On the hot-carrier-induced post-stress interface trap generation inn-channel MOS transistors

A continued fast interface trap generation is observed in n-channel MOS transistors after termination of the hot-carrier stress. The magnitude of this post-stress effect is strongly dependent on the conditions of the preceding stress, on the post-stress conditions and on the process parameters. For measurements at 293 K, a simple model is proposed which is based on the release of hydrogen by the thermal detrapping of holes, and which can explain the observed dependencies. The importance of the post-stress D_it-generation is illustrated for the case of dynamic stress conditions where it can lead to an apparently deviating degradation behavior     

Impurity Distribution Behavior in Caprolactam Extraction with Environmentally Benign Mixed Solvents

In a previous study a solvent mixture of heptane containing 40 mass % heptanol was selected as an alternative in the industrial extraction of caprolactam to replace benzene, toluene, or chlorinated hydrocarbons. This work reports the equilibrium distribution ratio of caprolactam and four model impurities of organic nature, namely, cyclohexanone, aniline, n‐methylcaprolactam, and cyclohexane‐carboxamide, comparing the mixed solvents with toluene as a reference. The resulting phase equilibria were interpreted using the equilibrium stage model. Based on these calculations it was found that, compared to toluene, the co‐extracted fraction of cyclohexanone and aniline was higher, that of n‐methylcaprolactam was comparable, and that of cyclohexane‐carboxamide was lower using the mixed solvent. Overall, the mixed solvent reduced the fraction of co‐extracted impurities by almost 10 %.     

Screening of supports for the immobilization of pectinmethylesterase from acerola (Malpighia glabra L)

A partially purified extract of pectinmethylesterase (PME) from acerola fruit was immobilized on various supports: glass, celite, chrysotile, agarose, concanavalin A Sepharose 4B, egg shell, polyacrylamide and gelatin. In addition, reticulation with glutaraldehyde was assessed, as well as the use of gelatin in the presence of celite, glass and silica. The highest immobilization yields were obtained when the pectinmethylesterase was immobilized in concanavalin A Sepharose 4B (81.7%) and in gelatin‐water (78.0%). Copyright © 2004 Society of Chemical Industry     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

High-performance surface-micromachined inchworm actuator

This work demonstrates a polycrystalline silicon surface-micromachined inchworm actuator that exhibits high-performance characteristics such as large force (/spl plusmn/0.5 millinewtons), large velocity range (0 to /spl plusmn/4.4 mm/sec), large displacement range (/spl plusmn/100 microns), small step size (/spl plusmn/10, /spl plusmn/40 or /spl plusmn/100 nanometers), low power consumption (nanojoules per cycle), continuous bidirectional operation and relatively small area (600 /spl times/ 200/spl mu/m/sup 2/). An in situ load spring calibrated on a logarithmic scale from micronewtons to millinewtons, optical microscopy and Michelson interferometry are used to characterize its performance. The actuator consists of a force-amplifying plate that spans two voltage-controlled clamps, and walking is achieved by appropriately sequencing signals to these three components. In the clamps, normal force is borne by equipotential rubbing counterfaces, enabling friction to be measured against load. Using different monolayer coatings, we show that the static coefficient of friction can be changed from 0.14 to 1.04, and that it is load-independent over a broad range. We further find that the static coefficient of friction does not accurately predict the force generated by the actuator and attribute this to nanometer-scale presliding tangential deflections.     

Analysis of the fluorescence of the ion Eu in fluoroborate glasses containing silver particles

We have studied theoretically and experimentally the fluorescence enhancement in fluoroborate glasses, doped with the ion Eu³⁺, containing small silver particles. The model developed shows that the gain coefficient has quenching and enhancement regions. The absorption peak of the metallic particles occurs at 425 nm, which is not in resonance with the ⁵L₆ level of the ion Eu³⁺. For this reason it is not possible to make a complete comparison between theoretical and experimental results, but the structure of the absorption spectra allows us to check some crucial aspects of the problem, such as energy transfer, enhancement of the local field and the high absorption by the particle system. Results of electronic microscopy have revealed non-uniformity of the particle distribution with average radii of approximately 20 Å and 35 Å and a measured localized mean filling factor of 0.02.     

Occurrence of the mycotoxins ochratoxin A, zearalenone and deoxynivalenol in feed components.

The mycotoxin contamination of feed components used by the Dutch cooperative feed industry was surveyed to estimate the risk for animal production losses. Of 89 randomly and 6 selectively taken samples of raw materials harvested in 1988 and 1989 27% were contaminated with ochratoxin A (OCHRA), 31% with zearalenone (ZEA) and 20% with deoxynivalenol (DON). The mean content (microgram/kg) of all positive randomly taken samples was 18 (OCHRA), 62 (ZEA) and 630 (DON). The highest level (microgram/kg) for all samples was 120 (OCHRA) in barley, 3100 (ZEA) in corn cob mix and 1900 (DON) in maizegluten feed. The results of this survey show that feed components are often contaminated with mycotoxins. However, the contamination level could only sporadically cause production losses in animal husbandry.     

Solubility of amaranth seed proteins in sodium sulphate and sodium chloride: the main factor in quantitative extraction for analysis

Nitrogen was extracted more efficiently from amaranth seed with 0.04 M Na₂SO₄ (5% w/v) than with either 0.09 M or 0.17 M NaCl (5% or 10% w/v), despite both solutions having the same ionic strength (μ= 1). Solubility of saline soluble proteins (albumin ± globulin) was very poor in either water or 1M NaCl, but increased in 0.4M NaCl at alkaline pH between 7 and 10. Globulins were very soluble in 0.4M NaCl at a pH 9. Albumin was the main storage protein. Saline soluble proteins formed very weak gels.