Porous poly(L‐lactic acid)/poly(ethylene glycol) blend films

Poly(L ‐lactic acid) (PLLA: M_w = 19.4 × 10⁴)/poly(ethylene glycol) (PEG: M_w = 400) blend films were formed by use of a solvent‐cast technique. The properties and structures of these blend films were investigated. The Young's modulus of the PLLA decreased from 1220 to 417 MPa with the addition of PEG 5 wt %, but the elongation at break increased from 19 to 126%. The melting point of PLLA linearly decreased with increases in the PEG content (i.e., pure PLLA: 172.5°C, PLLA/PEG = 60/40 wt %: 159.6°C). The PEG 20 wt % blend film had a porous structure. The pore diameter was 3–5 μm. The alkali hydrolysis rate of this blend film was accelerated due to its porous structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 965–970, 2004     

Advantage of Sodium Polyoxyethylene Lauryl Ether Carboxylate as a Mild Cleansing Agent

Five anionic surfactants widely used in commercial skin cleansers were studied: sodium polyoxyethylene lauryl ether carboxylate (EC), sodium polyoxyethylene alkyl ether sulfate (ES), sodium dodecyl sulfate, potassium laurate, and N-cocoyl-l-glutamic acid monosodium salt. The amount of surfactant from aqueous solution adsorbed into the stratum corneum (SC), the degree of SC swelling, the change of the secondary structure of SC proteins (denaturation). The surface tension of surfactant–zein mixed solutions, and the solubilization behavior of zein were measured. Results showed that EC had the lowest adsorption into SC, the lowest SC swelling, and lowest denaturation of SC proteins. Low interactions between surfactants and SC proteins were also observed for EC/ES mixture solutions as well as. Mixing EC with ES good foaming performance. The EC/ES mixture, at about 1:1 ratio, is an excellent surfactant system for skin cleanser applications having cleansing characteristics and mildness to the skin.     

Increasing the hydrophobic interaction between terminal W-motifs enhances the stability of Salmonella typhimurium sialidase. A general strategy for the stabilization of {beta}-propeller protein fold

Protein engineering of the ß-propeller protein aimedat enhancing the structural stability of the protein was carriedout using a monomeric single domain ß-propeller protein,Salmonella typhimurium sialidase, as a model. Ala53 and Ala69each located at strands B and C of the W1 motif were mutatedto Leu and Val, respectively, to increase the hydrophobic interactionbetween W1 and W6 motifs. The mutants showed enhanced stabilitytowards guanidine hydrochloride and thermal unfolding. Ala53Leushowed higher stability, probably owing to the capability ofthe mutated Leu to interact extensively with more residues involvedin the hydrophobic interactions between the terminal W-motifs.The mutations, which are located far from the active site, haveno significant effect on the enzymatic properties. The strategyto enhance the stability proposed here might be applied to theother ß-propeller proteins.     

Entrap-immobilization of invertase on composite gel fiber of cellulose acetate and zirconium alkoxide by sol–gel process

We prepared a composite gel fiber by the gel formation of cellulose acetate and zirconium tetra-n-butoxide. Gel fiber is stable in common solvents, phosphate solution, and electrolyte solution. Invertase was entrap-immobilized on the gel fiber. The immobilization was easily performed under the mild conditions. The apparent Michaelis constant (K_m) and maximum reaction velocity (V_max) were estimated from Eadie–Hofstee plot for immobilized invertase. The K_m of immobilized invertase was larger than that of native invertase, while the opposite tendency was observed for the V_max. The activity for the immobilized invertase became higher with increasing fiber diameter. It indicates that the hydrolysis of sucrose occurs in the neighborhood of the fiber surface. The thermal stability of the immobilized invertase was higher than those of its native counterpart. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2084–2088, 2001     

EFFECTS OF OPERATIONAL CONDITIONS ON DRYING CHARACTERISTICS IN CLOSED SUPERHEATED STEAM DRYING

The effects of operational conditions on the drying performance in closed superheated steam drying were examined theoretically and experimentally. The vapor generated from the sample was circulated in the drying chamber. In the theoretical analysis, the replacement of air with vapor in drying chamber and the convective vapor transfer in sample were considered. At the start of drying, the drying chamber was filled with air. As the drying proceeded, the air was replaced with the vapor generated from sample. The calculated results explained the characteristics of experimental data. The pore diameter of sample had little effect on the drying characteristics. During the internal evaporation period, the evaporation occurred in the narrow zone, which moved from the surface to the bottom of sample. The convective vapor transfer in sample had a significant influence on the drying performance. The excess increments in temperature and velocity of drying gas hardly contributed to shortening the drying time.     

Phase Relations and Volume Changes of Hafnia under High Pressure and High Temperature

Using multi-anvil high-pressure devices and synchrotron radiation, X-ray in situ observations of HfO₂ under high pressure and high temperature have been performed to investigate its phase relations and compression behavior. An orthorhombic phase (orthoI) is stable from 4 to 14.5 GPa below 1250°–1400°C and transforms to a tetragonal phase, which is one of the high-temperature forms of HfO₂, above these temperatures. Another orthorhombic phase (orthoII) with a cotunnite-type structure appears above 14.5 GPa. OrthoII is stable up to 1800°C at 21 GPa. OrthoII is quenchable to ambient conditions. The orthoI-to-orthoII transition is accompanied by ∼8 vol% decrease. The bulk moduli of orthoI and orthoII at room temperature are 220 and 312 GPa, respectively. This low compressibility of orthoII indicates that it is a potential candidate for very hard materials.     

Dehydrogenative polycondensation of telechelically bis(dimethylsilyl)functionalized oligo(dimethylsiloxane)s or aromatics and 1,3,3,5,5,7,7,7-octamethyltetrasiloxane

Telechelically bis(hydrodimethylsilyl)-functionalized oligo(dimethylsiloxane)s or aromatics were found to give polymers constituting of alternating disilylene and oligodimethylsiloxane or 4,4′-diylaromatics as repeating units by dehydrogenative coupling reaction in the presence of palladium dibenzylideneacetone complex. The same catalyst gave polysilylenes with trisiloxane pendant from 1,1-dihydro-1,3,3,5,5,7,7,7-octamethyltetrasiloxane. Received: 18 October 1996/Accepted: 31 October 1996     

Relationship Between the B-Ring Hydroxylation Pattern of Condensed Tannins and their Protein-Precipitating Capacity

A series of condensed tannin derivatives with non-, mono-, di- and tri-hydroxylated B-rings were synthesized starting from phloroglucinol and benzaldehyde derivatives. The protein-precipitating capacity of these condensed tannin derivatives showed 1) A condensed tannin with only a 4′-hydroxylated B-ring has almost the same protein-precipitating capacity as that of a condensed tannin with 3′,4′-dihydroxylated or 3′,4′,5′-trihydroxylated B-rings. 2) The complexing ability of phenolic hydroxyl groups in the B-ring are effective in the order of p- > m- > o-positions.