Yttrium oxide based metal-insulator-semiconductor structures on silicon

Yttrium oxide based metal-insulator-semiconductor (MIS) structures on silicon have been studied. Yttrium films of thickness of nearly 200 Å were deposited by electron beam evaporation on silicon substrates held at room temperature. The oxidation of yttrium was performed at 750 °C for 1 h in dry oxygen. Scanning electron microscopy showed a smooth surface morphology for oxidized films. X-ray diffraction analyses were also performed, but did not confirm the crystalline nature of the oxide. Capacitance-voltage and current-voltage measurements were conducted to characterize aluminum-yttrium oxide-silicon MIS structures. The results have demonstrated the potential of using yttrium oxide as a gate dielectric.     

Bacteriophages of enteric bacteria in drinking water, comparison of their distribution in two countries

The presence of bacteriophages infecting enteric bacteria was tested in more than 1500 drinking water samples in Israel and Spain. Bacteriophages tested were somatic coliphages, F-specific bacteriophages and Bacteroides fragilis bacteriophages. The three groups of bacteriophage were isolated in 100 ml water samples by the presence/absence test with similar frequencies, which ranged from 4.4% for somatic coliphages to 6.1% for bacteriophages infecting Bact. fragilis. In contrast, the frequency of isolation of bacteriophages was significantly higher than the frequency of isolation of faecal coliforms, which averaged only 1.9%. No significant differences were observed between the frequencies of isolation between the samples tested in Spain and those tested in Israel. The percentage of groundwater samples containing faecal coliforms and somatic coliphages was reduced significantly by chlorination, despite known deficiencies. However, there was no effect on the occurrence of F-specific bacteriophages and Bact. fragilis bacteriophages.     

Using computational fluid dynamics to improve the drag coefficient estimates for tall buildings under wind loading

Wind is the main horizontal force acting on tall buildings. This force is proportional to the drag coefficient. The drag coefficient is an important factor in their structural design. Designers have historically relied upon experimental wind tunnel results to estimate the drag coefficient. However, this process is both expensive and time consuming. In this study, we alternatively computed the drag coefficient (apart from the pressure, force, and bending moment) using computational fluid dynamics for a typical 93‐m‐high residential building. The simulation considers the actual building geometry, as well as the neighborhood roughness effects. We compared these results with the conventional estimates contained in the Brazilian code NBR‐6123/1988 and Eurocode EC1. The results indicated that the pressures obtained herein near the top of the building were lower compared to those obtained using conventional estimation methods given in codes. Comparatively, the obtained bending moment relative to the base of the building was higher, indicating the existence of significant drag forces not considered in codes. In fluid dynamics simulations, the drag coefficient is determined for each terrain condition. Computational fluid dynamics can effectively simulate the drag force and resultant forces in the direction of the flow, as well as the vortices that result during coating detachment and other types of damage.     

Time- and temperature-dependence of compressive and tensile behaviors of polypropylene fiber-reinforced cemented paste backfill

The understanding of compressive and tensile behaviors of polypropylene fiber-reinforced cemented paste backfill (FR-CPB) play crucial roles in the successful implementation of reinforcement technique in underground mine backfilling operations. However, very limited studies have been performed to gain insight into the evolution of compressive and tensile behaviors and associated mechanical properties of FR-CPB under various curing temperatures from early to advanced ages. Thus, this study aims to investigate the time (7, 28, and 90 d)- and temperature (20°C, 35°C, and 45°C)-dependence of constitutive behavior and mechanical properties of FR-CPB. The obtained results show that pre- and post-failure behaviors of FR-CPB demonstrate strongly curing temperature-dependence from early to advanced ages. Moreover, the pseudo-hardening behavior is sensitive to curing temperature, especially at early ages. Furthermore, the mechanical properties including elastic modulus, material stiffness, strengths, brittleness, cohesion, and internal friction angle of FR-CPB show increasing trends with curing temperature as curing time elapses. Additionally, a predictive model is developed to capture the strong correlation between compressive and tensile strength of FR-CPB. The findings of this study will contribute to the successful implementation of FR-CPB technology.     

Discrimination of n-3 Rich Oils by Gas Chromatography

Exploring the capabilities of instrumental techniques for discriminating n-3 rich oils derived from animals is a very important though much neglected area that was emphasized more than 100 years ago. In this study the potential of gas chromatography (GC) for discriminating full fatty acid methyl ester (FAME) profiles from fish (cod liver and salmon) and marine mammal (seal and whale) oils is evaluated by means of principal component analysis (PCA). The FAME profiles from plant oils such as rapeseed, linseed and soy oils and seven different brands of n-3 supplements are also used in the discrimination process. The results from the PCA plots can reliably distinguish between plant, n-3 supplements, fish and marine mammal oils. By removing the contribution of the n-3 supplements and plant oils it is possible to discriminate between types of fish and marine animal oils. GC offers a rapid, simple and convenient means of discriminating oils from different species, brands and grades.     

Corrosion aspects of alkyd paints modified with linseed and soy oils

The anticorrosive performance of medium-long (54-59%) alkyd paints modified with linseed and soy oils was compared by accelerated tests (Prohesion Cycle) and natural exposition in marine and industrial atmospheres. Differences on the protection mechanism of anticorrosive pigments due to substitution of linseed oil by soy oil were investigated by polarization curves and electrochemical impedance spectroscopy (EIS). Complementary tests such as water vapor and ions permeability in freestanding films were also performed. Results suggested that the type of oil influenced the barrier properties of the paint pigmented with zinc phosphate. The same tendency was verified by resistance values obtained from impedance diagrams. Polarization curves suggest that the action of the pigments in the alkyd paintings is practically the same for both oils. The substitution of linseed oil by soy oil did not impair the anticorrosive performance of alkyd paints and from the economic point of view this substitution could be very interesting.     

Reliability and validity of self-reported burnout in college students: A cross randomized comparison of paper-and-pencil vs. online administration

Internet data collection is becoming increasingly popular in all research fields dealing with human perceptions, behaviors and opinions. Advantages of internet data collection, when compared to the traditional paper-and-pencil format, include reduced costs, automatic database creation, and the absence of researcher-related bias effects, such as availability and complete anonymity. However, the validity and reliability of internet gathered data must be established, in comparison to the usual paper-and-pencil accepted formats, before an inferential analysis can be done. In this study, we compared questionnaire data gathered from the internet with that from the traditional paper-and-pencil in a sample of college students. The questionnaires used were the Maslach Burnout Inventory - Student Survey (MBI-SS), the Oldenburg Burnout Inventory (OBI-SS) and the Copenhagen Burnout Inventory (CBI-SS). Data was gathered through a within-subject cross randomized and counterbalanced design, on both internet and paper-and-pencil formats. The results showed no interference in the application order, and a good reliability for both formats. However, concordance between answers was generally higher in the paper-and-pencil format than on the internet. The factorial structure was invariant in the three burnout inventories. Data gathered in this study supports the Internet as a convenient, user-friendly, comfortable and secure data gathering method which does not affect the accepted factorial structures existent in the paper format of the three burnout inventories used.     

Introducing concurrency in sequential Java via laws

Nowadays multi-core processors can be found everywhere. It is well known that one way of improving performance is by parallelization. In this paper we propose a parallelization strategy for Java using algebraic laws. We perform an experiment with two benchmarks and show that our strategy produces a gain similar to a specialized parallel version provided by the Java Grande Benchmark (JGB).