Development of a chirped pulse amplification laser with zigzag slab Nd:glass amplifiers dedicated to x-ray laser research

A chirped pulse amplification laser with zigzag slab Nd:glass amplifiers dedicated to x-ray laser research is described. The laser provides a 1.6 ps duration pulse with approximately 7 J energy at a repetition rate of 0.1 Hz. In the power amplifier system, laser light is amplified in a two-step manner: The first step is image-relayed multipass amplification up to approximately 1 J with a 10 mm x 10 mm beam. The second step is double-pass amplification up to >10 J with a 10 mm x 90 mm beam. By using this laser system, the saturated amplification of the Ni-like Ag laser at a wavelength of 13.9 nm has been successfully demonstrated.     

Effects of photo-induced graft polymerization of 2-methacryloyloxyethyl phosphorylcholine on physical properties of cross-linked polyethylene in artificial hip joints

Osteolysis caused by wear particles from polyethylene in the artificial hip joints is a serious issue. We have used photo-induced radical graft polymerization to graft 2-methacryloyloxyethyl phosphorylcholine (MPC) polymer onto the surface of cross-linked polyethylene (CLPE-g-MPC) in order to reduce friction and wear at the bearing surface of the joint. The physical and mechanical properties of CLPE and CLPE-g-MPC were not significantly different, expect that the friction coefficient of untreated CLPE cups was 0.0075, compared with 0.0009 for CLPE-g-MPC cup, an 88% reduction. After 3.0 × 10⁶ cycles in the hip joint simulator test, we could not observe any wear of CLPE-g-MPC cups. We concluded that the advantage of photo-induced radical graft polymerization technique was that the grafted MPC polymer gave a high lubricity only on the surface and has no effect on the bulk properties of the CLPE substrate.     

Structural characterization of glycopeptides by N-terminal protein ladder sequencing

High-sensitivity and high-throughput mass spectrometry (MS) has become an important tool for characterizing glycopeptides. Here, we analyzed synthetic O-linked glycopeptides using matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) MS. First, we applied MALDI-quadrupole ion trap (QIT)-TOF MS, which enables collision-induced dissociation-MSn analysis for fine structural characterization. Subsequent MS/MS of sodium adduct ions selected as precursor ions yielded detailed information about the site of oligosaccharide attachment as well as the carbohydrate and amino acid sequences; however, these MS/MS spectra were very complex. To obtain easily interpretable and simple spectra, we used N-terminal protein ladder sequencing coupled with MALDI-TOF MS. From the extremely simple resulting spectra, we were able to determine the glycosylation sites, amino acid sequences, and oligosaccharide molecular weights of the glycopeptides.     

Burning rates of liquid fuels in fire whirls

This paper presents semi-empirical investigations on the quasi-steady burning rates of laminar and turbulent fire whirls established over liquid fuel pools. The inflow boundary layer above the fuel surface consists of two regions: outer reactive region and inner non-reactive region. Based on the momentum boundary layer solutions with the applications of stagnant film model and Chilton–Colburn analogy, the burning rates are correlated with ambient circulation and pool size for laminar and turbulent fire whirls respectively. It is shown that in general pool fires the mass and heat transfers on the fuel surface are controlled by natural convection, while in fire whirls they are strongly enhanced by forced convection. Fuel evaporation rate in the outer region is relatively larger than that in the inner region. The large proportion of fuel evaporated from the outer region is mainly due to its larger area. The predictions agree well with the data from the present experiments and the literature. Furthermore, the flame height is confirmed to be proportional to the ambient circulation for both laminar and turbulent liquid fire whirls.     

Oxidation of green rust suspensions containing different chromium ion species

The oxidation of hydrosulphate green rust (GR2(SO₄²⁻)) suspension containing different chromium ion species was investigated by X-ray diffraction, X-ray absorption spectroscopy and transmission electron microscopy. The pH, oxidation-reduction potential and amount of dissolved oxygen in aqueous solutions were measured during the reactions. The results show that the addition of Cr(III)₂(SO₄)₃ solution suppresses the transformation of GR2(SO₄²⁻) into iron oxyhydroxides and oxides in aqueous solution, while the addition of Na₂Cr(VI)O₄ solution promotes the transformation of GR2(SO₄²⁻) in which Cr(VI) is reduced to Cr(III); α-FeOOH particles were refined by the addition of the chromium ions.     

Effect of acetic acid content on in situ preparation of epoxy/zirconia hybrid materials

Epoxy/zirconia hybrid materials were synthesized via in situ polymerization of acetic acid-modified zirconium alkoxide. The reactivity of acetic acid-modified zirconium alkoxide changed with the amount of acetic acid added. In the hybrid materials, the phase structure varied between the homogeneous phase and nanophase separation as the reactivity of zirconium alkoxide changed. At the molecular level, the storage modulus in the rubbery region significantly increased and the peak area of tan δ in the glass-transition temperature region decreased with increasing zirconia contents in the hybrid dispersed zirconia. Additionally, the optical properties of the hybrid materials in the homogeneous phase were better than those in the system with nanophase separation.     

Mechanical properties of Al–Si–Cu alloys produced by the continuous casting process with heating process

The mechanical properties of aluminium alloys produced by the continuous cast process and heating process (heat-cast-sample) were investigated, where the aluminium alloys are heated continuously to high temperatures for 1 h immediately following heated mould continuous casting (HMC) and sand gravity casting (SGC). The material strength and ductility of the aluminium alloys were irregularly altered depending on the heating temperature. The mechanical properties decreased when the heating temperature increased to 400 °C and were then recovered when the temperature increased to 520 °C. However, these properties decreased again when heated to more than 540 °C. The mechanical properties of the HMC-heat-cast-sample showed overall higher than those for the SGC-sample. In addition to high tensile strength, high ductility was obtained for the HMC-520 °C samples compared with those for the as-cast-sample. Such changes were found to be directly attributable to the different severity of precipitate; moreover the crystal orientation was unchanged even after the heating process.     

Distributions of density and fission products in the reaction product between irradiated MOX fuel and molten zircaloy-2

Two- and three-dimensional images were obtained by X-ray CT in the reaction product between zircaloy-2 cladding tube and MOX fuel. The gamma-ray intensity distributions in the same specimen were also obtained by gamma-ray measurements of two fission products (Cs-137 and Eu-154) and one neutron-activated nuclide (Co-60). The average values of the fuel density (about 10.5 g/cm³) and the cladding density (about 6.55 g/cm³) were obtained in the metallic phase region by evaluation of the density distributions on two-dimensional X-ray CT images. The distributions of the crushed fuel pellet and the pores were also clearly observed in the three-dimensional X-ray CT images. The following results were found from the gamma-ray measurement. First, Cs-137 was observed in the unreacted fuel region and the pore region in the metallic phase region. Second, Eu-154 was widely distributed to all regions. Finally, Co-60 was confirmed only in the metallic phase region.     

Evaluation and Optimization of Preparative Variables for Controlled-Release Floatable Microspheres Prepared by Poor Solvent Addition Method

The aim of this study was to evaluate and optimize preparative parameters for floatable theophylline microspheres prepared by the emulsion–solvent evaporation method. A three-factor three-level Box–Behnken design was employed using amount of poor solvent, temperature-increase rate and drug loading as independent factors, and percentage floating at 3 h and time required for 50% drug release as dependent variables. Simultaneous optimization of the parameters for maximum buoyancy and desirable drug release was conducted using a partitioned artificial neural network. A microsphere using 27.6% of drug loading, 0.29°C/min of temperature-increase rate, and 1.7 mL of poor solvent was identified for maximizing buoyancy and sustaining drug release.