Axial vibrations of U-shaped bellows with elastically restrained end conditions

Previous work by Li et al. in the area of axial vibrations of bellows dealt with fixed end conditions. However, it is seen on several occasions that bellow ends are welded to a small pipe spool that has a lumped mass such as a valve or an instrument. Hence, the present paper aims at finding out the effect of elastically restrained ends on the axial natural frequencies. The analysis considers finite stiffness axial restraints on the bellows, i.e. solving the set of equations with non-homogeneous boundary conditions. Two bellow specimens are considered for comparison having the same dimensions as taken by Li in his analysis. The transcendental frequency equation deduced is accurate as the first, second and third mode frequencies computed are in close agreement to the ones obtained by Li.     

An order-specific clustering algorithm for the determination of representative demand curves

Data clustering consists of a group of procedures used to collect similar entries or data points within a set into clusters. No existing clustering technique considers entries sequentially in time. In some cases, it is desirable to generate clusters that represent a segment of a time-ordered data set. For these purposes, an order-specific clustering algorithm is proposed. The proposed algorithm employs representative load curves to describe the clusters it generates. The capabilities of the order-specific clustering algorithm are demonstrated on a case study using electricity demand data for the province of Ontario, Canada. Two different applications of the clustering algorithm on this data set are given to demonstrate the effect of error threshold values on the formation of clusters. An analysis of the error for each of these clustering applications is presented.     

Life cycle of hydroprocessing catalysts and total catalyst management

Hydroprocessing catalysts based on Ni, Co, Mo and W are used in various refinery processing applications where several deactivation mechanisms become of importance (coke formation, active phase sintering, metals deposition, poisoning) in the catalyst's life cycle. The life cycle of commercial hydroprocessing catalysts is very complex and includes the catalyst production, sulfidation, use, oxidative regeneration followed by re-sulfidation and reuse or, if reuse is not possible, recycling or disposal. To understand the changes in catalyst properties taking place during a life cycle, the catalyst quality in the different stages can be best monitored by using advanced analytical techniques. The catalyst's life cycle is further complicated by numerous technical, environmental and organizational issues involved. In principle, different companies can be involved in each of the life cycle steps. Leading catalyst manufacturers, together with specialized firms, offer refineries a total catalyst management concept, starting with the purchase of the fresh catalyst and ending with its final recycling or disposal. Total catalyst management includes a broad range of services, ensuring optimal timing during the change-out process, reliable, smooth and safe operations, minimal downtime and maximum catalyst and unit performance.     

Techno-economic study of different alternatives for biodiesel production

Biodiesel has become an attractive diesel fuel substitute due to its environmental benefits since it can be made from renewable resource. However, the high costs surrounding biodiesel production remains the main problem in making it competitive in the fuel market either as a blend or as a neat fuel. More than 80% of the production cost is associated with the feedstock itself and consequently, efforts are focused on developing technologies capable of using lower-cost feedstocks, such as recycled cooking oils and wastes from animal or vegetable oil processing operations.     

Thermal solution of Kashpir shale in pressurized benzene under supercritical conditions

The results of the thermal solution of oil shale in benzene in a flow unit under supercritical conditions are reported. It was found that the conversion of shale organic matter into liquid products increased by a factor of 2.5 with an increase in the solvent pressure from 5 to 15 MPa.     

Sp3/sp2 character of the carbon and hydrogen configuration in micro- and nanocrystalline diamond

Hot filament and microwave plasma CVD micro- nanocrystalline diamond films are analysed by visible and ultra-violet excitation source Raman spectroscopy. The sample grain size varies from 20 nm to 2 μm. The hydrogen concentration in samples is measured by SIMS and compared to the grain size, and to the ratio of sp² carbon bonds determined by Raman spectroscopy from the 1332 cm^− 1 diamond peak and the sp² 1550 cm^− 1 G band. Hydrogen concentration appears to be proportional to the sp² bonds ratio. The 3000 cm^− 1 CH_x stretching mode band intensity observed on the Raman spectra is decreasing with the G band intensity. Thermal annealing modifies the sp² phase structure and concentration, as hydrogen outdiffuses.     

Influence of a lipid phase on steam jet agglomeration of maltodextrin powders

The contribution of an oil phase to the agglomeration mechanisms of food powders was evaluated. Maltodextrin (DE 10), palm oil stearin and two palm oil oleins (up to 25% dry mass) were used as food models. Granulation runs were carried out in a pilot plant steam jet agglomerator. The powders containing oleins were more cohesive than those with stearin and the presence of oil changed the agglomeration mechanisms. The size increase mechanism of pure maltodextrin powder was controlled by surface plasticization and agglomerates with suitable instant properties were obtained. Small amount of oil degenerated drastically the rate of dispersion in water of the powders and their agglomerates but the average size and the mechanical resistance of the agglomerates increased when the oil content of the powders increased. SEM micrographs of agglomerates indicated that higher lipid content in the powders produced compact granules, favoring sinkability but hindering their disintegration. Agglomeration enhanced considerably the flowability of the particles containing oil. The dispersion behavior of the powders with higher lipid content could be correlated with the Hausner Number. A pre-agglomeration step favored the blend of the more cohesive powders producing larger and more resistant agglomerates.     

Choosing the technology of combined processing of titanium-rare-metal raw materials

The main rules and principles which govern the choice of new variants for chemical technology of combined processing of titanium-rare-metal raw materials are considered. The existing variants of the technology are characterized from the viewpoint of their technological, economical, and ecological efficiency and social importance for a given region. A realistic choice of a technology from a large number of available variants should take into account the entire combination of their advantages and disadvantages The implementation of a rational technological scheme will result in the creation of economically profitable and efficient domestic production satisfying the demands of Russian industry in rare-metal and titanium materials. Directions are noted in which it is expedient to continue studies on designing a rational technology of loparite concentrate or some other concentrate.     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.