Impact of variable frequency microwave and rapid thermal sintering on microstructure of inkjet-printed silver nanoparticles

The effect of thermal profile on microstructure is studied in the frame of thin films deposited by inkjet-printing technology. The role of sintering temperature and thermal ramp is particularly investigated. Fast heating ramps exhibit coarse grains and pores, especially when a hybrid microwave curing is performed. This enhanced growth is attributed to the quick activation of densifying sintering regimes without undergoing thermal energy loss at low temperature. Microstructural evolution of various sintered inkjet-printed films is correlated with electrical resistivity and with the Young’s modulus determined by nanoindentation. A strong link between those three parameters is highlighted during experiments giving credit to either a surface or a fully volumetric sintering, according to the process. Sintering is then mainly triggered by surface mass transfer or by grain boundary diffusion. Silver thin films with an electrical resistivity 4–5 times higher than the bulk, has been reached in a few minutes with a Young’s modulus of 38?GPa.     

Retardation of High-Temperature Fuel Ash Corrosion of Fireside Boiler Tubes via Nanoparticles

The high-temperature corrosion rate of boiler tubes was studied as a function of inhibitor concentration, time, and temperature in the absence and presence of fuel ash. Samples of steel tubes were taken from boilers that operate in Northern Baghdad Station for Electric Power Generation. Fuel ash was collected from the boiler combustion chamber, as well. Normal and nano-MgO were used as a corrosion inhibitor in different mixing ratios. A weight loss technique was used to evaluate the corrosion rates, while scanning electron microscopy was used to study the surface morphology. It was seen that corrosion rates increased with both time and temperature, and decreased with the addition of inhibitors. The maximum inhibitor efficiency was 81 %, obtained via using nano-MgO at mixing weight ratio 2:1, 600 °C, and 10 h. The Presence of fuel ash had harmful effects on the steel surface.     

Isolation and characterisation of collagen from the ribbon jellyfish (Chrysaora sp.)

Pepsin‐solubilised collagen from the ribbon jellyfish (Chrysaora sp., morphotype 1) umbrella (JPSC) was isolated and characterised. The yield of collagen varied (9–19%, based on ash‐free dry weight) depending on the amount of pepsin used. Type II collagen was the major component of extracted collagen. The peptide map of JPSC differed from that of standard collagen type II, which indicates their different primary structures. FTIR spectra of JPSC, however, did not differ significantly from those of type II collagen. The T_max of JPSC was 37.38 °C, which is higher than that of other marine collagens. Glycine was the main amino acid in JPSC (320 residues per 1000 residues), followed by glutamic acid, alanine, proline, aspartic acid and hydroxyproline. The isoelectric point of JPSC was 6.64. These results indicate that this jellyfish species has the potential to be a marine source of type II collagen that can be used in place of land‐based sources.     

Resistance of exterior three-dimensional walls to high velocity projectiles

There have been a number of recent civilian deaths due to ammunition from commonly used firearms penetrating exterior walls of residential, public, and commercial buildings. Experimental research was conducted to study the behavior of three-dimensional (3D) exterior walls when subjected to high velocity projectiles or bullets fired from a variety of firearms of different calibers. Four types of firearms were used, namely, a 9 mm gun, a 0.357 Magnum gun, an M16 machine gun, and a 7.62 Clashin Koff machine gun. The size of chips and the depth of penetrations produced by the fired bullets are documented and discussed. It was found that none of the fired bullets penetrated the two reinforced concrete layers of the exterior wall. In conclusion, 3D exterior walls provide an acceptable level of protection from ammunition fired from commonly used firearms.     

Multistage bayesian autonomy for high‐precision operation in a large field

This paper presents a generalized multistage bayesian framework to enable an autonomous robot to complete high‐precision operations on a static target in a large field. The proposed framework consists of two multistage approaches, capable of dealing with the complexity of high‐precision operation in a large field to detect and localize the target. In the multistage localization, locations of the robot and the target are estimated sequentially when the target is far away from the robot, whereas these locations are estimated simultaneously when the target is close. A level of confidence (LOC) for each detection criterion of a sensor and the associated probability of detection (POD) of the sensor are defined to make the target detectable with different LOCs at varying distances. Differential entropies of the robot and target are used as a precision metric for evaluating the performance of the proposed approach. The proposed multistage observation and localization approaches were applied to scenarios using an unmanned ground vehicle (UGV) and an unmanned aerial vehicle (UAV). Results with the UGV in simulated environments and then real environments show the effectiveness of the proposed approaches to real‐world problems. A successful demonstration using the UAV is also presented.     

Novel composite membrane based on zirconium phosphate-ionic liquids for high temperature PEM fuel cells

Composite membranes composed of zirconium phosphate (ZrP) and imidazolium-based ionic liquids (IL), supported on polytetrafluoroethylene (PTFE) were prepared and evaluated for their application in proton exchange membrane fuel cells (PEM) operating at 200 °C. The experimental results reported here demonstrate that the synthesized membrane has a high proton conductivity of 0.07 S cm^?1, i.e, 70% of that reported for Nafion. Furthermore, the composite membranes possess a very high proton conductivity of 0.06 S cm^?1 when processed at 200 °C under completely anhydrous conditions. Scanning electron microscopy (SEM) images indicate the formation of very small particles, with diameters in the range of 100–300 nm, within the confined pores of PTFE. Thermogravimetric analysis (TGA) reveals a maximum of 20% weight loss up to 500 °C for the synthesized membrane. The increase in proton conductivity is attributed to the creation of multiple proton conducting paths within the membrane matrix. The IL component is acting as a proton bridge. Therefore, these membranes have potential for use in PEM fuel cells operating at temperatures around 200 °C.