When reaction-bonded silicon nitride containing MgO/Y2O3 additives is sintered at three different temperatures to form sintered reaction-bonded silicon nitride (SRBSN), the thermal conductivity increases with sintering temperature. The β-Si3N4 (silicon nitride) crystals of SRBSN ceramics were synthesized and characterized to investigate the relation between the crystal structure and the lattice oxygen content. The hot-gas extraction measurement result and the crystal structure obtained using Rietveld analysis suggested that the unit cell size of the β-Si3N4 crystal increases with the decrease in the lattice oxygen content. This result is reasonable considering that the lattice oxygen with the smaller covalent radius substitutes nitrogen with the larger one in the β-Si3N4 crystals. The lattice oxygen content decreased with increasing sintering temperature which also correlated with increase in thermal conductivity. Moreover, it is noteworthy from the viewpoint that it may be possible to apply the lattice constant analysis for the nondestructive and simple measurement of the lattice oxygen content that deteriorates the thermal conductivity of the β-Si3N4 ceramics. 相似文献
In quenching, the cooling uniformity is most important to diminish distortion occurring on work pieces. As a trial to accomplish uniform cooling, therefore, there exist various mixing methods of a quenchant and the quenchant circulation with an external pump has so far been the well accepted mixing method. However, this study proposes an advanced oscillation mixing method that can improve more the cooling uniformity in quenching. The proposed method includes a stirrer in oscillating motion, so that the simultaneous oscillating and mixing movements of the stirrer are considered to provide efecfively the uniform cooling characteristics for the quenchant. In comparison with the case of the circulation pump mixing, the investigation using the oscillation mixing method has demonstrated the following two experimental facts:(1) the short vapor blanket stage caused by the quick breakage of the oil vapor blanket and (2) the reduced variation of the quenching distortion. 相似文献
The microstructure development during plastic deformation was reviewed for iron and steel which were subjected to cold rolling
or mechanical milling (MM) treatment, and the change in strengthening mechanism caused by the severe plastic deformation (SPD)
was also discussed in terms of ultra grain refinement behavior. The microstructure of cold-rolled iron is characterized by
a typical dislocation cell structure, where the strength can be explained by dislocation strengthening. It was confirmed that
the increase in dislocation density by cold working is limited at 1016m−2, which means the maximum hardness obtained by dislocation strengthening is HV3.7 GPa. However, the iron is abnormally work-hardened
over the maximum dislocation strengthening by SPD of MM because of the ultra grain refinement caused by the SPD. In addition,
impurity of carbon plays an important role in such grain refinement: the carbon addition leads to the formation of nano-crystallized
structure in iron. 相似文献
Epitaxial multilayer thin films of infinite-layer (Sr, Ca)CuO2 and perovskite (Sr, Ca)RuO3 have been prepared on (100) SrTiO3 substrates by multitarget rf magnetron sputtering. X-ray diffraction analyses revealed that the multilayer structure of (Sr, Ca)CuO3/(Sr, Ca)RuO3 was successfully fabricated with a minimum layer thickness of 20 Å. Transmission electron microscopy measurements of the multilayers indicated that there was no dislocation which normally exists in single-layer films with an infinite-layer structure. Resistivities of multilayer films at room temperature ranged from 1 to 10 m cm and showed semiconductor-like dependence against the temperature. 相似文献
Epilepsy is a neurological disorder that may affect the autonomic nervous system (ANS) from 15 to 20 min before seizure onset, and disturbances of ANS affect R–R intervals (RRI) on an electrocardiogram (ECG). This study aims to develop a machine learning algorithm for predicting focal epileptic seizures by monitoring R–R interval (RRI) data in real time. The developed algorithm adopts a self-attentive autoencoder (SA-AE), which is a neural network for time-series data.
The results of applying the developed seizure prediction algorithm to clinical data demonstrated that it functioned well in most patients; however, false positives (FPs) occurred in specific participants. In a future work, we will investigate the causes of FPs and optimize the developing seizure prediction algorithm to further improve performance using newly added clinical data.
To minimize the deviation of the predicted creep curves obtained under constant load conditions by the original θ projection model, a new modified version that can be expressed by , was derived and experimentally validated in our last study. In the present study, the predictive capability of the modified θ projection model was investigated by comparing the simulated and experimentally determined creep curves of K465 and DZ125 superalloys over a range of temperatures and stresses. Furthermore, the linear relationship between creep temperature and initial stress was extended to the 5-parameter model. The results indicated that the modified model could be used as a creep life prediction method, as it described the creep curve shape and resulted in predictions that fall within a specified error interval. Meanwhile, this modified model provides a more accurate way of describing creep curves under constant load conditions. The limitations and future direction of the modified model were also discussed. In addition, this modified θ projection model shows great potential for the evaluation and assessment of the service safety of structural materials used in components governed by creep deformation. 相似文献
To avert potential crisis from Japan’s aging infrastructure and declining birth rate, the Japanese Government is planning to introduce robotic technology for the inspection of social infrastructure (such as pipes, dams, and bridges). Recording underwater positions is a difficult task for human divers who undertake conventional dam inspections. This study presents the Anchor Diver 5.2 system for efficient and effectual dam inspection. Anchor Diver 5.2 is based on an extended-tether-maneuvered remotely operated vehicle (ROV) equipped with cameras. The ROV is lowered into water by a hoist system from a boat and implements a visual survey of the concrete underwater structure. To improve the visibility of the ROV in murky and cloudy water, a novel concept named Water Loupe is proposed. In addition, a simple boat-fixing method is proposed to provide a stable base on the water surface, and the underwater position of the ROV, which cannot be accessed by global positioning systems, is recorded using a feasible localization method. Finally, the developed system was evaluated in field experiments conducted in the Amagase Dam, Japan, and its merits and problems are discussed. 相似文献