54 (67.5%) were identified at species level as Corynebacterium bovis, 24 (31.2%) isolates were identified at the genus level as Corynebacterium spp., and only 1 (1.35%) isolated had unreliable identification. Results demonstrated that MALDI-MS could be an important technique for the identification of Corynebacterium spp. in milk.     

Comparative analysis for power generation and ethanol production from sugarcane residual biomass in Brazil

This work compares the technical, economic and environmental (GHG emissions mitigation) performance of power generation and ethanol production from sugarcane residual biomass, considering conversion plants adjacent to a sugarcane mill in Brazil. Systems performances were simulated for a projected enzymatic saccharification co-fermentation plant (Ethanol option) and for a commercial steam-Rankine power plant (Electricity option). Surplus bagasse from the mill would be used as fuel/raw material for conversion, while cane trash collected from the field would be used as supplementary fuel at the mill. For the Electricity option, the sugarcane biorefinery (mill+adjacent plant) would produce 91 L of ethanol per tonne of cane and export 130 kWh/t of cane, while for the Ethanol option the total ethanol production would be 124 L/t of cane with an electricity surplus of 50 kWh/t cane. The return on investment (ROI) related to the biochemical conversion route was 15.9%, compared with 23.2% for the power plant, for the conditions in Brazil. Considering the GHG emissions mitigation, the environmentally preferred option is the biochemical conversion route: the net avoided emissions associated to the adjacent plants are estimated to be 493 and 781 kgCO₂eq/t of dry bagasse for the Electricity and Ethanol options, respectively.     

Functionalization of polydimethylsiloxane membranes to be used in the production of voice prostheses

Abstract

The voice is produced by the vibration of vocal cords which are located in the larynx. Therefore, one of the major consequences for patients subjected to laryngectomy is losing their voice. In these cases, a synthetic one-way valve set (voice prosthesis) can be implanted in order to allow restoration of speech. Most voice prostheses are produced with silicone-based materials such as polydimethylsiloxane (PDMS). This material has excellent properties, such as optical transparency, chemical and biological inertness, non-toxicity, permeability to gases and excellent mechanical resistance that are fundamental for its application in the biomedical field. However, PDMS is very hydrophobic and this property causes protein adsorption which is followed by microbial adhesion and biofilm formation. To overcome these problems, surface modification of materials has been proposed in this study. A commercial silicone elastomer, Sylgard^TM 184 was used to prepare membranes whose surface was modified by grafting 2-hydroxyethylmethacrylate and methacrylic acid by low-pressure plasma treatment. The hydrophilicity, hydrophobic recovery and surface energy of the produced materials were determined. Furthermore, the cytotoxicity and antibacterial activity of the materials were also assessed. The results obtained revealed that the PDMS surface modification performed did not affect the material's biocompatibility, but decreased their hydrophobic character and bacterial adhesion and growth on its surface.     

Economic design of water distribution systems in buildings

This article discusses an engineering optimization problem which arises in hydraulics and is related to the use of a new criterion for sizing water distribution piping in large buildings. The optimization model aims to find the most suitable interior pipe diameters for the various pipes in the system, using commercial sizes and minimizing the overall installation cost according to some boundary conditions. The problem is formulated as a non-convex nonlinear program and a branch-and-bound algorithm is introduced for its solution. A procedure is proposed to obtain a feasible solution with standard values from the optimal solution of the non-convex program. The performance of the algorithm is analysed for a real-life problem and the cost of the computed solution is assessed, showing the appropriateness of the model and the optimization techniques.     

Automatic control systems for submerged membrane bioreactors: a state-of-the-art review

Membrane bioreactor (MBR) technology has become relatively widespread as an advanced treatment for both industrial and municipal wastewater, especially in areas prone to water scarcity. Although operational cost is a key issue in MBRs, currently only a few crucial papers and inventions aimed to optimise and enhance MBR efficiency have been published. The present review summarises the available solutions in the area of automatic control systems and widely explores the advances in automation and control for MBRs. In this review of state of the art, different control systems are evaluated comparatively, distinguishing between control systems used for the filtration process and those used for the biological process of MBRs and describing the challenge faced by integrated control systems. The existing knowledge is classified according to the manipulated variables, the operational mode (open-loop or closed-loop) and the controlled variables used.     

SiC whisker reinforced multi-carbides composites prepared from B4C and pyrolyzed rice husks via reactive infiltration

SiC whisker reinfored carbide-based composites were fabricated by a reactive infiltration method by using Si as the infiltrate. Rice husks (RHs) were pyrolyzed to SiC whiskers, particles and amorphous carbon, and were then mixed with different contents of B₄C as well as Mo powders. The mixtures were molded to porous preforms for the infiltration. The SiC whiskers and particles in the preform remained in the composite. Molten Si reacted with the amorphous carbon, B₄C as well as Mo in the preform during the infiltration, forming newly SiC, B₁₂(C,Si,B)₃ as well as MoSi₂. The upper values of elastic modulus, hardness and fracture toughness of the composites are 297.8 GPa, 16.8 ± 0.8 GPa, and 3.8 ± 0.2 MPa m^1/2, respectively. The influence of the phase composition of the composites on the mechanical properties and the fracture mechanism are discussed.