Prediction of color changes in acetaminophen solution using the time–temperature superposition principle

A prediction method for color changes based on the time–temperature superposition principle (TTSP) was developed for acetaminophen solution. Color changes of acetaminophen solution are caused by the degradation of acetaminophen, such as hydrolysis and oxidation. In principle, the TTSP can be applied to only thermal aging. Therefore, the impact of oxidation on the color changes of acetaminophen solution was verified. The results of our experiment suggested that the oxidation products enhanced the color changes in acetaminophen solution. Next, the color changes of acetaminophen solution samples of the same head space volume after accelerated aging at various temperatures were investigated using the Commission Internationale de l’Eclairage (CIE) LAB color space (a*, b*, L* and ΔE*ab), following which the TTSP was adopted to kinetic analysis of the color changes. The apparent activation energies using the time–temperature shift factor of a*, b*, L* and ΔE*ab were calculated as 72.4, 69.2, 72.3 and 70.9 (kJ/mol), respectively, which are similar to the values for acetaminophen hydrolysis reported in the literature. The predicted values of a*, b*, L* and ΔE*ab at 40?°C were obtained by calculation using Arrhenius plots. A comparison between the experimental and predicted values for each color parameter revealed sufficiently high R² values (>0.98), suggesting the high reliability of the prediction. The kinetic analysis using TTSP was successfully applied to predicting the color changes under the controlled oxygen amount at any temperature and for any length of time.     

Fabrication of large-volume microfluidic chamber embedded in glass using three-dimensional femtosecond laser micromachining

We report on fabrication of large-volume, square-shaped microfluidic chamber embedded in glass by scanning a tightly focused femtosecond laser beam inside a porous glass immersed in water. After the hollow structure is created in the porous glass substrate, the fabricated glass sample is post-annealed at 1,050°C during which it can be sintered into a compact glass. By the use of this technique, a 1 mm × 1 mm × 100 μm microchamber connected to four microfluidic channels is created inside the transparent glass substrate, showing that our technique allows for fabrication of not only thin channel structures with arbitrary lengths and configurations, but also hollow structures with infinitely large sizes.     

Particle-based multiple irregular volume rendering on CUDA

In this paper, we describe an improved particle-based volume rendering (PBVR) technique for previewing a large irregular volume dataset using the CUDA architecture. This technique allows for opaque and emissive particles to render translucent volumes without visibility sorting. Our GPU acceleration of PBVR provides the multi-volume rendering feature while remaining compatible with both regular and irregular volumes. We also reduce the memory cost required for storing all sub-pixel values by proposing a pixel repetition technique for a large sub-pixel level. By adjusting the repetition level, we achieved a very smooth level of detail (LOD) control for trading quality for speed. Our work demonstrates a full-detail rendering rate from 5 to 10 fps for irregular volume data with mega-scale cell numbers on an NVIDIA GeForce 8800GTS.     

Solving the irregular strip packing problem via guided local search for overlap minimization

The irregular strip-packing problem (ISP) requires a given set of non-convex polygons to be placed without overlap within a rectangular container having a fixed width and a variable length, which is to be minimized. As a core sub-problem to solve ISP, we consider an overlap minimization problem (OMP) whose objective is to place all polygons into a container with given width and length so that the total amount of overlap between polygons is made as small as possible. We propose to use directional penetration depths to measure the amount of overlap between a pair of polygons, and present an efficient algorithm to find a position with the minimum overlap for each polygon when it is translated in a specified direction. Based on this, we develop a local search algorithm for OMP that translates a polygon in horizontal and vertical directions alternately. Then we incorporate it in our algorithm for OMP, which is a variant of the guided local search algorithm. Computational results show that our algorithm improves the best-known values of some well-known benchmark instances.     

Response analysis for identifying the origin of photo-modulated current contrasts in scanning tunneling microscopic imaging semiconductor surfaces

Inhomogeneities in semiconductor solids can be imaged by two-dimensional mapping of the amplitude of periodically modulated tip current in scanning tunneling microscopy that is induced by illumination of semiconductor samples with a chopped light. It has been shown that it is possible to distinguish between plural origins of the photo-modulated current by analyzing the response properties of the current signal. A judicial choice of the modulation frequency is important for the required contrasts to be obtained.     

Effects of heated seats in vehicles on thermal comfort during the initial warm-up period

Eight subjects participated in a subjective experiment of eight conditions to investigate the effects of heated seats in vehicles on skin temperature, thermal sensation and thermal comfort during the initial warm-up period. The experimental conditions were designed as a combination of air temperature in the test room (5, 10, 15, or 20 °C) and heated seat (on/off). The heated seat was effective for improving thermal comfort during the initial warm-up period when air temperature was lower than 15 °C. Use of heated seats prevented decreases in or increased toe skin temperature. Heated seats also increased foot thermal sensation at 15 and 20 °C. Optimal thermal sensation in contact with the seat was higher when air temperature was lower. Optimal skin temperature in contact with the seat back was higher than that with the seat cushion. Moreover, these optimal skin temperatures were higher when air temperature was lower.     

Formation of Zirconia Solid Solutions Containing Alumina Prepared by New Preparation Method

In the system ZrO₂–Al₂O₃, a new method for preparing ZrO₂ solid solutions from ZrCl₄ and AlCl₃ using hydrazine monohydrate is investigated. c -ZrO₂ solid solutions containing up to ∼40 mol% Al₂O₃ crystallize at low temperatures from amorphous materials. The formation mechanism is discussed from IR spectral data. The values of the lattice parameter α increase linearly from 0.5072 to 0.5105 nm with increasing Al₂O₃ content. At higher temperatures, transformation of the solid solutions proceeds as follows: c ( SS ) → t ( ss ) → t ( ss ) +α-Al₂O₃→ m +α-Al₂O₃. m -ZrO₂–α-Al₂O₃ composite ceramics are fabricated by hot isostatic pressing for 2 h at 1250°C and 196 MPa. Microstructures and mechanical properties are examined, in connection with increasing Al₂O₃ content.     

Agglomeration control of hydroxyapatite nano-crystals grown in phase-separated microenvironments

Materials synthesis processes that require high temperatures consume large quantities of energy that generate an environmental burden. We attempted to synthesize hydroxyapatite (HAp) nano-crystals without firing or melting. “Water in oil” (W/O) emulsions were employed as microreactors for HAp formation. The surfactant-bounded water mediated HAp crystal nucleation, and HAp nano-crystallites were obtained. The obtained particles were aggregates composed of plate-like nano-crystals and monodisperse tiny crystals. Utilization of the W/O emulsions resulted in tunable nucleation frequency and the reactant provision, and yielded HAp nano-crystals with characteristic agglomeration properties.     

Study on high performance ice slurry formed by cooling emulsion in ice storage (discussion on adaptability of emulsion to thermal storage material)

This study focuses on an emulsion as a new thermal storage material for ice storage. Two types of emulsions were formed using an oil–water mixture with a small amount of additive. A silicone, light and lump oils were used. The water contents of the emulsions were 70, 80 and 90%. The additive was an amino group modified silicone oil. No depression of freezing point was observed for the emulsions because of their hydrophobic properties. In order to determine the structure of the emulsions, their electrical resistances were measured. Moreover, components of the liquids separating from the emulsions were analyzed. The results indicated that one emulsion was a W/O type emulsion, while the other was an O/W type. Finally, adaptability of the two emulsions to ice storage was discussed, it was concluded that a high performance ice slurry could be formed by the W/O type emulsion.