Influence of Manufacturing and Ripening Conditions on the Survival of Enterobacteriaceae in Manchego Cheese

The effects of cooking temperature, time and temperature of brine-salting, and temperature of ripening on the behavior of Enterobacteriaceae in Manchego cheese were studied. Fifty lots of cheese from raw ewe's milk manufactured and ripened under different conditions were investigated throughout a 60-day ripening period. Differences in pH values due to temperature-dependent whey retention accounted for the effect of cooking temperature on coliform and fecal coliform counts. Temperature of brine-salting had no effect on Enterobacteriaceae counts, but a significant effect of salting time on Enterobacteriaceae and fecal coliform counts was detected. Ripening temperature was the manufacturing variable with greatest influence (P<.01) on Enterobacteriaceae and coliform counts during the whole curing period.     

Analysis of the propagation of leaky magnetostatic modes in normally magnetized microstrip and slot lines

The propagation of leaky forward magnetostatic (MS) volume waves along ferrite-loaded microstrip and slot lines is analyzed. This phenomenon is studied by means of a numerical approach based on the residue calculus technique because of its good numerical convergence and stability. The proposed method allows for a quick and accurate computation of the phase and attenuation constants of the leaky MS modes. A comparative analysis between both microstrip lines and slot lines is carried out, and some new physical effects, such as MS resonances in the radiation loss, are reported. The advantages of the proposed method of analysis over other numerical methods, such as Galerkin's or moment methods, are also discussed.     

Ti/Al Interaction and Austenite Grain Control in Crankshaft Manufacturing with 38MnSiVS5 Steel

38MnSiVS5 steel is similar to 38MnVS6 steel (EN), the difference being the addition of a small Ti content. Typical Ti and Al contents in the chemical composition of 38MnSiVS5 steel are Ti=0.020 and Al=0.035 mass%. Both elements combine easily with nitrogen, especially Ti, and it has been observed that relatively high Al levels are harmful for austenite grain size control at reheating temperatures. In this work 38MnSiVS5 steel is used to manufacture a large number of castings, varying only the Ti and Al contents and obtaining ingots with a different Ti/Al ratio in each case. The results show that abnormal growth of the austenitic grain occurs irrespective of the Ti and Al contents, due fundamentally to the partial dissolution and coarsening of TiN precipitates. However, the steels with high Al contents present worse behaviour due to the formation of a second type of precipitates, namely AIN, which quickly dissolve between 1000 and 1100°C, causing a drastic decline in local pinning forces that gives rise to more pronounced abnormal growth of the affected grains.     

Effect of polyethylene on osteocalcin, alkaline phosphatase and procollagen secretion by human osteoblastic cells

BACKGROUND AND STUDY AIMS: Anastomotic leakage is a severe complication in gastric surgery and it is associated with a high rate of mortality. Conservative treatment sometimes is not sufficient to stem the leakages and, even when it is sufficient, it takes a long time. The present study describes the first experience in the treatment of anastomotic leakages with endoscopic clipping. PATIENTS AND METHODS: From May 1995 to December 1996, seven patients with postoperative anastomotic leakages after gastric surgery were prospectively treated in our Endoscopy Service. Metallic endoclips (MD 850, Olympus Corp., Tokyo, Japan) with prongs 12 mm long and 6 mm wide were applied, controlling the closure of the leakage by endoscopy, using radiographs to confirm the closure 24 hours later. RESULTS: Complete closure of the leakage was obtained in all seven cases. A single session of endoscopic clipping was needed for five patients while two other required, respectively, two and three sessions. The median time of leakage closure after endoscopic clipping was 2.3 days (range 1-5 days). The clips spontaneously dislodged within 1 month in five patients and within the second month in the other two patients. CONCLUSION: Endoscopic treatment of anastomotic leakages by metallic clips represents a safe and easily repeated method and, compared to conservative treatment, it seems to offer several time and cost advantages. Further studies involving a larger number of patients are needed to verify this finding.     

Proton nuclear magnetic resonance rapid and structure-specific determination ofω-3 polyunsaturated fatty acids in fish lipids

Based on proton nuclear magnetic resonance (¹H-NMR) spectroscopy, a rapid and structure-specific method for the determination of ω-3 polyunsaturated fatty acids (PUFAs) in fish lipids is presented. The different chemical shift observed for the methyl resonance of ω-3 PUFAs (δ=0.95 ppm) with respect to the methyl resonance of all other fatty acids (δ=0.86 ppm) has provided the possibility of proposing a new and rapid method for the determination of ω-3 PUFA content. Twenty-four fish lipid samples (raw, cooked and canned albacore tuna) produced results that showed good agreement between¹H-NMR analysis and gas chromatographic determination. Raw and cooked samples showed significantly higher levels of ω-3 PUFA than canned tuna.     

Hausen and Murphree efficiencies in binary and multicomponent distillation

The design of industrial distillation columns is normally based on estimated values of plate efficiencies. Several different plate efficiency models have been proposed in the literature and among them the one presented by Murphree is widely used in spite of its limitations. However the difficulties involved in the use of Murphree's model are not present if Hausen's model is considered.In the present paper a comparative study of the two models considering both binary and multicomponent systems is presented. A graphical relationship beExperimental composition profiles obtained in small laboratory columns with binary and ternary systems are interpreted in terms of Hausen efficiencies.It is argued that the use of the Hausen efficiency model should be wider as it overcomes limitations of Murphree's model and is in agreement with physi     

A novel microneedle array for the treatment of hydrocephalus

We present a microfabricated 10 by 10 array of microneedles for the treatment of a neurological disease called communicating hydrocephalus. Together with the previously reported microvalve array, the current implantable microneedle array completes the microfabricated arachnoid granulations (MAGs) that mimic the function of normal arachnoid granulations. The microneedle array was designed to enable the fixation of the MAGs through dura mater membrane in the brain and thus provide a conduit for the flow of cerebrospinal fluid. Cone-shaped microneedles with hollow channels were fabricated using a series of microfabrication techniques: SU-8 photolithography for tapered geometry, reactive ion etching for sharpening the microneedles, 248 nm deep UV excimer laser machining for creating through-hole inside the microneedles, and metal sputtering for improved rigidity. Puncture tests were conducted using porcine dura mater and the results showed that the fabricated microneedle array is strong enough to pierce the dura mater. The in vitro biocompatibility test result showed that none of the 100 outlets of the microneedles exposed to the bloodstream were clogged significantly by blood cells. We believe that these test results demonstrate the potential use of the microneedle array as a new treatment of hydrocephalus.     

Eicosapentaenoic acid (20∶5n-3) from the marine microalgaPhaeodactylum tricornutum

Eicosapentaenoic acid (EPA, 20∶5n-3) was obtained from the marine microalgaePhaeodactylum tricornutum by a three-step process: fatty acid extraction by direct saponification of biomass, polyunsaturated fatty acid (PUFA) concentration by formation of urea inclusion compounds, and EPA isolation by semipreparative high-performance liquid chromatography (HPLC). Alternatively, EPA was obtained by a similar two-step process without the PUFA concentration step by the urea method. Direct saponification of biomass was carried out with two solvents that contained KOH for lipid saponification. An increase in yield was obtained because the problems associated with emulsion formation were avoided by separating the biomass from the soap solution before adding hexane for extraction of insaponifiables. The most efficient solvent, ethanol (96%) at 60°C for 1 h, extracted 98.3% of EPA. PUFA were concentrated by the urea method with a urea/fatty acid ratio of 4∶1 at a crystallization temperature of 28°C and by using methanol and ethanol as urea solvents. An EPA concentration ratio of 1.73 (55.2∶31.9) and a recover yield of 78.6% were obtained with methanol as the urea solvent. This PUFA concentrate was used to obtain 93.4% pure EPA by semipreparative HPLC with a reverse-phase, C₁₈, 10 mm i.d.×25-cm column and methanol/water (1% acetic acid), 80∶20 w/w, as the mobile phase. Eighty-five percent of EPA loaded was recovered, and 65.7% of EPA present inP. tricornutum biomass was recovered in highly pure form by this three-step downstream process. Alternatively, 93.6% pure EPA was isolated from the fatty acid extract (without the PUFA concentration step) with 100% EPA recovery yield. This two-step process increases the overall EPA yield to 98.3%, but it is only possible to obtain 20% as much EPA as that obtained by three-step downstream processing.