Novel amplified fiber-optic recirculating delay line processor

The application of optical amplifiers (OAs) to fiber-optic delay line signal processing is demonstrated. Both erbium-doped fiber amplifiers (EDFAs) and semiconductor optical amplifiers (SOAs) are applicable. Analytical results are presented for both amplified and unamplified fiber-optic recirculating delay lines (AFORDLs and UFORDLs). In the AFORDL an OA is inserted in the fiber loop. It is shown that the active AFORDL structure is capable of realizing all-fiber filters not possible with the passive UFORDL. This result is significant because it shows that the OAs can function beyond just the trivial optical loss compensation to provide extra flexibility not available in passive designs. An AFORDL design is presented which has a pole near +1 and a zero at -1 in the Z-plane resulting in useful characteristics in the magnitude and phase responses. The results suggest that extension of the concept to higher-order filters has the potential to lead to the realization of more complex optical processors     

89-GHz fT room-temperature silicon MOSFETs

The authors report the implementation of deep-submicrometer Si MOSFETs that at room temperature have a unity-current-gain cutoff frequency (f_T) of 89 GHz, for a drain-to-source bias of 1.5 V, a gate-to-source bias of 1 V, a gate oxide thickness of 40 Å, and a channel length of 0.15 μm. The fabrication procedure is mostly conventional, except for the e-beam defined gates. The speed performance is achieved through an intrinsic transit time of only 1.8 ps across the active device region     

A practical SPICE model based on the physics and characteristics of realistic single-electron transistors

A practical model for a single-electron transistor (SET) was developed based on the physical phenomena in realistic Si SETs, and implemented into a conventional circuit simulator. In the proposed model, the SET current calculated by the analytic model is combined with the parasitic MOSFET characteristics, which have been observed in many recently reported SETs formed on Si nanostructures. The SPICE simulation results were compared with the measured characteristics of the Si SETs. In terms of the bias, temperature, and size dependence of the realistic SET characteristics, an extensive comparison leads to good agreement within a reasonable level of accuracy. This result is noticeable in that a single set of model parameters was used, while considering divergent physical phenomena such as the parasitic MOSFET, the Coulomb oscillation phase shift, and the tunneling resistance modulated by the gate bias. When compared to the measured data, the accuracy of the voltage transfer characteristics of a single-electron inverter obtained from the SPICE simulation was within 15%. This new SPICE model can be applied to estimating the realistic performance of a CMOS/SET hybrid circuit or various SET logic architectures.     

ENVIRONMENTAL TOBACCO SMOKE REMOVAL CAPABILITY OF ACTIVATED CARBON

Removal of gaseous and vapor constituents of environmental tobacco smoke (ETS) by activated carbons in a packed bed arrangement was studied under dynamic conditions and was compared with that by silica gel and molecular sieve 13X. ETS is a mixture of sidestream smoke and exhaled mainstream smoke, and it consists of various organic and inorganic compounds, trace heavy metals, and particulate matters. Due to the complex nature of ETS-air mixture, its removal from indoors is a challenging task. For experimentation in a laboratory, the ETS was produced from a specially designed smoking apparatus that simulated the puffng of a cigarette by a person. Air containing ETS was passed through a bed containing about 25 grams of activated carbon at room temperature. The flow rate of air-ETS mixture through the bed was 4000 cm3/min. The relative humidity of the air was 50% and contained about 35 to 40 ppm of hydrocarbons as measured as methane-equivalent. The number of particles in the inlet air stream were in the range of 30,000 to 35,000 particles/cm3. About 60% of hydrocarbons present in ETS were removed at these operating conditions for a period of about 70 hours. Based on 15 adsorption and regeneration cycles, it was noted that the carbon bed did not loose its capacity for ETS significantly as indicated by the BET surface area and water adsorption data. At the beginning of an adsorption cycle, the carbon bed captured a significant number of particles. However, the bed rapidly lost its particle capture effciency as the experiment progressed. The number of particles in the outlet air stream was found to be the same as that of the inlet stream within five minutes.     

Limit of validity of the moisture diffusivity for the study of moisture transfer inside terracotta

In order to know the limit of validity of the concept of hydrical diffusivity, D_W, we tried to validate the Boltzmann's method used to identify it. We show that for a medium strictly satisfying the equation of diffusion, the method gives quite good results with nevertheless some inaccuracies for the extreme values of water contents. For the real studied material, a backed clay, its identification becomes more difficult because of the dispersion of the wetting phenomenon observed for different specimens of the same material. We are showing that the mean behaviour of one sample is near to be the same as the more probable behaviour of all the samples. Otherwise the values of D_W determined for a wetting cannot be used to describe a drying process. It practical interest is then considerably reduced. In order to test the influence of the gas phase pressure effects on the behaviour of the material, we have determined all the parameters necessary to describe, numerically, wetting and drying processes without to resort to D_W. We noticed an overpressure of the gas phase inside the material due to drying. If the gas pressure effects are, numerically, switched off, we cannot notice any influence on water content profiles for this type of material.     

Stabilization of Time-Varying Linear Discrete Interval-Coefficient Control Systems by Phase State Observations

Stabilization of the trajectories of a linear discrete system closed by dynamic feedback under interval uncertainty of the equations of motion and observation is studied. Sufficient conditions of stabilizability are formulated. Results of numerical experiments are given.     

An integrated modelling environment for the embodiment of mechanical systems

The efficient, economical and often elegant transformation from a design schema to an embodied design solution containing real components is essential for the commercial success of a product. More often the ability of the designer to explore an optimum solution is severely frustrated by the analytically intensive and time-consuming aspects of embodying a concept. This paper presents a computer based system-modelling tool that is to be used by designers during the transformation of a concept to an embodied solution particularly to deal with standard components. This environment provides for the representation of conceptual schemas and subsequent embodiment from computer based component selection modules. These selection modules encompass the full range of electronic representations for standard mechanical components. The strategy for representing a mechanical system, its included components and their associated representations is discussed. The process of constructing a system model, specifying the desired performance characteristics and system resolution are also described.