Highly ordered anodic alumina nanotemplate with about 14 nm diameter

A novel method for the fabrication of highly ordered nanopore arrays with very small diameter of 14 nm was demonstrated by using low-temperature anodization. Two-step anodization was carried out at 25 V, sulfuric acid concentration of 0.3 M, and electrolyte temperature of −15 °C. After anodization, a regular pore array with mean diameter of 14 nm and interpore distance of 65 nm was formed. The pore diameter and regular arrangement were confirmed by scanning electron microscopy (SEM) and fast Fourier transformation (FFT), respectively. The present results strongly suggest that the diameter of pores in a highly ordered alumina template can be reduced by lowering the anodization temperature.     

Collision-Free Interleaver Composed of a Latin Square for Parallel-Architecture Turbo Codes

In parallel-architecture turbo codes, the constituent interleavers must avoid memory collision. This paper proposes a collision-free interleaver structure composed of a Latin square (LS) and pre-designed interleavers. Our proposed interleavers can be easily optimized for various information block sizes and for various degrees of parallelism. Their performances were evaluated by computer simulation.     

Study on the c-axis preferred orientation of ZnO film on various metal electrodes

ZnO thin film was deposited on various metal electrodes by reactive sputtering, and c-axis preferred orientation of the film has been studied. ZnO, which has high piezoelectricity, is promising for oscillators or filter devices such as surface acoustic wave (SAW) device, gas sensor, and film bulk acoustic resonator (FBAR). But, for the application of ZnO film for these devices, the film should be grown with c-axis normal to the electrode. In this study, Pt, Al, and Au were deposited on Si wafer, and the surface roughness and crystal structure of the ZnO film on the electrode were investigated using AFM, scanning electron microscopy (SEM), and X-ray diffraction (XRD). Columnar structures of ZnO films were grown with c-axis normal to all electrodes, and among them Pt electrode showed the highest preferred orientation of ZnO film.     

Preparation of multi-compositional gas sensing films by combinatorial solution deposition

Various compositions of gas sensing films were prepared by the combinatorial deposition of SnO₂, ZnO, and WO₃ sol solutions and their gas sensing behaviors were investigated. The film composition could be manipulated conveniently via the alternate dropping of different oxide sol solutions. From the correlation between film compositions and gas sensitivities, the selective detection of C₂H₅OH and CH₃COCH₃ in the presence of CO, C₃H₈, H₂, and NO₂ could be attained. In addition, the discrimination between C₂H₅OH and CH₃COCH₃, which is a challenging issue due to their similar chemical nature, becomes possible. This research demonstrates the precise design of the sensor-material composition for the selective gas detection via the combinatorial approach.     

公司大门工程建设施工

大门小品建筑属多项目综合性工程。本文作者从管理者的角度 ,通过对公司大门及附属工程施工质量控制的总结 ,说明了质量控制应贯穿于工程施工的全过程     

Existence of Carathe/spl acute/odory solutions in nonlinear systems with discontinuous switching feedback controllers

In this note, we consider the existence of a Carathe/spl acute/odory solution in a single-input-single-output nonlinear system with a discontinuous switching feedback controller. The main contribution is to show that if the nonlinear system can be transformed into a global normal form, then we can specify the value of the discontinuous switching feedback controller on the switching hypersurface so that the closed-loop system has a Carathe/spl acute/odory solution.     

钛精矿回转窑直接还原过程结圈可能性的探讨

通过煤种，入窑球冷态强度和还原过程强度，以及钛精矿与煤灰混合物的软化温度等分析探讨了钛精矿预热球团回转窑直接还原产生结圈的可能性，获得了可以避免结圈的结论。     

The evolving patterns of inter-industrial knowledge structure: Case of Korean manufacturing in the 1980s

The notion of knowledge-based economy premises that technological knowledge be created, accumulated and disseminated through the interactive learning among principal actors in the national system. This paper analyzes, from a dynamic perspective, the structure of inter-industrial technological knowledge. Both human-driven disembodied channel and capital-driven embodied channel are investigated based on network analysis. The set of empirical data covers the Korean manufacturing sector during the 1980s. Overall, density of network tends to be increasing over time, implying that knowledge network becomes expanded and intensified. A number of distinctive features are identified between knowledge types and industrial categories. The findings in turn render important policy implications that should be addressed when developing technology policy. Clearly, the policy framework needs to be industry-specific and country-specific in accordance with the development stage and industrial structure of reference time. This revised version was published online in August 2006 with corrections to the Cover Date.     

KMLS型立式砂泵的振动噪声产生原因及解决措施

针对KMLS型立式砂泵振动、噪声产生原因及其表现特征,提出了解决措施。通过对这些原因的分析研究,可以提供泵设计者和生产者在减少砂泵振动方面采取相应的措施,使KMLS型立式砂泵能更好的服务于用户。     

Construction Robot Path-Planning for Earthwork Operations

In developing an intelligent mobile construction robot, a navigation system that can provide an effective and efficient path-planning algorithm is a very important element. The purpose of a path-planning method for a mobile construction robot is to find a continuous collision-free path from the initial position of the construction robot to its target position. This paper presents an improved Bug-based algorithm, called SensBug, which can produce an effective path in an unknown environment with both stationary and movable obstacles. The contributions, which make it possible to generate an effective and short path, are an improved method to select local directions, a reverse mode, and a simple leaving condition. Some emerging technologies that can be used for implementing an intelligent construction robot are introduced in this paper.