DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

马钢张庄矿高压辊磨机装配工艺研究

针对马钢张庄矿高压辊磨机辊套疲劳断裂严重、对辊精度不能满足生产要求等问题，马钢重机公司根据张庄矿实际生产要求对对辊进行国产化，国产化内容包括辊轴、辊套等零部件的新制以及装配工艺攻关，通过技术研发同时结合实际生产经验，成功对高压辊磨机辊套与辊轴以及辊轴与轴承进行装配，完成了张庄矿高压辊磨机整对对辊的国产化，为该型设备后续生产及优化提供了理论和实践参考依据。     

Zinc doped Fe2O3 for boosting Electrocatalytic Nitrogen Fixation to ammonia under mild conditions

Artificial nitrogen fixation is emerging as a promising approach for synthesis of ammonia at mild conditions. Inspired by biological nitrogen fixation based on bacteria containing iron, zinc doped Fe₂O₃ nanoparticles are proposed as an efficient and earth abundant electrocatalyst for converting N₂ to NH₃. In neutral media, it achieves a maximum Faradaic efficiency (FE) of 10.4% and a large NH₃ yield rate of 15.1 μg h^?1 mg^?1_cat. at ?0.5 V vs. reversible hydrogen electrode. This catalyst also exhibits excellent selectivity and stability. Theoretical calculations suggest the reaction follows the associative enzymatic mechanism and it has a barrier of as low as 0.68 eV.     

氯甲烷在镁修饰的ZSM-5分子筛催化剂上催化转化研究

在镁修饰的ZSM-5分子筛催化剂上,氯甲烷可以被催化转化为烃类产品。分别采用了离子交换和浸渍的方法来修饰ZSM-5分子筛。离子交换的Mg-ZSM-5催化剂和浸渍的Mg/ZSM-5催化剂都可以提高反应产物中的低碳烯烃的选择性,降低烷烃的选择性,并且保持较高的反应活性,但高的浸渍量对反应活性有一定的影响。NH3-TPD的结果表明,浸渍镁的ZSM-5催化剂的强酸中心数目明显减少。镁的修饰对催化剂酸性的影响导致了产物中低碳烯烃的增加。浸渍Mg的ZSM-5催化剂是潜在氯甲烷转化生成低碳烯烃的催化剂。     

稠油微生物开采技术现状及进展

综述了用微生物方法开采稠油的技术现状与进展，论题如下。①概述。②基本方法：异源微生物采油，包括微生物吞吐和微生物驱；本源微生物采油压大港孔店油田的实例。③主要机理，包括产表面活性剂，降解稠油中重质组分及其他。④技术研究，包括机理性、可行性及经济效益研究，列举了国内外6个实例。⑤现场应用，包括国外1个、国内6个实例。⑥该技术的优势及问题。参22。     

铌和钨对γ-TiAl基合金热稳定性的影响

采用光学显微镜(OM)，扫描电镜(SEM)，X射线衍射研究了TiAl—5Nb，TiAl—14．3Nb，TiAl—8Nb—1W，TiAl—12．3Nb-2W四种合金片层组织在1000℃的热稳定性。结果表明，TiAl—12．3Nb-2W合金热稳定性最好，但合金元素对TiAl基合金热稳定性的影响机理还有待进一步的研究。