25%小偏置碰撞策略及测试评估研究

随着汽车事故的增加,且小重叠碰撞事故死亡率居高不下,小偏置碰撞试验逐渐成为焦点。基于IIHS公布的最新车辆碰撞试验结果,统计超过100余款不同类型的25%小偏置碰撞车辆,建立碰撞转角与碰撞区域的数学模型,将25%小偏置碰撞归结为三种不同的碰撞策略,分别是吸能策略、掠过策略和掠过与吸能策略;并进行试验验证,对三种策略的优缺点进行分析。结果表明,小偏置碰撞试验可运用合理的碰撞策略达到法规要求,对25%小偏置碰撞试验具有一定的参考价值。     

超高效液相色谱-串联质谱法同时检测糕点中6种甜味剂

目的建立超高效液相色谱-串联质谱法同时测定糕点中6种常用合成甜味剂的分析方法。方法选用超纯水作为提取溶剂,涡旋和超声提取后,低温离心,取部分上清液加入正己烷除脂,Waters Atlantis■T3色谱柱、甲醇-5 mmol/L甲酸铵(含0.1%甲酸)作为流动相、亲水亲脂平衡型固相萃取柱HLB(hydrophile-lipophile balance)净化。结果6种甜味剂在质量浓度为10~200 ng/mL的曲线范围内呈良好线性关系,相关系数r均大于0.999,平均加标回收率在85.0%-98.2%之间,相对平均偏差(relative standard deviation,RSD)为1.3%~6.7%。结论该方法具有前处理简单、灵敏度高、检测速度快等优点,适合糖精钠、甜蜜素、三氯蔗糖、阿斯巴甜、阿力甜、纽甜的检测,但不适用于安赛蜜的检测。     

中药桂枝总黄酮的提取工艺研究

优化桂枝总黄酮的提取工艺，建立桂枝的提取和含量测定方法。通过单因素试验，考察提取方法、提取溶剂浓度、提取体积、提取时间对药材总黄酮含量的影响，采用正交试验，优化提取工艺条件，筛选出桂枝总黄酮的最佳提取工艺。总黄酮最佳提取工艺为75%乙醇、料液比1:40、回流提取时间60 min。该方法能有效测定桂枝药材总黄酮的含量，为该药材的质量标准研究提供一定的科学依据。本方法重复性较好、方法稳定、可行。     

床温及SNCR脱硝对CFB锅炉NOx和N2O排放影响的试验研究

为了研究循环流化床（CFB）锅炉燃用无烟煤时床温及选择性非催化还原（SNCR）脱硝对于NO和N2O排放的影响，在1 MW CFB试验装置上开展了试验研究。结果表明:床温由880 ℃提高到970 ℃，NO排放质量浓度由119.5 mg/m3上升到226.0 mg/m3，N2O排放质量浓度由216.0 mg/m3降低到102.2 mg/m3；在氨氮摩尔比（NSR）为0~3.7之间，随着NSR的提高，脱硝效率从0上升到50.72%；进一步提高NSR到5.2，脱硝效率升至53.61%，增加较为缓慢；随着NSR从0提高到1.7，N2O排放质量浓度由84.3 mg/m3上升至118.3 mg/m3，增长较为缓慢；进一步提高NSR至2.0，N2O排放质量浓度上升至187.7 mg/m3，增长速度提高；继续提高NSR至5.2，N2O排放质量浓度上升至381.4 mg/m3；CFB锅炉采用以尿素为还原剂的SNCR脱硝工艺时，单纯通过加大NSR来提高脱硝效率不仅效果有限，过量喷入的还原剂会造成N2O排放量的显著提高。     

Maximum likelihood-based adaptive differential evolution identification algorithm for multivariable systems in the state-space form

Parameter estimation plays an important role in the field of system control. This article is concerned with the parameter estimation methods for multivariable systems in the state-space form. For the sake of solving the identification complexity caused by a large number of parameters in multivariable systems, we decompose the original multivariable system into some subsystems containing fewer parameters and study identification algorithms to estimate the parameters of each subsystem. By taking the maximum likelihood criterion function as the fitness function of the differential evolution algorithm, we present a maximum likelihood-based differential evolution (ML-DE) algorithm for parameter estimation. To improve the parameter estimation accuracy, we introduce the adaptive mutation factor and the adaptive crossover factor into the ML-DE algorithm and propose a maximum likelihood-based adaptive differential evolution algorithm. The simulation study indicates the efficiency of the proposed algorithms.     

基于信号增强的缓慢泄漏检测方法

目前管道泄漏检测方法可有效检测突发泄漏，对于缓慢泄漏则存在检测灵敏度低、定位不准确等问题。基于此，提出了一种基于信号增强的缓慢泄漏检测方法。通过信号压缩（抽取及移位）克服缓慢泄漏压力信号下降平缓的缺点；根据声波信号具有波形尖锐突出、对突发泄漏敏感的优点，通过建立以压力为输入、虚拟声波为输出的声波信号变送器模型，将压力信号转换为声波信号，克服了泄漏压力信号容易被淹没在管道压力波动及背景噪声中的缺点，实现了缓慢泄漏信号的增强；利用临近插值方法重构虚拟声波信号，基于延时互相关分析实现了缓慢泄漏的准确定位。实验结果表明，该方法具有显著的信号增强效果和定位精度，实现了缓慢泄漏的准确检测。     

Nanomaterials for radiotherapeutics-based multimodal synergistic cancer therapy

Over the past decade, numerous studies have attempted to enhance the effectiveness of radiotherapy (external beam radiotherapy and internal radioisotope therapy) for cancer treatment. However, the low radiation absorption coefficient and radiation resistance of tumors remain major critical challenges for radiotherapy in the clinic. With the development of nanomedicine, nanomaterials in combination with radiotherapy offer the possibility to improve the efficiency of radiotherapy in tumors. Nanomaterials act not only as radiosensitizers to enhance radiation energy, but also as nanocarriers to deliver therapeutic units in combating radiation resistance. In this review, we discuss opportunities for a synergistic cancer therapy by combining radiotherapy based on nanomaterials designed for chemotherapy, photodynamic therapy, photothermal therapy, gas therapy, genetic therapy, and immunotherapy. We highlight how nanomaterials can be utilized to amplify antitumor radiation responses and describe cooperative enhancement interactions among these synergistic therapies. Moreover, the potential challenges and future prospects of radio-based nanomedicine to maximize their synergistic efficiency for cancer treatment are identified.

     

NC Assembly在模具型腔加工中的应用

在模具加工刀路编制时,很多用户会将C reo设计模型导入M aster C A M、C im atron等软件中进行加工刀路编制,往往引起很多数据转换的问题。文中采用C reo软件的一个加工模块N C A ssem bly进行无缝衔接,完成刀路编制。并结合一个实例进行了工艺分析,进而实现粗加工和精加工。