Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

An optical instrumentation using a sensor with a sensordummyagainst noises on sensor and transmission line

This short paper discusses the method of effectively canceling equal status normal mode noise not only on a sensor line but also on a transmission line of an optical instrument using a sensor with a sensordummy resistance     

High-frequency analysis of the Ellipticus antenna

Efficient numerical solution techniques have been developed and used to examine the electromagnetic fields that can be developed in the working volume of the CW Ellipticus antenna operated at frequencies from 100 kHz to 1 GHz. An exponentially tapered transition section is designed to obtain the desired illumination pattern in the working volume. The input transition section is needed for impedance matching and to drive efficiently the Ellipticus antenna. A parametric study is performed to ascertain the performance of the Ellipticus antenna for frequencies up to 1 GHz     

Microscopic simulation of electronic noise in semiconductormaterials and devices

We present a microscopic interpretation of electronic noise in semiconductor materials and two-terminal devices. The theory is based on Monte Carlo simulations of the carrier motion self-consistently coupled with a Poisson solver. Current and voltage noise operations are applied and their respective representations discussed. As application we consider the cases of homogeneous materials, resistors, n⁺nn ⁺ structures, and Schottky-barrier diodes. Phenomena associated with coupling between fluctuations in carrier velocity and self-consistent electric field are quantitatively investigated for the first time. At increasing applied fields hot-carrier effects are found to be of relevant importance in all the cases considered here. As a general result, noise spectroscopy is found to be a source of valuable information to investigate and characterize transport properties of semiconductor materials and devices     

1/f noise sources

This survey deals with 1/f noise in homogeneous semiconductor samples. A distinction is made between mobility noise and number noise. It is shown that there always is mobility noise with an α value with a magnitude in the order of 10^-4. Damaging the crystal has a strong influence on α, α may increase by orders of magnitude. Some theoretical models are briefly discussed none of them can explain all experimental results. The α values of several semiconductors are given. These values can be used in calculations of 1/f noise in devices     

Metal diffraction gratings as laser power or energy dividers

The authors survey published results on the application of metal diffraction gratings as laser power or energy dividers when the laser beam is split into two approximately equal pans. The normal incidence of laser radiation on metal diffraction gratings of various profiles in the case of three propagating diffraction orders n=0, ±1 is discussed, along with the case of oblique incidence with only two propagating diffraction orders n=0 and n =–1.Translated from Izmeritel'naya Tekhnika, No. 2, pp. 22–26, February, 1994.     

Effects of error variation in means of measurement on reliability parameters in engineering-system monitoring

A method is given for calculating the monitoring reliability parameters (MRP) for an engineering system with allowance for the drift in the measurement error of the means of measurement (MM). The approach is based on introducing a biased MM error distribution into the traditional formulas for the conditional probabilities of spurious and unobserved failure. The bias at the center of the distribution is determined by the systematic error at the given instant. An example is given to illustrate the performance in MRP calculation.Translated from Izmeritel'naya Tekhnika, No. 1, pp. 12–13, January, 1994.     

Effect of pulse time gate on CsI(T1) light output

The mass and charge identification of secondary particles with Z < 4 by a large CsI(T1) scintillation detector is performed using pulse shape analysis and time-of-flight methods. The dependence of the light output on E, A and Z is studied in the energy range of 1–20 MeV/A and special attention is paid to the integration time of the photomultiplier anode signal. It is found that the behaviour of the calibration curves strongly depends on the choice of the integration time interval.