Analysis of the cooling capability of steam generators during the loss of residual heat removal system at midloop operation with closed primary system

Loss of residual heat removal system (RHRS) at midloop operation is one of the most significant core damage risk contributor at low power and shutdown conditions. During this kind of transients the reflux-condensation is one of the cooling mechanisms anticipated in the abnormal procedure of loss of RHRS at midloop level. In this sense, several simulations of loss of the RHRS with closed primary system with the TRACE V4.160 code have been performed considering different availability of steam generators. The present study aims to analyze the thermal-hydraulic behavior after the loss of RHRS at midloop conditions with the reflux-condensation as the only cooling mechanism available and to investigate the capability of this cooling mechanism. The simulation results show that one steam generator is sufficient to remove core decay heat of 11 MW obtaining an equilibrium pressure, but the core uncovery depends on the number of steam generators operating. Finally, an analysis of the abnormal procedure and the event trees of the loss of RHRS sequences at midloop operation has been performed taking into account the results obtained in the simulation with TRACE.     

Variation in Malting Quality and Heat Resistance in the Malting Barley Variety “Alexis”

In earlier studies concerning vigour, where subsamples are heat‐treated before germination there was found heat‐sensitive as well as heat‐resistant barley samples. The vigour model developed by Ellis and Roberts and further developed at Carlsberg, could only describe the heat‐sensitive barleys. Seventeen samples of the “Alexis” variety grown widely in Europe were collected from the EBC trials in 1994 in order to see if heat resistance in barley was influenced by different growing conditions. We found both heat‐sensitive samples following the vigour model as well as pronounced heat‐resistant samples, but these were not divided according to growing conditions. The germination curves dependent on heat treatment and germination time were evaluated by Principal Component Analysis (PCA). Heat‐resistant barley samples could be differentiated from heat‐sensitive samples already after ½ h of heat treatment at 68°C (12% moisture) and after 3 days of germination. The barley samples were analysed with regard to malting quality. The PCA evaluation of the data divided the samples according to growing location, mainly due to differences in protein and β‐glucan. However, the malting analyses could not describe the differences in heat resistance and sensitivity of the barleys. The biochemical background of the heat resistance found is discussed on the basis of literature. Our findings should give an experimental basis for exploiting a biochemical principle for heat resistance, which is formed during grain filling and consumed during storage and germination.     

Using artificial intelligence to model heavy plate mill rolling

This research summary discusses the application of neural networks, evolutionary strategies, and other artificial intelligence techniques in the modeling and optimization of the models used for temperature, rolling force, and torque calculation in heavy plate milling.     

A Study of Ozone Generation by Negative Corona Discharge Through Different Plasma Chemistry Models

The Steady radial distribution of chemical species in a wire‐to‐cylinder ozone generator filled with pure oxygen has been computed by applying four different plasma chemistry models of increasing complexity. The most complete model considers ten species (e, O₂ ⁺, O₂ ^?, O₃ ^?, O^?, O₂, O₂(¹Δ_g), O₂(¹∑_g ⁺), O and O₃) and 79 reactions, including ionization by electron impact, electron attachment and detachment, electron-ion recombination, charge transfer, etc. The chemical model is coupled with the electrical model through Poisson's equation. The spatially averaged ozone density has been computed as a function of the current intensity and compared with the experimental values obtained by UV spectroscopy.     

Characteristics of a NaOH-Activated Blast Furnace Slag Blended with a Fine Particle Silica Waste

Mortars of blast furnace slag blended with a geothermal silica waste at various replacement levels of 0%, 5%, 10%, 15%, and 20% were cured for up to 90 days. The binder was activated by 6 wt% Na₂O equivalent of sodium hydroxide. Lime was added as an activating agent and also to promote pozzolanic reaction with the silica. It was found that the presence of the silica waste increased the reactivity of the cementitious materials, as measured by means of nonevaporable water. The compressive strength was increased in the presence of the silica, except at the highest replacement level of 20%, the optimum silica replacement was that of 5%–10%. The microstructures of blended slag showed less porosity than those of neat slag mortars. The lime was completely consumed after 90 days of hydration.     

Design optimization of 3D steel structures: Genetic algorithms vs. classical techniques

In this paper an elitist genetic algorithm (GA) developed by the authors is compared with common commercial solutions for complex structural optimization. After its prior validation on two-dimensional (2D) structures, the GA was tuned and improved in order to obtain structural elements with minimum weights that satisfy the ultimate limit states of the applicable building code. Subsequently, the same spatial structures were optimized using a commercial structural analysis program. Finally, the cost and weight improvements obtained using the GA, although at a higher computational cost, are discussed.     

Downhole Upgrading of Extra-heavy Crude Oil Using Hydrogen Donors and Methane Under Steam Injection Conditions

An extra-heavy crude oil underground upgrading process is described which involves the downhole addition of a hydrogen donor additive under steam injection conditions (280-315°C and residence times of at least 24-h). Laboratory experiments showed a 4° increase in the API gravity (from 9 to 12°) of the upgraded product, a two-fold reduction in the viscosity and, an approximately 8% decrease in the asphaltene content with respect to the original crude. Further increases on the temperature led to products with improved properties reaching 15°API at 315°C. It was found that the presence of the natural formation (catalysts) and methane (natural gas) is necessary to enhance the properties of the upgraded crude oil. From GC and GC-MS results a reaction pathway is proposed that involves hydrogen transfers from tetralin to the extra-heavy crude oil resulting in the formation of 1,2-dihydronaphthalene. This compound is then transformed into naphthalene, further upgrading of crude oil through hydrogen donation. The results of the experiments carried out in the presence and absence of the mineral formation and with an inert solid (SiC) strongly indicate that the former acts as a catalyst and not as a heat transfer matrix. Isotopic labeling studies (CD₄ and ¹³CH₄) give evidences that, most probably, methane is involved in the upgrading reactions.     

Towards a new definition of EPOC parameters for anionic electrochemical catalysts: case of propene combustion

The electrochemical promotion of catalysis (EPOC) of propene combustion was investigated using Pt sputtered thin film on an O²⁻ conductor, 8 mol% Y₂O₃-stabilized-ZrO₂ (YSZ). In order to separate the influence of the thermal migration of the O²⁻ oxide ions from the electrolyte to the catalyst surface and the impact of an electrical polarization on the catalytic activity, several light-off experiments (cool down and heat up procedures) were successively performed under different polarizations, i.e. OCV, +2 and −2 V. These experiments have clearly shown that the presence of O²⁻ (thermally or electrochemically induced) inhibits the catalytic activity of the platinum for the propene deep oxidation. These results demonstrate the importance to define a normalized rate enhancement ratio, ρ _n , from a reference value of the catalytic rate corresponding to a Pt surface state free of O²⁻ ions.     

Inspection and Process of Tension of Cables of General Rafael Urdaneta Bridge

In 1997 and 1999, inspection works were carried out in the 384 cable stays of the six central piers of General Rafael Urdaneta Bridge, located in Maracaibo, Venezuela. Inspection indicated the presence of water and significant settlings in the sockets of the cables and corrosion along each cable and socket. The tension of the cables was also measured, and differences of up to 30% in the tension of the cables of some of the 24 groups corresponding to the six central piers (four groups of 16 for each pier) were found. The results suggested the need to retension the cables. This paper shows the outcome of the inspection and indicates the procedure and results of the process of retension, finished in July 2000.