Hydroxyapatite crystal growth on calcium hydroxyapatite ceramics

Calcium hydroxyapatite (Ca-HAP) ceramics containing tricalcium phosphate (TCP) were soaked in three solutions: phosphate buffer, tris buffer, and simulated body fluid (SBF). Petal-like crystals of Ca-HAP were deposited on the Ca-HAP ceramics when (i) Ca-HAP ceramics contained -TCP, (ii) the soaking solution contained phosphate ion and (iii) the pH of soaking solution was higher than 7.3. These conditions facilitate the presence of HPO ₄ ^2– and Ca²⁺ ions, the latter from dissolution of -TCP. A well-defined X-ray diffraction pattern for the deposited Ca-HAP crystals indicates preferred growth of {002} planes. Slower crystal growth of Ca-HAP was found for SBF (pH=7.5) than in the phosphate buffer, due possibly to the lower phosphate ion content in SBF.     

Principle and operation of a new type motor consisting of piezoelectric device and strain wave gearing

The authors have developed a new type of motor consisting of a piezoelectric device and strain wave gearing, and is called a piezoelectric motor. This is a first step in realizing a low-speed, small-size and lightweight motor. The principle of the motor is that the traveling wave is produced by piezoelectric devices and displacement conversion devices without mechanical resonance, and the torque to rotate the motor is generated by a mechanism of strain wave gearing (circular spline and flexspline) without using friction. The motor is operated at variable frequency and its rotational position (angle) is controlled in open-loop because it is basically a synchronous motor. In this paper, the structure and principle of the proposed motor are explained and the driving method and the mechanical characteristics of an experimental motor also are described. The results are as follows:

• 1 The realizability of the proposed piezoelectric motor is verified experimentally. The experimental motor operates at 2920 steps per revolution, and its speed range is 0 to 960 pps [or 0 to 20 (rpms)].
• 2 The torque characteristics are clarified qualitatively.
• 3 The generated torque of the experimental motor is small (less than 0.03 Nm) and therefore the improvement of the torque is an important subject hereafter.
• 4 It is possible to construct the motor with nonmetallic material. This fact is considered to facilitate obtaining a means to lighten the weight of the motor in the future.

     

Sorption and diffusion of ionic dyes in anionic cellophane membranes

Experimental steady-state permeability studies have been made with non-ionic, anionic and cationic dyes using carboxy cellulose membranes as anionic substrates. The experimental results show that with increasing bulk ionic strength the diffusion velocities of anionic and cationic compounds increase and decrease, respectively. The diffusion behavior of non-ionic compounds is independent of the ionic strength. Empirical relationships have been deduced which fit the permeation data of the anionic compounds. A new concept is introduced which postulates that the diffusion behavior of colons within an anionic membrane is dependent on the basicity of the fixed ionic groups. In substrates with matrix-bound anionic groups of high basicity, such as carboxy cellulose, the permeability behavior is described in terms of a new diffusion mechanism referred to as the “fluctuating” charge mechanism. This concept can provide a semi-quantitative understanding of the different electrostatic obstruction effects which matrix-bound carboxylate and sulfonate groups have on the permeability of colons. The measured permeability of the counter ions is in qualitative agreement with the proposed diffusion model.     

Impregnation of silk sericin into polyester fibers using supercritical carbon dioxide

Silk sericin was impregnated into polyester fabric using supercritical carbon dioxide (SCCO₂) to overcome polyester hydrophobicity. The effects of sericin molecular weight, pH of sericin, solution and cosolvent types on sericin impregnation were investigated. Enzyme‐hydrolyzed, acid‐, based‐hydrolyzed sericin in SCCO₂, and a 30 kDa sericin in SCCO₂ modified with cosolvents such as water, methanol, 1‐propanol, and acetone; and a modifier: sodium hydroxide solution were used in this work. Impregnation of sericin in polyester was indicated by Fourier transform infrared spectrophotometry (FTIR) and dyeing with acid dye. Degradation of polyester fibers during SCCO₂ process was indicated by scanning electron microscopy (SEM). Methylene blue dyeing was used to realize carboxyl group in polyester. The results showed no impregnation of sericin into polyester by using SCCO₂ modified with cosolvents. However, sericin was impregnated into modified surface polyester since hydrophilic groups such as carboxyl and hydroxyl groups were regenerated by alkaline hydrolysis. Samples impregnated with hydrolyzed sericin showed high color strength of Supranolechtbordeaux B acid dye. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Redox properties of CeO2 and Pt-Rh/CeO2 studied by TAP method

Redox properties of CeO₂ and Pt-Rh/CeO₂ were studied by temporal analysis of products (TAP) method using alternative pulses of CO and O₂. A portion of pulsed CO was oxidized to CO₂ and a portion of CO was adsorbed on the surface. Pulsing ¹⁸O₂ onto the catalyst which has surface species derived from CO, evolved CO₂ contained no ¹⁸O suggesting that the surface species will be carbonate ions.     

Improvement of Pt/ZrO2 by CeO2 for high pressure CH4/CO2 reforming

CH₄/CO₂ reforming over Pt/ZrO₂, Pt/CeO₂ and Pt/ZrO₂ with CeO₂ was investigated at 2 MPa. Pt/ZrO₂, which shows stable activity under 0.1 MPa, and Pt/CeO₂ showed gradual deactivation with time at the high pressure. The deactivation was suppressed drastically on Pt/ZrO₂ with CeO₂ prepared by different impregnation order (co-impregnation of Pt and CeO₂ on ZrO₂, and consecutive impregnation of Pt and CeO₂ on ZrO₂). The amount of coke deposition was found insignificant and similar among all the catalysts (including Pt/ZrO₂ and Pt/CeO₂). Catalytic activity after the reaction for 24 h was in agreement with Pt particle size after the reaction for same period, indicating that the difference of the catalytic stability is mainly dependent on the extent of Pt aggregation through catalyst preparation, H₂ reduction, and the CH₄/CO₂ reforming. Pt aggregation and the amount of coke deposition were least pronounced on (Pt–Ce)/ZrO₂ prepared by impregnation of CeO₂ on Pt/ZrO₂ and the catalyst showed highest stability.     

Crosslinked acrylic pressure sensitive adhesives. 3. Effect of adherend on film formation

The reaction of isocyanate in pressure sensitive adhesive (PSA) films adhered on to various adherends having different surface tensions was monitored by depth profiling using attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy.In the latter stages of crosslinking reaction, unreacted isocyanate and its derivatives exist more in the bulk of the PSA than in the interfaces between PSA and adherends which are Teflon sheet and PE film having relatively lower surface tensions. In the case of using stainless steel having relatively higher surface tension as adherend, opposite segregation was observed compared to Teflon and PE.From X-ray photoelectron spectroscopy (XPS), it was revealed that N atoms exist more in surface than in bulk when stainless steel is used as adherend. We conclude that polyisocyanates migrate in the PSA film in order to minimize the magnitude of interfacial free energy between the PSA and the adherend, which leads to the change of surface tension of PSA film.     

Data Center as a Key Player of a District Electric Power and Heat Network System： A Comparison in Urban and Suburb Regions

A DC （data center） demands air-conditioning power as large as the 1/3-1/2 of total electricity consumption. Thus, energy saving of cooling power of DC yields considerable effect on both economic and environmental views. PV （Photovoltaic） and absorption refrigerator with CGS （cogeneration systems） or gas boiler are possible power saving options. The waste warm air from DC would be utilized for greenhouse heating when DC and greenhouse locate near in the suburbs. In this study, the authors develop an energy network model to assess the potential contribution of DC as a major electric power and chilled air consumer as well as the warm air supplier in a district to the energy efficiency improvement. The evaporation heat of LNG （liquefied natural gas） utilization is also considered as well as PV, CGS. This model is applied to the cases of the urban area in Tokyo which involves athletic center, shops and hospital and the suburbs including greenhouse and then compared.     

Adaptive control design for a class of nonsmooth nonlinear systems with matched and linearly parameterized uncertainty

This paper presents an adaptive control design for a class of nonsmooth nonlinear systems with matched uncertainty, which is linearly parameterized with a known discontinuous function. The design framework is based on the concept of the Filippov solution as the classical Lyapunov theory for smooth systems cannot be applied to establish the stability of the adaptive control system due to the presence of the discontinuity. It is proved that as an adaptive control system, the global Lyapunov stability with the convergence of the state of the controlled system to the origin can be achieved by evaluating the monotonicity of the Lyapunov function in the state space, particularly on the discontinuous surface, while the uniqueness of the solution of the closed‐loop system is not necessarily guaranteed. Some interesting numerical examples are demonstrated with simulation results. Copyright © 2008 John Wiley & Sons, Ltd.     

Enhancing integrated earthquake simulation with high performance computing

Integrated earthquake simulation (IES) is a seamless simulation of the three earthquake processes, namely, the earthquake hazard process, the earthquake disaster process and the anti-disaster action process. High performance computing (HPC) is essential if IES, or particularly, the simulation of the earthquake disaster process is applied to an urban area in which 10^4∼6 structures are located. IES is enhanced with parallel computation, and its performance is examined, so that virtual earthquake disaster simulation will be made for a model of an actual city by inputting observed strong ground motion. It is shown that parallel IES has fairly good scalability even when advanced non-linear seismic structure analysis is used.