Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

Agility through discipline: a debate

While Beck asserts that agility is only possible through greater discipline on the part of everyone involved, Boehm counters that you don't broaden the definition of "discipline" by rejecting parts of it. Yet, from inside extreme programming, it seems that the only way to achieve the desired results is to view the world in 'both-and" terms instead of "either-or" terms.     

Thermal storage efficiencies of two solar saltless water ponds

A comparative study between two types of solar ponds is presented. The first type has its free surface covered by a thin layer of transparent paraffin oil. The second type is covered by transparent glass floating devices. Each device disposes an air-vacuum chamber. The free water surface between these devices is covered by transparent paraffin oil also. The thermal storage efficiency of each pond is estimated during two time periods: between sunrise and sunset and from midnight to midnight. The calculated efficiency between sunrise and sunset corresponds to the average transmittance–absorptance product. This is estimated using linear regression and also a maximum likelihood identification technique. The behavior of the system was studied by solving numerically the heat transfer equations of the system. Also an ARMAX (AutoRegressivie Moving Average with eXogenous signal) model allowing the assessment of its performance was presented. This efficiency is larger for the first pond during the sunrise to sunset period and smaller when calculated from midnight to midnight. Thus, the first type of pond could be preferred for a use just after the sunset of the same day, while the second for use after one or more days of heat storage.     

Combined time and wavelength multiplexing technique of optical fiber grating sensor arrays using commercial OTDR equipment

The use of a commercial optical time domain reflectometry device for simultaneous wavelength and time domain multiplexing of fiber-optic Bragg grating sensors is proposed and demonstrated. The realization of such systems provides an inexpensive way of interrogating several hundreds of sensors in a single fiber. Strain resolution of 30 /spl mu/m/m over a strain measuring range of 0.5% was obtained.     

One-dimensional diffuser based on a thick layer of dichromated gelatin

A new diffuser capable of scattering light in one direction (one-dimensional diffuser) has been developed and experimentally tested. The diffuser is formed in a thick layer of dichromated gelatin. The scattering indicatrices of the diffuser measured in two mutually perpendicular directions are presented. It is demonstrated that the indicatrix width in one direction is significantly greater than that in the perpendicular direc-tion. However, no zero-order diffraction has been observed. The proposed one-dimensional diffuser exhibits close scattering indicatrices for reading at a wavelength of 0.44 and 0.63 μm.     

Static and pulsed pressures measured using electrically conducting rubbers

A method of measuring static and pulsed pressures using electrically conducting rubber sensors is proposed. The method is based on a change in the volume resistivity of a filled rubber under the action of external pressure. The pressure-induced change in resistance of the rubber sensor is proportional to the applied pressure and can be measured by a bridge circuit. Using this method, it is possible to evaluate the degree of homogeneity of the pressure distribution over a solid surface. This is achieved by distributing rubber sensors over the given surface.     

Copper-zirconium tungstate composites exhibiting low and negative thermal expansion influenced by reinforcement phase transformations

A fully-dense Cu-75 vol pct ZrW₂O₈ metal matrix composite was fabricated by hot isostatic pressing of Cu-coated ZrW₂O₈ particles. A small amount of the high-pressure γ-ZrW₂O₈ phase was created during the cooldown and depressurization following densification; near complete transformation to γ-ZrW₂O₈ was achieved by subsequent cold isostatic pressing. The thermal expansion behavior of the composite between 25°C and 325°C was altered by the cold isostatic pressing treatment, and also depended on the length of time that had passed between thermal cycles. The measured thermal expansion coefficients within specific temperature ranges varied from −6·10⁻⁶ K⁻¹ to far above the thermal expansion coefficient of the copper matrix. The complex temperature-dependent expansion/contraction behavior could be justified by considering the evolution of phase transformations taking place in the ZrW₂O₈ phase, which were observed by in-situ synchrotron X-ray diffraction measurements.     

Study of phase equilibria in the Al - Pd - Re system

Scanning and transmission electron microscopy have been combined with x-ray diffraction to examine the phase equilibria in the Al - Pd - Re system at 1000°C for compositions from 50 to 100 at.% Al, and the corresponding isothermal section has been constructed. The binary monoclinic Al₃ Re phase has been observed for the first time. It is confirmed that there is a stable icosahedral phase in this system. The boundaries to its homogeneity region have been determined and the phase equilibria in which it participates.