Effects of solvent and temperature on the coupling agent/epoxy resin interface

Increased wetting of the coupling agent/epoxy resin interface was observed when γ-glycidoxypropyltrimethoxysilane, polyfunctional aminosilane and γ-aminopropyltriethoxysilane were applied respectively from methyllethylketone, dimethylformamide and water on woven glass cloths which had been cleaned at 300°C. However, when factory-applied coupling agents were burnt off the woven cloths and fresh coupling agents re-applied, it was found that the nature of the factory-applied coupling agent influenced subsequent wetting. Thinner glass fibres showed a greater improvement in wetting rate than thicker fibres in those solvents identified to be good for improved wettability, irrespective of the heat-cleaning temperature.     

Primary hydration of poly(acrylic acid) sodium salts

Summary The equilibrium water contents of linear poly(acrylic acid) sodium salts with different degrees of neutralisation were found to be dependent on temperature and relative humidity. An octahedral model for the primary hydration of poly(acrylic acid) sodium salts (HIRAOKA and YOKOYAMA 1980) was critically evaluated in the light of these findings and an anomaly in the water uptake versus neutralisation curve at approximately 33% neutralisation was explained by the counterion condensation theory. (MANNING 1979).     

Magnetic resonance imaging (MRI) site planning and economics

Site planning and economic forecasting for MRI require careful, individualized analysis of several possible sites. Particular attention should be accorded to the magnetic environment. Realistic estimates of financial feasibility will depend heavily on decisions of regulators and third-party payers.     

K-winner networks.

A special class of mutually inhibitory networks is analyzed, and parameters for reliable K-winner performance are presented. The network dynamics are modeled using interactive activation, and results are compared with the sigmoid model. For equal external inputs, network parameters that select the units with the larger initial activations (the network converges to the nearest stable state) are derived. Conversely, for equal initial activations, networks that select the units with larger external inputs (the network converges to the lowest energy stable state) are derived. When initial activations are mixed with external inputs, anomalous behavior results. These discrepancies are analyzed with several examples. Restrictions on initial states are derived which ensure accurate K-winner performance when unequal external inputs are used.     

Making99Mo in reactors

Conclusions This comparison of two ways of making⁹⁹Mo shows that there is good scope for making it in any area. If there is a thermal reactor having a high flux, one can make⁹⁹Mo from⁹⁸Mo, and in that case, even irradiation in a high flux makes it favorable to use highly enriched⁹⁸Mo and unblocked targets, which raises the specific activity and thus increases the working life in the^99mTc generator.If there is a thermal reactor with low flux or if there is a fast reactor it is best to make⁹⁹Mo from uranium fission products. The target can be highly enriched²³⁵U, which if necessary can be reused, or low-enriched uranium.There are no essential constraints on making⁹⁹Mo, and the production is mainly based on technological tasks.Translated from Atomnaya Énergiya, Vol. 67, No. 2, pp. 104–108, August, 1989.     

Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field