永州市抗御"碧利斯"台风的实践与思考

受2006年第四号台风“碧利斯”的影响,永州市出现了持续的强降雨过程,部分地区出现了大暴雨,引发了严重的洪涝灾害,成为近年来影响较为严重的一次台风暴雨。永州市在抗御这次台风暴雨过程中,高度警惕,充分准备,周密部署,科学调度,全力以赴抗灾救灾,将灾害损失降到了最低程度,全市没有垮一库一坝,没有因山洪灾害发生人员伤亡。文章总结了永州市的防灾抗灾经验,并针对防御台风暴雨存在的问题,探讨了进一步减轻台风暴雨灾害损失的对策。     

鄂尔多斯盆地中侏罗世直罗—安定期沉积构造特征

中侏罗世直罗—安定期伴随大华北盆地分化瓦解,直罗—安定组除在鄂尔多斯盆地呈整体分布外,在其周邻地区亦有大量零星分布的同期可对比地层。在现今盆地内,直罗组主要为河流相沉积;安定组以干旱气候条件下的河流、湖泊相沉积为主。直罗—安定组的湖相沉积主要位于盆地东南部的古沉积中心部位,其堆积中心位于盆地西部的乌海—鄂托克前旗—平凉一线,堆积中心与沉积中心偏离。直罗组沉积前古构造格局为南高北低、东高西低。直罗—安定期的古地质面貌呈西北高东南低特点,南、北分异表现甚微。结合周邻同期地层岩性、岩相和现今构造单元形成时限等综合分析,认为直罗—安定期原始盆地的边界大致为:西在贺兰山之西,东达吕梁山之东、太行山以西,北抵大青山,南至秦岭。     

微波等离子体化学气相沉积的 a-Si∶H 性能研究

本文着重对微波等离子体化学气相沉积法高速沉积的 a-Si∶H 膜的物理性能进行评价研究.测量了沉积膜的光电性能、暗电导激活能、光禁带宽度、光吸收特性、沉积膜中悬键态密度以及氢含量等,并讨论沉积条件对膜性能的影响.结果表明,在沉积速率高达30～90(?)/s 情况下,膜的光电导(光照强度10~5Lux)与暗电导比值可达10~3～10~5,暗电导率从10~(-3)到10~(-11)((?)cm)~(-1),其激活能在0.23～0.88eV 之间(0～200℃温度范围内),光禁带宽度为1.40～2.20eV,氢含量约为2～20%.     

Mechanical properties-morphology of rolltruded propylene ethylene block copolymers

Commercially available propylene-ethylene (P/E) block copolymers have been processed by the rolltrusion technique. Properties such as tensile modulus, tensile strength and sample clarity are significantly enhanced compared to the original commercial material. The latter is found to be comprised of ethylene globules distributed uniformly or heterogenously throughout the P/E copolymer, depending upon the manufacturing process. In the rolltruded copolymer, the mechanical and morphological properties depend upon the processing temperature and deformation ratio experienced by the workpiece. The chemical composition of the P/E copolymers also plays a significant part in the improvements in properties induced via rolltrusion that may be carried out below or above the melting temperature of the ethylene component of the copolymers. Differential scanning calorimetry thermograms are very useful in assessing transitional behaviour in this respect and may be used to distinguish between different copolymers (processed and original samples). Correlations among some properties and processing conditions are presented and discussed in relation to polymer composition-processing conditions-morphology-property relationships.     

A nonparametric approach to progressive stress accelerated lifetesting

Progressive-stress accelerated life testing in which the stress on an unfailed item increases linearly with test time when the time transformation function is a version of the inverse power law is considered. The approach is nonparametric in that not many assumptions are made about life distribution. A testing pattern is introduced, and it is explained how to draw inferences from progressive stress tests. An estimator of life distribution at the usual stress level is proposed     

Minimum mean-squared error decision-feedback equalization fordigital subscriber line transmission with possibly correlated line codes

The author presents a theory on MMSE (minimum mean-squared error) decision-feedback equalization which augments previously published results by allowing both a correlated symbol sequence and a fractionally spaced DFE (decision-feedback equalizer) forward filter. This theory facilitates calculating the potential DSL (digital subscriber line) transmission performance in cases of correlated line codes, especially for situations where one or both of the DFE filters are infinite in length. The situation of an infinite-length DFE is of interest because it provides information on the limit of MMSE equalization and can thus serve as a benchmark against which the performance of a finite-length DFE may be compared. The author also presents a few numerical examples of the performance of MMSE decision-feedback equalization in DSL transmission at ISDN (integrated services digital network) basic access rates with several well-known line codes     

Computerised trace method for establishing equations for dimensions and tolerances in design and manufacture

A computerised trace method has been developed for determining the relationships of assembly requirements with design dimensions and tolerances of the components in an assembly, and the relationships of design specifications and machining allowance requirements with manufactured dimensions and tolerances of the component in a process plan. This method traces from the proposed components or planned operations only the dimensions and tolerances that affect the given requirement, and therefore the equations for design or for manufacture can be established simultaneously and accurately. Hence it is possible to establish constraints for the optimisation of dimensions and tolerances for design or for manufacture.