Enhancement of melt elasticity for poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) by addition of weak gel

Rheological properties in a molten state are studied extensively for poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate), PHB‐HV, with a small amount of crosslinked poly(epichlorohydrin), PECH, having low density of crosslink points. It is found that adding 2 wt % of xPECH greatly enhances the melt elasticity of PHB‐HV, one of the serious defects of microbial PHB, whereas it has no effect on the shear viscosity. As a result, viscoelastic nature, and thus processability, of PHB‐HV can be controlled by blending the crosslinked PECH. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Hot Isostatic Pressing of Reactive SnO2 Powder

Tin(IV) oxide (SnO₂) crystallizes at room temperature by adding hydrazine monohydrate ((NH₂)₂· H₂O) to a hydrochloric acid solution of tin, followed by washing and drying. Well-densified SnO₂ ceramics (99.8% of theoretical) with an average grain size of 0.9 μm have been fabricated by hot isostatic pressing for 2 h at 900°C and 196 MPa. Their Vickers hardness and bending strength are 14.4 GPa and 200 MPa, respectively. They exhibit an electrical conductivity of 2 × 10⁻³−9 × 10⁻³ S·cm⁻¹ at room temperature.     

Optical and acoustical investigation for plastic deformation of isotactic polypropylene/ethylene-1-hexene copolymer blends

The effects of morphology on mechanism of plastic deformation are investigated for binary blends of isotactic polypropylene and rubbery ethylene-1-hexene copolymers. In this work, plastic deformation developed during elongation is investigated by measuring light transmittance, electron microscopy, and ultrasonic propagation in the temperature region between 298 K and 353 K. It is found that the compatible blends hardly show stress-whitening at any temperature, whereas the incompatible blends show distinct stress-whitening below 333 K. Furthermore, microscopic defects such as microvoids and crystalline defects are found to be precursors for crazing which are origin of the stress-whitening.     

The effects of air pollution and climatic factors on atmospheric corrosion of marble under field exposure

The atmospheric corrosion of marble was evaluated in terms of SO₂ concentration as air pollution and climatic factors such as rainfall, relative humidity, temperature and so on under the field exposure. Marble of calcite type (CaCO₃) was exposed to outdoor atmospheric environment with and without a rain shelter at four test sites in the southern part of Vietnam for 3-month, 1- and 2-year periods from July 2001 to September 2003. The thickness loss of marble was investigated gravimetrically. X-ray diffraction and X-ray fluorescent methods were applied to study corrosion products on marble. The corrosion product of marble was only gypsum (CaSO₄ · 2H₂O) and was washed out by rain under the unsheltered exposure condition. It was found that the most substantial factors influencing the corrosion of marble were rainfall, SO₂ concentration in the air and relative humidity. Based on the results obtained, we estimated the dose-response functions for the atmospheric corrosion of marble in the southern part of Vietnam.     

Reaction joining of SiC ceramics using TiB2-based composites

SiC ceramics were reaction joined in the temperature range of 1450–1800 °C using TiB₂-based composites starting from four types of joining materials, namely Ti–BN, Ti–B₄C, Ti–BN–Al and Ti–B₄C–Si. XRD analysis and microstructure examination were carried out on SiC joints. It is found that the former two joining materials do not yield good bond for SiC ceramics at temperatures up to 1600 °C. However, Ti–BN–Al system results in the connection of SiC substrates at 1450 °C by the formation of TiB₂–AlN composite. Furthermore, nearly dense SiC joints with crack-free interface have been produced from Ti–BN–Al and Ti–B₄C–Si systems at 1800 °C, i.e. joints TBNA80 and TBCS80, whose average bending strengths are measured to be 65 MPa and 142 MPa, respectively. The joining mechanisms involved are also discussed.     

Size-dependent correction factors for absorption measurements using filter-based photometers: PSAP and COSMOS

Filter-based absorption photometers have been widely used to measure mass concentrations of black carbon (BC) by measurement of the absorption coefficient of BC. In these techniques, correction for the effect of multiple scattering by the filter medium is necessary, even if only BC particles are extracted by evaporating co-existing volatile compounds using a heated inlet. The correction depends on particle size, because it varies with the aerosol penetration depth into the filter. The size dependence has not, however, been taken into account in previous studies. For the first time, we quantify the particle size dependence of the sensitivities of two filter-based photometers, PSAP and COSMOS, using mono-disperse nigrosin particles, which were generated by the combination of a differential mobility analyzer and an aerosol particle mass analyzer. At diameters smaller than 200 nm, the absorption coefficients measured by PSAP and COSMOS were much larger than those calculated by Mie theory. The size-dependent correction factors for PSAP and COSMOS are determined by comparing the observed absorption coefficients at a flow rate of 0.7 standard liter per minute with those calculated by Mie theory. The correction factors to the mass absorption cross-section are also estimated for typical size distributions of ambient black carbon particles. The new factors reduce the mass absorption cross-sections measured by PSAP and COSMOS by 28–36% for typical ambient black carbon particles observed with an inlet heated to 400 °C.     

Effect of thermal annealing on electrical degradation characteristics of Sb–Bi–Mn–Co-added ZnO varistors

The effects of thermally annealing Bi–Mn–Co–Sb₂O₃-added ZnO varistors on their electrical degradation were investigated. For the samples added with 0.01 mol% Sb₂O₃ and without Sb₂O₃, no marked difference in the nonlinearity index α of the voltage–current (V–I) characteristics was observed upon electrical degradation for the annealed and nonannealed samples. Upon increasing the amount of Sb₂O₃ added, the values of α increased after electrical degradation for the annealed samples. Moreover, the value of α after electrical degradation was proportional to the width of gauss function (width) of the X-ray diffraction peak for Zn_2.33Sb_0.67O₄-type spinel particles under various annealing conditions. The added Sb₂O₃ did not dissolve in the ZnO grains but became segregated at grain boundaries. Therefore, it is speculated that the increase in the width of the spinel particles is due to the increase in the numbers of fine spinel particles at grain boundaries and triple points. Furthermore, it is suggested that the improvement of the electrical degradation is due to the decrease in the mobility of oxide ions or Zn²⁺ ions owing to their being blocked by uniformly dispersed fine spinel particles at grain boundaries.     

Effect of heating process on the formation of nanoparticles of elastin model polypeptide, (GVGVP)251, by gamma-ray crosslinking

Nanoparticles were prepared by the thermosensitive aggregation of the elastin model polypeptide, (GVGVP)₂₅₁, and gamma-ray crosslinking. Three different heating processes, “slow heating,” “fast heating,” and “heat shock,” were used for the aggregation of the peptide, followed by gamma-ray crosslinking. Only the “heat shock” process successfully yielded stable nanoparticles with diameters of less than ca. 150 nm and a narrow size distribution. Circular dichroism (CD) spectrometry showed that this polypeptide formed a type-II β-turn structure when the temperature was increased to above the cloudy point in the case of the “heat shock” process; suggesting that this structure might contribute to stable nanoparticle formation by gamma-rays. CD spectrometry also suggested that this structure would be affected during the formation of stable crosslinked particles.     

Mechanochemically synthesized ZIF-8 nanoparticles blended into 6FDA-TrMPD membranes for C3H6/C3H8 separation

The mixed matrix membranes (MMMs) consisting zeolitic-imidazolate framework-8 (ZIF-8) nanoparticles in a polymer have been of considerable interest in separation applications. The fillers used are mostly synthesized using the solvothermal method. In this study, the ZIF-8 nanoparticles were synthesized using a solvent-less and salt-free mechanochemical method and were added to 6FDA-TrMPD polyimide to prepare MMMs. The single gas permeation of C₃H₆ and C₃H₈ through the MMMs was investigated. The C₃H₆ permeability and C₃H₆/C₃H₈ ideal selectivity of a 20 wt% mechano-synthesized ZIF-8/6FDA-TrMPD MMM were 70% and 32% higher than those of the neat polymer membrane at 0.1 MPa and 308 K, respectively. The C₃H₆/C₃H₈ separation performance of the mechano-synthesized ZIF-8 MMM was similar to that of the conventional solvothermal-synthesized ZIF-8 MMM. This separation performance was in good agreement with the Maxwell model. Temperature and pressure dependence analyses confirmed that the mechano-synthesized ZIF-8 nanoparticles acted as molecular sieves in the MMMs for the C₃H₆ and C₃H₈ permeation.     

Effect of molecular weight on molecular orientation and morphology of polypropylene sheets containing a β-nucleating agent

In this study, polypropylene (PP) films containing the β nucleating agent, N,N′-dicyclohexyl-2,6-naphthalenedicarboxamide, were prepared using PP with three different molecular weights (low, medium, and high) by extrusion process with T-shaped die. The structure and morphology of the films were studied after stretching. It was found that a unique molecular orientation, in which both the c-axis and crystalline lamellae were oriented perpendicular to the flow direction, was formed in all undrawn film samples, irrespective of the molecular weights of the PP. In the PP sheets stretched in the machine direction, the low-molecular-weight sample containing the nucleating agent exhibited brittle properties owing to a lack of tie chains in the stretching direction. In contrast, cavitation was prominent in the medium (M-PP)- and high (H-PP)-molecular-weight samples. Notably, M-PP containing the nucleating agent, with a high degree of molecular orientation, promoted the formation of a large number of voids. In H-PP containing the nucleating agent, the presence of numerous tie chains inhibited cavitation, resulting in fewer voids. The experimental results demonstrated the influence of the molecular weight on the void structure, which will be useful in the field of microporous membranes.