N-Type Field-Effect Transistors Using Multiple Mg-Doped ZnO Nanorods

Nanorod field-effect transistors (FETs) that use multiple Mg-doped ZnO nanorods and a SiO₂ gate insulator were fabricated and characterized. The use of multiple nanorods provides higher on-currents without significant degradation in threshold voltage shift and subthreshold slopes. It has been observed that the on-currents of the multiple ZnO nanorod FETs increase approximately linearly with the number of nanorods, with on-currents of ~1 muA per nanorod and little change in off-current (~4times10^-12). The subthreshold slopes and on-off ratios typically improve as the number of nanorods within the device channel is increased, reflecting good uniformity of properties from nanorod to nanorod. It is expected that Mg dopants contribute to high n-type semiconductor characteristics during ZnO nanorod growth. For comparison, nonintentionally doped ZnO nanorod FETs are fabricated, and show low conductivity to compare with Mg-doped ZnO nanorods. In addition, temperature-dependent current-voltage characteristics of single ZnO nanorod FETs indicate that the activation energy of the drain current is very low (0.05-0.16 eV) at gate voltages both above and below threshold     

Optical properties of Nd-doped Ca3(VO4)2 single crystal fiber

Optical absorption and photoluminescence of Ca₃(VO₄)₂ single crystal grown by a floating-zone technique and containing Nd³⁺ ions were investigated. High absorption coefficients and broadening of most absorption bands are present at 300 K, while substructures in some of the same bands can be evidenced at 12 K. Most features of measured spectra are characteristic of random occupation of more than a single Ca²⁺ site by the Nd³⁺ ion and of distortions provoked by different charge compensation mechanisms involving oxygen vacancies promotion in the crystal lattice. Nd³⁺ optical properties were studied by using the Judd-Ofelt theory to calculate the spectral parameters relevant for laser applications.     

Design and analysis of a plug-in robust compensator: an application to indirect-field-oriented-control induction machine drives

It is well known that the system performance for an indirect-field-oriented-control induction motor drive degrades under the variation of rotor resistance and in the presence of external load torque. In this paper, a plug-in robust compensator for speed and position control enhancement of an indirect-field-oriented-control induction machine drive is developed. In the case where a controller for the induction machine already exists or is in operation with satisfactory nominal tracking performance, this plug-in compensator, designed using the H/sub /spl infin// loop-shaping techniques, can be plugged into the existing controller without affecting the already satisfactory nominal tracking performance of the existing closed-loop system but with the capability to improve the system performance under plant parameter variations and in the presence of external disturbances. Simulation and experimental results are given to validate the proposed plug-in robust compensator.     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

Stabilization of singularly perturbed fuzzy systems

This paper presents some novel results for stabilizing singularly perturbed (SP) nonlinear systems with guaranteed control performance. By using Takagi-Sugeno fuzzy model, we construct the SP fuzzy (SPF) systems. The corresponding fuzzy slow and fast subsystems of the original SPF system are also obtained. Two fuzzy control designs are explored. In the first design method, we propose the composite fuzzy control to stabilize the SPF subsystem with H/sup /spl infin// control performance. Based on the Lyapunov stability theorem, the stability conditions are reduced to the linear matrix inequality (LMI) problem. The composite fuzzy control will stabilize the original SP nonlinear systems for all /spl epsiv//spl isin/(0,/spl epsiv//sup */) and the upper bound /spl epsiv//sup */ can be determined. For the second design method, we present a direct fuzzy control scheme to stabilize the SP nonlinear system with H/sup /spl infin// control performance. By utilizing the Lyapunov stability theorem, the direct fuzzy control can guarantee the stability of the original SP nonlinear systems for a given interval /spl epsiv//spl isin/[/spl epsiv/_,/spl epsiv/~]. The stability conditions are also expressed in the LMIs. Two SP nonlinear systems are adopted to demonstrate the feasibility and effectiveness of the proposed control schemes.     

汽车发动机电机铁芯用钢(ADW2)的研制开发

鞍钢研制开发的汽车发动机启动电机用钢是针对汽车电机铁芯用钢（定、转子）而开发的电机钢类产品。介绍了该产品的研制过程及规格、特点。通过批量试制及装机试验，产品巳满足用户的使用要求。     

导磁不锈钢毛的结构化研究

研制了一种新型的结构化钢毛——胶结钢毛。和传统的普通钢毛相比,胶结钢毛具有很强的结构刚度和很低的钢毛流失量;同时,对高岭土有较高的除铁效率。     

预应力钢-混凝土组合梁的应用与研究

回顾了预应力钢 混凝土组合梁国内外应用与研究历史 ,分析了现有规范及理论的不足 ,并指出了有待解决的问题。     

应用均匀设计法研究安息香缩合工艺

利用均匀设计法通过SPSS10.0计算机软件研究了反应条件对安息香缩合的影响。从而获得优化的工艺条件，与正交试验相比，该法试验次数少。工作效率高，并且便于分析各种因素的影响。     

Kinetics of Zn and Pb evaporation from liquid iron

The evaporation kinetics of Zn and Pb from liquid iron at 1600°C were studied under argon pressure 0.1 to 50 bar in an induction furnace. It was found that the limiting step of evaporation under p_Ar < 1 bar is diffusion in the melt. Diffusion in the gas phase becomes rate-determining with increasing argon pressure. The phase boundary reaction has no effect on the evaporation of Zn and Pb. The evaporation of Zn can evidently be reduced by increasing argon pressure above 1 bar, while the evaporation of Pb is not significantly effected by changes of argon pressure.