Process for cobalt separation and recovery in the presence of nickel from sulphate solutions by Cyanex 272

The present paper deals with the extraction of cobalt from a solution containing cobalt and nickel in a sulphate medium similar to the leach liquor obtained by the dilute sulphuric acid pressure leaching of the Pacific Ocean nodules matte followed by copper extraction. The commercial extractant Cyanex 272 (bis (2, 4, 4-trimethylpentyl) phosphinic acid) is used for this purpose. The leach liquor used for the present study contains Co =1.78 g/L and Ni=16.78 g/L. Before cobalt extraction, impurities, such as copper and iron, are removed from the leach liquor by the precipitation method. Increasing the concentration of Cyanex 272 increased the extraction percentage of cobalt due to the increase of equilibrium pH. Cobalt extraction efficiency of >99.9 % is achieved with 0.20 M Cyanex 272 in two counter-current stages at an aqueous: organic (A:O) phase ratio of 1.5∶1. Complete stripping of cobalt from the loaded organic containing 2.73 g/L Co was carried out at pH 1.4 by a synthetic cobalt spent electrolyte in two stages at an A:O ratio of 1∶2. The enrichment of cobalt during extraction and stripping operations was about 3.5 times. A complete process flowsheet for the separation and recovery of cobalt is presented.     

Partial Oxidation of Methane to Syngas over Calcined Ni–Mg/Al Layered Double Hydroxides

The catalytic partial oxidation of CH₄ to syngas was carried out over an Ni–Mg/Al mixed-oxide catalyst prepared from layered double hydroxide-type precursors. The catalysts were characterized by XRD, TPR, UV-DRS, XRF, BET and CHNS analysis. The effects of the catalyst composition and the calcination temperature on the catalytic performance and the extent of catalyst deactivation were investigated. Ni–Mg/Al oxide catalysts converted CH₄ into syngas efficiently with high selectivity. The catalyst performance was strongly related to the Ni particle size and the calcination temperature. The catalysts that were calcined at higher temperature exhibited a better catalytic performance. In conclusion, the NiAl₂O₄ spinel phase had a positive effect on the stability of the catalyst.     

Enhanced extraction of isoflavones from Korean soybean by ultrasonic wave

The amounts of isoflavones extracted from Korean soybean by various ultrasonic waves were compared using 60% aqueous ethanol solution. The effect on extraction yield of variations in solvent composition, temperature, and extraction time was investigated. The experimental results confirmed that ultrasonic waves are a desirable method to extract isoflavones from Korean soybean. The highest yield of aglycone isoflavones was obtained by ultrasonic waves with a frequency of 20 KHz and an extraction time of 10 min, which produced yields of glycoside and aglycone isoflavones three-fold greater than those by dipping method.     

Torque Transmission Capabilities of Bonded Polygonal Lap Joints for Carbon Fiber Epoxy Composites

Although carbon fiber epoxy composite materials have excellent properties for structures, the joint in composite materials often reduces the efficiency of the composite structure because the joint is often the weakest area in the composite structure.

In this paper, the effects of the adhesive thickness and the adherend surface roughness on the static and fatigue strengths of adhesively-bonded tubular polygonal lap joints have been investigated by experimental methods. The dependencies of the static and fatigue strengths on the stacking sequences of the composite adherends were observed.

From the experimental investigations, it was found that the fatigue strength of the circular adhesively-bounded joints was quite dependent on the surface roughness of the adherends and that polygonal adhesively-bonded joints had better fatigue strength characteristics than circular adhesively-bonded joints.     

Physical characteristics of sweet potato pulp/polycaprolactone blends

Sweet potato pulp (SSP) obtained as a by‐product from starch extraction was blended with polycaprolactone (PCL) to prepare a biodegradable plastic material. In the blends, PCL was used as a reinforcing agent. The SPP/PCL blends were prepared by compression‐molding under high temperature and pressure, at different SPP/PCL ratios, and the mechanical properties of the molded specimens were tested. Matrix structure and thermal properties were measured by using a Fourier transform infrared (FTIR) spectrophotometer, scanning electron microscope (SEM), differential scanning calorimetry (DSC), and thermogravimetric analyzer (TGA). Mechanical properties (tensile and flexural properties) were also measured to find the most suitable ratio in a SSP/PCL blend. During compression molding of the SPP/PCL blends under high pressure and temperature, chemical reaction occurred between SPP and PCL, and thus, thermal stability and mechanical strength of the blends increased and water uptake decreased. Also, by increasing the PCL content in the blend, the matrix in the blend became more homogeneous, and consequently, mechanical strength of the molded specimen increased. At 7/3 or 6/4 weight ratio of SSP/PCL, water uptake of the molded specimen became substantially less than that at 8/2. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 861–866, 2004     

Flaw-Tolerance and R-Curve Behavior of Liquid-Phase-Sintered Silicon Carbides with Different Microstructures

β-SiC powder containing 6 wt% A1₂O₃ and 4 wt% Y₂O₃ as sintering additives was pressureless sintered at 2000°C for 1 h (AYE-SiC) and 3 h (AYP-SiC). AYE-SiC consisted of an equiaxed grain structure and AYP-SiC exhibited a micro-structure with platelike grains as a result of grain growth related to β→α phase transformation during sintering, R -curve behavior and flaw tolerance for these silicon carbides were evaluated by the indentation-strength technique. For comparison, the R -curve behavior of conventional sintered, boron- and carbon-doped SiC (SS-SiC) was evaluated. AYE-SiC and AYP-SiC exhibited rising R -curve behavior with toughening exponents of m = 0.042 and m = 0.135, respectively. AYP-SiC exhibited better flaw tolerance and more sharply rising R -curve behavior than AYE-SiC. The more sharply rising R -curve behavior and the better flaw tolerance of AYP-SiC were attributed mainly to grain bridging of crack faces by platelike grains. Because of the high degree of transgranular fracture, SS-SiC exhibited a flat R -curve despite a microstructural feature with platelike grains.     

Poly(trimethylene terephthalate) nanocomposite fibers comprising different organoclays: Thermomechanical properties and morphology

Poly(trimethylene terephthalate) (PTT) nano composites were synthesized by in situ polymerization at high temperature with two thermally stable organoclays: 1,2‐dimethylhexadecylimidazolium‐montmorillonite (IMD‐MMT) and dodecyltriphenyl phosphonium‐MMT (C₁₂PPh‐MMT). PTT hybrid fibers with various organoclay contents were melt‐spun at various draw ratios (DRs) to produce monofilaments. The thermomechanical properties and morphologies of the PTT hybrid fibers were characterized using differential scanning calorimetry, thermogravimetric analysis, wide‐angle X‐ray diffraction, electron microscopy, and mechanical tensile properties analysis. The nanostructure of the hybrid fibers was observed by both scanning and transmission electron microscopy, which showed that the clay layers were well dispersed into the matrix polymer, although some clusters or agglomerated particles were also detected. Unlike the hybrids containing IMD‐MMT, the clay layers of the C₁₂PPh‐MMT hybrid fiber were more dispersed into the matrix polymer. The thermal stability and tensile properties of the hybrid fibers increased with increasing clay content for DR = 1. However, as DR increased from 1 to 9 the ultimate strength and initial modulus of the hybrid fibers with IMD‐MMT increased slightly whereas those of C₁₂PPh‐MMT hybrid fibers decreased slightly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4535–4545, 2006     

Contraction stress build‐up of anisotropic conductive films (ACFs) for flip‐chip interconnection: Effect of thermal and mechanical properties of ACFs

The important mechanical mechanism for the electrical conduction of anisotropic conductive films (ACFs) is the joint clamping force after the curing and cooling processes of ACFs. In this study, the mechanism of shrinkage and contraction stress and the relationship between these mechanisms and the thermomechanical properties of ACFs were investigated in detail. Both thickness shrinkages and modulus changes of four kinds of ACFs with different thermomechanical properties were experimentally investigated with thermomechanical and dynamic mechanical analysis. Based on the incremental approach to linear elasticity, contraction stresses of ACFs developed along the thickness direction were estimated. Contraction stresses in ACFs were found to be significantly developed by the cooling process from the glass‐transition temperature to room temperature. Moreover, electrical characteristics of ACF contact during the cooling process indicate that the electrical conduction of ACF joint is robustly maintained by substantial contraction stress below T_g. The increasing rate of contraction stresses below T_g was strongly dependent on both thermal expansion coefficient (CTE) and elastic modulus (E) of ACFs. A linear relationship between the experimental increasing rate and E × CTE reveals that the build‐up behavior of contraction stress is closely correlated with the ACF material properties: thermal expansion coefficient, glassy modulus, and T_g. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2634–2641, 2004     

Efective Object Identification and Association by Varying Coverage Through RFID Power Control简

This paper presents an effective power scheduling strategy for energy efficient multiple objects identification and association. The proposed method can be utilized in many heterogeneous surveillance systems with visual sensors and RFID （radio-frequency identification） readers where energy efficiency as well as association rate are critical Multiple objects positions and trajectory estimates are used to decide the power level of RFID readers. Several key parameters including the time windows and the distance separations are defined in the method in order to minimize the effects of RFID coverage uncertainty. The power cost model is defined and incorporated into the method to minimize energy consumption and to maximize association performance. The proposed method computes the power cost using the range of the outermost position for possible single association and group associations at every sampling time. An RFID reader is activated with the proper coverage range when the power cost for the current time is lower than the power cost for the next time sample. The simplicity of the power cost model relieves the problematic combinatorial comparisons in multiple object cases. The performance comparison simulation with the minimum and maximum energy consumption shows that the proposed method achieves fast single associations with less energy consumption. Finally, the realistic comparison simulation with the fixed range RFID readers demonstrates that the proposed method outperforms the fixed ranges in terms of single association rate and energy consumption.     

Preparation of poly(ethylene terephthalate) nanocomposite fibers incorporating a thermally stable organoclay

Summary A series of poly(ethylene terephthalate) (PET) nanocomposites containing organically-modified mica (HB-Mica) were prepared by in-situ interlayer polymerization of dimethyl terephthalate and ethylene glycol. The PET nanocomposites, which contained organoclay loadings of 0 to 2 wt %, were melt-spun to produce monofilaments with various draw ratios. Some of the clay particles appeared well dispersed within the PET matrix, while others were found to form agglomerates with sizes greater than 20 nm. The addition of a small amount of organoclay was sufficient to improve the thermo-mechanical properties of the PET hybrid fibers. Both the thermal stability and the mechanical tensile properties increased with increasing clay content for draw ratios of 1–16.