Influence of Laser Peening on Phase Transformation and Corrosion Resistance of AISI 321 steel

The objective of this study is to investigate the influence of laser peening without coating (LPwC) on austenitic to martensitic (γ → α′) phase transformation and corrosion behavior of austenitic stainless steel AISI 321 in 3.5% NaCl environment. Results indicate that LPwC induces a large compressive residual stresses of nearly ?854 MPa and γ → α′ phase transformation of about 18% (volume fraction). Microstructures of peened surface confirmed the γ → α′ phase transformation and showed no grain refinement. Hardness increased slightly with a case depth of 900 μm. Despite the smaller surface roughness introduced, corrosion resistance improved after peening due to compressive residual stresses.     

Experimental investigation of injection timing on the performance and exhaust emissions of a rubber seed oil blend fuel in constant speed diesel engine

An experimental study is conducted to evaluate the use of rubber seed oil with diesel at a proportion of 20% by volume (RSO20) in a constant speed (1500?rpm) direct injected four-stroke air-cooled single-cylinder compression ignition engine at different injection timings (24°, 27°, 30°, 33° bTDC (before top dead centre)). A series of tests were conducted at various engine load conditions at the rated power of 5.9?kW. The injection pressure was maintained at 200?bar. As a result of investigations, at the full load condition, the brake thermal efficiency of RSO20 at 30° bTDC is high compared with other injection timings and brake energy fuel consumption is increased when advancing injection timing. There is a significant reduction in unburned hydrocarbon emission and carbon monoxide emission, and the oxides of nitrogen emission (NO_x) is increased when advancing the injection timing.     

Effect of CoFe2O4 mole percentage on multiferroic and magnetoelectric properties of Na0.5Bi0.5TiO3/CoFe2O4 particulate composites

Na_0.5Bi_0.5TiO₃ (NBT), CoFe₂O₄ (CFO) as well as particulate composites containing different mole percentages of NBT and CFO were synthesized by the solid-state sintering route and characterized for their ferroelectric and ferrimagnetic hysteresis loops, magnetostriction and magnetoelectric (ME) output. The mole% of CFO was found to influence the ferroelectric and ferrimagnetic hysteresis loops as well as magnetostriction and piezomagnetic coefficients which in turn had a significant effect on the magnetoelectric voltage coefficient. The highest magnetoelectric voltage coefficient (α) of 0.5 mV/cm/Oe was recorded in (65) NBT–(35) CFO composite.     

Targeting Endothelial Connexin37 Reduces Angiogenesis and Decreases Tumor Growth

Connexin37 (Cx37) and Cx40 form intercellular channels between endothelial cells (EC), which contribute to the regulation of the functions of vessels. We previously documented the participation of both Cx in developmental angiogenesis and have further shown that loss of Cx40 decreases the growth of different tumors. Here, we report that loss of Cx37 reduces (1) the in vitro proliferation of primary human EC; (2) the vascularization of subcutaneously implanted matrigel plugs in Cx37−/− mice or in WT using matrigel plugs supplemented with a peptide targeting Cx37 channels; (3) tumor angiogenesis; and (4) the growth of TC-1 and B16 tumors, resulting in a longer mice survival. We further document that Cx37 and Cx40 function in a collaborative manner to promote tumor growth, inasmuch as the injection of a peptide targeting Cx40 into Cx37−/− mice decreased the growth of TC-1 tumors to a larger extent than after loss of Cx37. This loss did not alter vessel perfusion, mural cells coverage and tumor hypoxia compared to tumors grown in WT mice. The data show that Cx37 is relevant for the control of EC proliferation and growth in different tumor models, suggesting that it may be a target, alone or in combination with Cx40, in the development of anti-tumoral treatments.     

Multiple Abiotic Stresses Applied Simultaneously Elicit Distinct Responses in Two Contrasting Rice Cultivars

Rice crops are often subject to multiple abiotic stresses simultaneously in both natural and cultivated environments, resulting in yield reductions beyond those expected from single stress. We report physiological changes after a 4 day exposure to combined drought, salt and extreme temperature treatments, following a 2 day salinity pre-treatment in two rice genotypes—Nipponbare (a paddy rice) and IAC1131 (an upland landrace). Stomata closed after two days of combined stresses, causing intercellular CO2 concentrations and assimilation rates to diminish rapidly. Abscisic acid (ABA) levels increased at least five-fold but did not differ significantly between the genotypes. Tandem Mass Tag isotopic labelling quantitative proteomics revealed 6215 reproducibly identified proteins in mature leaves across the two genotypes and three time points (0, 2 and 4 days of stress). Of these, 987 were differentially expressed due to stress (cf. control plants), including 41 proteins that changed significantly in abundance in all stressed plants. Heat shock proteins, late embryogenesis abundant proteins and photosynthesis-related proteins were consistently responsive to stress in both Nipponbare and IAC1131. Remarkably, even after 2 days of stress there were almost six times fewer proteins differentially expressed in IAC1131 than Nipponbare. This contrast in the translational response to multiple stresses is consistent with the known tolerance of IAC1131 to dryland conditions.     

An electrostatic powder spray process for manufacturing thermoplastic composites

Manufacture of thermoplastic composites is expensive because of the difficulty of impregnating the resin into the fibers. Powder processing shows great promise as an impregnation technique for cost-effective manufacturing. This paper discusses an electrostatic powder spray impregnation technique that uses glass fibers. A geodesic fiber spreader is used to spread the fibers locally in the region of maximum powder deposition. A negative corona electrostatic spray gun is employed to charge and direct the powder for coating both sides of the spread fiber tow. The process has been used to impregnate glass fibers with poly(aryl ether ketone ketone) powder. The effect of the powder mass flow, corona voltage, and fiber tow velocity on powder deposition has been investigated. Particle image velocimetry is utilized to determine particle velocities. Compression molded panels have been produced and tested in three point bending.     

A systematic approach to preliminary polymer process development: modeling and design

A general and complete methodology is presented to facilitate systematic modeling and design of polymer processes during the early development period. To capture and handle the subjective type of uncertainty, embedded in the preliminary process development, fuzzy theories are used as a basis to model and design the process in the presence of ambiguity and vagueness. Physical membership functions are developed for mapping the relation between process variables and the associated fuzzy uncertainties. Based on the qualitative results generated using our previously proposed “linguistic based preliminary design method,” the process modeling can be followed even in the absence of any process governing equations. The modeling is carried out by establishing an appropriate fuzzy reasoning system which provides a specific functional mapping that relates input process variables to one (or more than one) output performance parameter(s). A reduced yet feasible domain is generated by our qualitative design scheme to constrain the process variables. Now, any optimization routine can then be employed to search for a proper process design. We demonstrate the effectiveness of the proposed methodology by its application to a typical compression molding process.     

Scaling the Aspect Ratio of Nanoscale Closely Packed Silicon Vias by MacEtch: Kinetics of Carrier Generation and Mass Transport

Metal‐assisted chemical etching (MacEtch) has shown tremendous success as an anisotropic wet etching method to produce ultrahigh aspect ratio semiconductor nanowire arrays, where a metal mesh pattern serves as the catalyst. However, producing vertical via arrays using MacEtch, which requires a pattern of discrete metal disks as the catalyst, has often been challenging because of the detouring of individual catalyst disks off the vertical path while descending, especially at submicron scales. Here, the realization of ordered, vertical, and high aspect ratio silicon via arrays by MacEtch is reported, with diameters scaled from 900 all the way down to sub‐100 nm. Systematic variation of the diameter and pitch of the metal catalyst pattern and the etching solution composition allows the extraction of a physical model that, for the first time, clearly reveals the roles of the two fundamental kinetic mechanisms in MacEtch, carrier generation and mass transport. Ordered submicron diameter silicon via arrays with record aspect ratio are produced, which can directly impact the through‐silicon‐via technology, high density storage, photonic crystal membrane, and other related applications.     

Modeling and analysis of rapid catalyst aging cycles

The primary mode of deactivation of automotive emission control catalysts is thermal aging, and it is well-known that high-temperature lean aging conditions are particularly detrimental. Since evaluating the long-term durability of automotive catalysts is costly and time-consuming, rapid catalyst aging cycles have been developed to mimic (in a reduced time) the catalyst deactivation under real-world driving conditions. One of the commonly used rapid catalyst aging tests is an exothermal aging cycle, which involves a combination of fuel-rich engine operation and supplemental air injection to generate high-temperature lean conditions within the catalyst bed. In this work, we use the previously developed transient three-way catalyst model to investigate the time evolution of the axial temperature profiles and exhaust air–fuel ratio (A/F) along the catalyst bed during the course of the exothermal rapid aging cycles. We find that the thermal front propagates downstream through the catalyst bed relatively slowly (compared to the concentration front) and this can limit the location within the catalyst bed and duration for high-temperature lean exposure. We also investigate how variations of some of the key system design and operating parameters can affect the extent and duration of high-temperature lean exposure. Finally, a simple analytical expression is developed which allows one to estimate the time it takes for the thermal front to travel through the catalyst bed. This time can be compared with the period of the lean A/F operation during the aging cycle to determine the location and duration of high-temperature lean exposure.     

Turmeric nanofiber-encapsulated natural product formulation act as a phytogenic feed additive—A study in broilers on growth performance,biochemical indices of blood,and E. coli in cecum

A phytogenic feed additive (PFA) formulation was prepared with bioactive molecules—curcuminoids, gingerol, and carvacrol by encapsulating in nanofiber isolated from turmeric spent (turmeric nanofiber, TNF). This formulation was completely characterized by scanning electron microscope, ultra performance liquid chromatography, and gas chromatography and evaluated for its efficacy. PFA-encapsulated TNF (PFA@TNF) considerably increased mean body weight, decreased cholesterol level, mortality rate, and reduced Escherichia coli content of broilers than antibiotic growth promoter (AGP). The depth of crypts in the ileum of broilers was considerably reduced by the inclusion of PFA@TNF in diets compared with the AGP.