机床工具产品色彩造型初探

本文针对我国机床工具产品色彩设计的现状,结合具体实例,对色彩造型的实质做了初步的探讨。分析了色彩造型和色彩装饰两种设计观和实践效果;以色彩与形状关系及作用的论证为引,论述色彩造型的三大功能作用。并提出可供机床工具产品色彩设计参考的具体设计方法和手段。     

某型杀伤枪榴弹引信弹道炸原因分析及再设计思考

通过对某型杀伤枪榴弹引信所发生的三次弹道炸的原因进行分析，提出用延期索替代延期药盘，并对有关机构进行再设计的对策。     

对洪水分级的浅见

洪水的等级划分应考虑流量、水位、防洪能力及灾害等因素,综合这些因素把洪水分成5个等级。1、2级洪水,洪水流量小,水位低,基本无灾;3级洪水,洪水流量较大或水位较高,有一定灾害;4级洪水,为大洪水或高水位,有较大灾害;5级洪水,为特大洪水或高水位,灾情严重。     

气体绝缘封闭电器的高速瞬变过程和现场试验

随着ＧＩＳ的工作电压不断提高和发展，一系列新的现象和问题也同时出现。从国外一些科研，设计，制造部门所研究发表的内容看，大致有隔离开关操作和高速瞬变过程，粒子影响和对干扰定位的技术，元件的监督，现场试验等课题，本文对以上问题加以综合介绍。     

Air bearing design, optimization, stability analysis andverification for sub-25 nm flying

Three sub-25 nm fly height sliders are presented for near contact recording. The designs are geared towards the goal of achieving 10 Gb/in ² areal density. The optimization procedure presented shows promise for facilitating achievement of this goal. The dynamic simulations show the stability of these designs when disturbed from their steady state conditions     

Measurement and modeling of the sidewall threshold voltage ofmesa-isolated SOI MOSFETs

Five-terminal silicon-on-insulator (SOI) MOSFETs have been characterized to determine the threshold voltage at the front, back, and sidewall as a function of the body bias. The threshold voltage shift with the body bias at the front and back interfaces can be explained by the standard bulk body effect equation. However, the threshold voltage shift at the sidewall is smaller than predicted by this equation and saturates at large body biases. This anomalous behavior is explained by two-dimensional charge sharing between the sidewall and the front and back interfaces. An analytical model that accounts for this charge sharing by a simple trapezoidal approximation of the depletion regions and correctly predicts the sidewall threshold voltage shift and its saturation is discussed. The model makes it possible to measure the sidewall threshold even when it is larger than the front threshold voltage     

60m高度处单片露天超高混凝土悬臂墙的设计与施工

通过采用竖向预应力技术 ,解决了 60m高度处单片 8m高悬臂钢筋混凝土墙根部裂缝宽度超过规范限值的问题 ;采用将预应力钢绞线顶端锚固于墙高中段等结构和施工措施 ,控制墙体长细比不超过 3 0 ,减少了由于长细比过大对墙体承载力的不利影响     

科技期刊编辑专业化和学者化是保证期刊学术质量的关键

一般科技期刊刊载的论文内容都具有很强的专业性,这就要求科技期刊编辑必须具有丰富的专业知识和较高的学术水平才能胜任编辑工作.从编辑过程的选题组稿、论文初审、选择审稿专家和编辑加工四个方面对此进行了阐述,指出了提高科技期刊编辑的相关专业知识和学术水平的措施.     

Modeling Power Supply Noise in Delay Testing

Excessive power supply noise during test can cause overkill. This article discusses two models for supply noise in delay testing and their application to test compaction. The proposed noise models avoid complicated power network analysis, making them much faster than existing power noise analysis tools. can cause performance degradation and     

On the behavior of microstructures with multiple length scales

The current study aims to provide fundamental insight into the behavior of microstructures containing grain sizes that span multiple length scales. A commercial 5083 Al alloy was selected as the material of interest to facilitate comparison with recently published data. The materials studied here were prepared via the thermal consolidation of powders that were cryomilled for different times (i.e., 0, 2, 4, and 8 hours). Following consolidation, the resultant microstructure was characterized by an equiaxed grain morphology with a size distribution centered around 200∼300 nm. Dispersed among the 200- to 300-nm grains were coarse-grained regions or ligaments with a grain size ranging from 600 nm to 2 μm. The occurrence of coarse-grained regions is rationalized on the basis of recrystallization or subgrain coarsening, whereas the occurrence of equiaxed fine regions is proposed to be a result of continuous grain growth. Two types of microstructures were selected for study, containing coarse-grained volumes of approximately 28 pct and 43 pct that corresponded to an ultimate tensile strength (UTS) of 566 MPa and 535 MPa, and a fracture strain of 3.2 pct and 3.5 pct, respectively. The observed ductility and the relevant toughening mechanisms were discussed in light of the presence of multiple length scales.