Combustion of oil palm stone in a pilot-scale fluidised bed reactor

Biomass is being generated in vast amounts from oil palm plantations particularly in developing countries such as Malaysia, Thailand and Indonesia. Oil palm stone (OPS) is currently considered a waste material and has not previously been considered for energy purposes. The main objective of this study was to investigate the thermochemical conversion of OPS in a pilot-scale fluidised bed combustor. The net heating value of OPS was 24.93 MJ/kg. The effect of primary air flowrate and initial bed temperature were the main parameters investigated. The bed and bed's surface temperature were found to decrease as the primary air flowrate increased. In all tests CO emissions were less than 0.2%. The emissions of SO₂ and HCl ranged from 0.02 ppm to 0.05 ppm, significantly below the permitted levels set by legislation. Stable combustion was observed at a bed temperature of 950 °C. The most abundant elements found in the ash were Al, Ca, Fe, K, Mg, Mn, P, S and Si. However, due to the temperature regime used in the study fouling would not be an issue.     

Mechanisms of cement hydration

The current state of knowledge of cement hydration mechanisms is reviewed, including the origin of the period of slow reaction in alite and cement, the nature of the acceleration period, the role of calcium sulfate in modifying the reaction rate of tricalcium aluminate, the interactions of silicates and aluminates, and the kinetics of the deceleration period. In addition, several remaining controversies or gaps in understanding are identified, such as the nature and influence on kinetics of an early surface hydrate, the mechanistic origin of the beginning of the acceleration period, the manner in which microscopic growth processes lead to the characteristic morphologies of hydration products at larger length scales, and the role played by diffusion in the deceleration period. The review concludes with some perspectives on research needs for the future.     

Role of inertial lift in elutriating particles according to their density

A Reflux Classifier involves the liquid fluidization of particles into a set of parallel inclined channels. Closely spaced inclined channels promote a combination of laminar flow and a high shear rate, which in turn promote the elutriation of the particles according to their density. The hydrodynamics of the particle transport within the inclined channels was examined theoretically by combining established equations for describing the fluid flow, the terminal velocity of a particle, and the shear induced inertial lift, with no adjustable parameters. The theoretical calculations provided excellent agreement with a comprehensive experimental data set, demonstrating the significance of the inertial lift force that arises at a high shear rate under the condition of laminar flow. Complex features of the experimental data were described theoretically. This work explains how it is possible to elutriate particles according to their density, with the effects of particle size suppressed. A remarkable convergence of several criteria was found to be necessary for achieving the reported phenomena.     

Foam granulation: Liquid penetration or mechanical dispersion?

There have been significant advances in the understanding of wet granulation processes. Foam granulation is the latest development and an emerging area of interest for pharmaceutical manufacturing.Single foam penetration experiments were carried out on static powder beds, followed by short-nucleation experiments (where nuclei are formed by a nucleation-only mechanism) and full foam granulation experiments (where nucleation, growth and breakage are occurring simultaneously). All experiments were performed with lactose monohydrate powder using a 5 L high shear mixer–granulator. The foam penetration/dispersion behaviour was examined and the granule size distributions were investigated as a function of foam quality (83–97% FQ), impeller speed (105–515 rpm) and wet massing period (0–4 min).Nucleation in foam granulation is postulated to undergo either “foam drainage” or “mechanical dispersion” controlled mechanisms. For “foam drainage” mechanism, the foam penetrates the powder bed to form coarse and broad granule size distributions. For “mechanical dispersion” mechanism, the wetting and nucleation conditions are governed by the powder mixing conditions and similar granule size distributions are produced. Regardless of the mechanism, the initial wetting and nucleation behaviour controls the initial nuclei size distribution, and this initial distribution is retained in the final granule size distribution. This work demonstrated the critical importance of the nucleation and binder distribution in determining the granule size distributions for foam granulation process.     

Synthesis and structure-activity relationship of the isoindolinyl benzisoxazolpiperidines as potent,selective, and orally active human dopamine D4 receptor antagonists

A new class of potent dopamine D(4) antagonists was discovered with selectivity over dopamine D(2) and the alpha-1 adrenoceptor. The lead compound was discovered by screening our compound collection. The structure-activity relationships of substituted isoindoline rings and the chirality about the hydroxymethyl side chain were explored. The isoindoline analogues showed modest differences in potency and selectivity. The S enantiomer proved to be the more potent enantiomer at the D(4) receptor. Several analogues with greater than 100-fold selectivity for D(4) over D(2) and the alpha-1 adrenoreceptor were discovered. Several selective analogues were active in vivo upon oral or intraperitoneal administration. A chiral synthesis starting from either D- or L-O-benzylserine is also described.     

A Fast XPS Study of Propene Decomposition over Clean and Sulphated Pt{111}

The thermal decomposition of propene over clean and sulphate precovered Pt{111} has been followed by Fast XPS. The saturation propene coverage over the clean surface is 0.21 mL at 90 K. Propene is stable up to 200 K, above which molecular desorption and dehydrogenation result in the formation of a stable propylidyne intermediate adlayer at 300 K. Propylidyne decomposes above 400 K eventually forming graphitic carbon above 800 K. Preadsorbed surface sulphate promotes room temperature propene combustion associated with the decomposition of a thermally unstable alkyl--sulphate complex. Propylidyne also forms as on clean Pt{111}, but is less reactive, its decomposition above 450 K triggering partial oxidation with residual surface oxygen to liberate gas phase CO.     

An improved accelerated weathering protocol to anticipate Florida exposure behavior of coatings

A new accelerated weathering protocol has been developed which closely replicates the performance of automotive and aerospace coating systems exposed in South Florida. IR spectroscopy was used to verify that the chemical composition changes that occurred during accelerated weathering in devices with a glass filter that produced a high fidelity reproduction of sunlight’s UV spectrum matched those that occurred during natural weathering. Gravimetric water absorption measurements were used to tune the volume of water absorption during accelerated weathering to match that which occurred during natural weathering in South Florida. The frequency of water exposure was then scaled to the appropriate UV dose. A variety of coating systems were used to verify the correlation between the physical failures observed in the accelerated weathering protocol and natural weathering in South Florida. The new accelerated weathering protocol correctly reproduced gloss loss, delamination, cracking, blistering, and good performance in a variety of diverse coating systems. For automotive basecoat/clearcoat paint systems, the new weathering protocol shows significant acceleration over both Florida and previous accelerated weathering tests. For monocoat aerospace systems, the new weathering protocol showed less acceleration than for automotive coatings, but was still an improvement over previous accelerated tests and was faster than Florida exposure.     

Dietary Intake and Food Sources of EPA, DPA and DHA in Australian Children

Secondary analysis of the 2007 Australian National Children’s Nutrition and Physical Activity survey was undertaken to assess the intake and food sources of EPA, DPA and DHA (excluding supplements) in 4,487 children aged 2–16 years. An average of two 24-h dietary recalls was analysed for each child and food sources of EPA, DPA and DHA were assessed using the Australian nutrient composition database called AUSNUT 2007. Median (inter quartile range, IQR) for EPA, DPA and DHA intakes (mg/day) for 2–3, 4–8, 9–13, 14–16 year were: EPA 5.3 (1.5–14), 6.7 (1.8–18), 8.7 (2.6–23), 9.8 (2.7–28) respectively; DPA 6.2 (2.2–14), 8.2 (3.3–18), 10.8 (4.3–24), 12.2 (5–29) respectively; and DHA 3.9 (0.6–24), 5.1 (0.9–26), 6.8 (1.1–27), 7.8 (1.5–33) respectively. Energy-adjusted intakes of EPA, DPA and DHA in children who ate fish were 7.5, 2 and 16-fold higher, respectively (P < 0.001) compared to those who did not eat fish during the 2 days of the survey. Intake of total long chain n-3 PUFA was compared to the energy adjusted suggested dietary target (SDT) for Australian children and 20 % of children who ate fish during the 2 days of the survey met the SDT. Fish and seafood products were the largest contributors to DHA (76 %) and EPA (59 %) intake, while meat, poultry and game contributed to 56 % DPA. Meat consumption was 8.5 times greater than that for fish/seafood. Australian children do not consume the recommended amounts of long chain omega-3 fatty acids, especially DHA, which could be explained by low fish consumption.     

Reactions of glycerol with poly(ethylene ether carbonate) polyols

Poly(ethylene ether carbonate) polyols can be modified by chemical reactions with polyglycol modifiers under conditions of elevated temperatures and reduced pressures. The modifier becomes chemically incorporated into the modified polyol and is used to control properties such as moisture sensitivity, CO₂ content, T_g, density, etc. in the resultant polyol. However, glycerol cannot be used as a modifier for poly(ethylene ether carbonate) polyols under the same conditions since it reacts with poly(ethylene ether carbonate) polyols by a transesterification reaction sequence to form glyceryl carbonate. As the temperature is increased, the glyceryl carbonate decomposes to yield glycidol and carbon dioxide. These reactions are conveniently followed by ¹³C-NMR. The preparation of glyceryl carbonate by this process has not been previously reported.     

Tailoring Encodable Lanthanide‐Binding Tags as MRI Contrast Agents

Lanthanide‐binding tags (LBTs), peptide‐based coexpression tags with high affinity for lanthanide ions, have previously been applied as luminescent probes to provide phasing for structure determination in X‐ray crystallography and to provide restraints for structural refinement and distance information in NMR. The native affinity of LBTs for Gd³⁺ indicates their potential as the basis for engineering of peptide‐based MRI agents. However, the lanthanide coordination state that enhances luminescence and affords tightest binding would not be ideal for applications of LBTs as contrast agents, due to the exclusion of water from the inner coordination sphere. Herein, we use structurally defined LBTs as the starting point for re‐engineering the first coordination shell of the lanthanide ion to provide for high contrast through direct coordination of water to Gd³⁺ (resulting in the single LBT peptide, m‐sLBT). The effectiveness of LBTs as MRI contrast agents was examined in vitro through measurement of binding affinity and proton relaxivity. For imaging applications that require targeted observation, fusion to specific protein partners is desirable. However, a fusion protein comprising a concatenated double LBT (dLBT) as an N‐terminal tag for the model protein ubiquitin had reduced relaxivity compared with the free dLBT peptide. This limitation was overcome by the use of a construct based on the m‐sLBT sequence (q‐dLBT–ubiquitin). The structural basis for the enhanced contrast was examined by comparison of the X‐ray crystal structure of xq‐dLBT–ubiquitin (wherein two tryptophan residues are replaced with serine), to that of dLBT‐ubiquitin. The structure shows that the backbone conformational dynamics of the MRI variant may allow enhanced water exchange. This engineered LBT represents a first step in expanding the current base of specificity‐targeted agents available.