Preparation of bismuth nanowire encased in quartz template for Hall measurements using focused ion beam processing

ABSTRACT: Forming electrodes on opposite sides of an individual bismuth nanowire was attempted to prepare for Hall measurements. Although a 1-mm-long bismuth nanowire which is completely covered with a quartz template has been successfully fabricated to prevent oxidation, it is very difficult to attach Hall electrodes on the opposite sides of the nanowire due to the quartz covering. One side of the cylindrical quartz template was removed by polishing without exposure of the nanowire to the atmosphere; the thickness between the polished template surface and the nanowire was estimated to be several micrometers. Focused ion beam processing was successfully employed to expose both surfaces of the nanowire under high vacuum by removing part of the quartz template. A carbon thin film was then deposited in situ on the wire surface to fabricate an electrical contact on the bismuth nanowire sample. Furthermore, the energy dispersive X-ray analysis was performed to the area processed by focused ion beam, and the bismuth component of the nanowire was successfully detected. It was confirmed that the focused ion beam processing was applicable to attach electrodes to bismuth nanowire for Hall measurement.     

Indentation-induced ductile behavior of glass–ceramics involving layered aluminosilicates

Contact damage in materials is critical in engineering applications because it influences mechanical resistance, such as wear, erosion, and impact failure. Indentation tests were performed using a tungsten carbide ball indenter (Hertzian contact) on the surfaces of glass–ceramics containing hexagonal CaAl₂Si₂O₈ or mica crystals (fluorophlogopite), both of which have a layered structure. The stress–strain relation and the permanent deformation on the surface, as well as the observation of the microcrack zone by X-ray computed tomography using synchrotron radiation, revealed that the glass–ceramic with hexagonal CaAl₂Si₂O₈ showed ductility similar to the quasi-plastic behavior previously observed in the mica glass–ceramic. The yield stresses of the glass–ceramics were estimated from the stress deviating from the stress–strain relation assuming complete elastic response between the ball and the sample. The ratio of the yield stress to Young modulus (Y/E) of the glass–ceramic with hexagonal CaAl₂Si₂O₈ was determined to be higher than that of the mica glass–ceramic.     

Granulation of a hardmetal powder for spark plasma sintering

A fluidized bed granulation method, pressure swing granulation (PSG), was applied to granulation of a hardmetal powder without pressing lubricants for making the upstream process of spark plasma sintering (SPS) more efficient.

The properties of the granules were examined and compared with those of spray dried granules and extruded ones under the present system using a sieve.

Spherical granules between 0.15 and 0.84 mm in diameter difficult to obtain by the spray drying were obtained with high yield. The flowability of the granules was far better than that of spray dried granules and similar to that of extruded ones. Iron contamination and oxidization during pressure swing granulation were tolerable to the real production.     

Thermal strain of high strength polyethylene fiber in low temperature

High strength polyethylene fiber (Toyobo, Dyneema® fiber: hereinafter abbreviated to DF) has a negative thermal expansion coefficient. Relation between fiber structure and thermal strain of DF used as reinforcement of DF reinforced plastic (DFRP) for cryogenic use was investigated. The crystallinities and orientation angles of several kinds of polyethylene fibers having different modulus from 15 to 134Gpa (herein after abbreviated to DFs) were measured by NMR and X‐ray. We obtained the parameters of the mechanical series‐parallel model composed of crystal and amorphous by crystallinity and modulus. Thermal expansion coefficients of DFs were estimated by mechanical series‐parallel model. All DFs having different modulus showed negative thermal expansion coefficients in the temperature range from 180 to 300K, and absolute values of those markedly increased by increasing tensile modulus of DF. The estimated thermal expansion coefficients showed negative values, and thermal strains showed a similar curve to observed ones mostly. Average thermal expansion coefficients in the temperature range from 180 to 300K estimated by mechanical model agreed with the observed ones. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2918–2925, 2004     

Control of Oxidation State of Eu Ions in Na2O–Al2O3–SiO2 Glasses

Glasses doped with well‐controlled Eu³⁺ and Eu²⁺ ions have attracted considerable interest due to the possibility of tuning the wavelength range of the emitted light from violet to red by using their ⁵D₀→⁷F_j and 5d–4f electron transitions. Glasses were prepared to dope Eu³⁺ ions in a Na₂O–Al₂O₃–SiO₂ system, and the changes in the valence state of Eu³⁺ ions and the glass structure surrounding the Eu atoms during heating under H₂ atmosphere were investigated using fluorescence spectroscopy, X‐ray absorption fine‐structure spectroscopy, and ²⁷Al magic‐angle spinning solid‐state nuclear magnetic resonance spectroscopy. The reduction behavior of Eu³⁺ ions was dependent on the Al/Na molar ratio of the glass. For Al/Na < 1, the Al³⁺ ions formed the AlO₄ network structure accompanied by the Na⁺ ions as charge compensators; the Eu³⁺ ions occupied the interstitial positions in the SiO₄ network structure and were not reduced even under heating in H₂ gas. On the other hand, in the glasses containing Al₂O₃ with the Al/Na ratio exceeding unity, the Eu³⁺ ions commenced to be coordinated by the AlO₄ units in addition to the SiO₄ network structure. When heated in H₂ gas, H₂ gas molecules reacted with the AlO₄ units surrounding Eu³⁺ ions to form AlO₆ units terminated with OH bonds, and reduced Eu³⁺ ions to Eu²⁺ via the extracted electrons.     

Efficacy of Chemical Mimicry by Aphid Predators Depends on Aphid-Learning by Ants

Chemical mimicry is an effective strategy when signal receivers recognize and discriminate models by relying on chemical cues. Some aphid enemies mimic the cuticular chemicals of aphids through various means thus avoiding detection and attack by aphid-tending ants. However, because ants have been reported to learn the chemical signatures of aphids in order to distinguish the aphids, the efficacy of chemical mimicry is predicted to depend on the experience of the ants that had tended aphids. The present study tested this hypothesis using two predator species: larvae of the green lacewing Mallada desjardinsi, and larvae of the ladybeetle Scymnus posticalis. Lacewing larvae carry the carcasses of aphids on which they have preyed upon their backs, and these function via chemical camouflage to reduce the aggressiveness of aphid-tending ants toward the larvae. Ladybeetle larvae reportedly produce a covering of wax structures, and their chemicals appear to attenuate ant aggression. We examined whether the behavior of the ant Tetramorium tsushimae toward these predators changed depending on their aphid-tending experience. Ants moderated their aggressiveness toward both predators when they had previously tended aphids, indicating that chemical mimicry by both aphid predators is dependent on previous experience of the ants in tending aphids. Chemical mimicry by the predators of ant-tended aphids is therefore considered to exploit learning-dependent aphid recognition systems of ants.     

In Situ Synthesis and Microstructures of Tungsten Carbide-Nanoparticle-Reinforced Silicon Nitride-Matrix Composites

A W₂C-nanoparticle-reinforced Si₃N₄-matrix composite was fabricated by sintering porous Si₃N₄ that had been infiltrated with a tungsten solution. During the sintering procedure, nanometer-sized W₂C particles grew in situ from the reaction between the tungsten and carbon sources considered to originate mainly from residual binder. The W₂C particles resided in the grain-boundary junctions of the Si₃N₄, had an average diameter of ∼60 nm, and were polyhedral in shape. Because the residual carbon, which normally would obstruct sintering, reacted with the tungsten to form W₂C particles in the composite, the sinterability of the Si₃N₄ was improved, and a W₂C–Si₃N₄ composite with almost full density was obtained. The flexural strength of the W₂C–Si₃N₄ composite was 1212 MPa, ∼34% higher than that of standard sintered Si₃N₄.     

Effect of Phosphorus Ions on the Proton Conductivity in the Sol–Gel-Derived Porous Glasses

The effect of phosphorus ions on the proton conductivity was examined for the sol–gel-derived glasses. The porous glasses were prepared through hydrolysis of PO(OCH₃)₃ and Si(OC₂H₅)₄, in which the phosphorus ions consisted of the POH bonds and were dissolved into the silica matrix without any P-O-Si bond. The electrical conductivity increased in a humid atmosphere and reached ∼30 mS/cm at 50°C under 70% RH. High conductivity is achieved by both the POH bonds and the molecular water bonded to the POH bonds. The conductivity increased with a change in humidity from 40% to 80% RH. The phosphorus ions were selectively dissolved in water, resulting in a lower conductivity.     

Flow instability in capillary extrusion of plasticized poly(vinyl chloride)

Flow instability in a capillary extrusion is studied for a high molecular weight, plasticized poly(vinyl chloride) (PVC). The onset of melt fracture correlates with the long time relaxation ascribed to the generation and/or growth of PVC crystallites. An increase in the residence time in the cylinder leads to this long time relaxation and results in the melt fracture, although the apparent shear stress remains constant, irrespective of the residence time. The extrudate temperature and the species of the plasticizer also have a significant influence on the apparatus of the extruded products. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1277–1283, 2001