Influence of untreated and novel electron‐beam‐modified surface‐coated silica filler on the thermorheological properties of ethylene–octene copolymer

We developed surface‐modified silica fillers by coating these with an acrylate monomer, trimethylolpropane triacrylate, or a silane coupling agent, triethoxyvinyl silane, followed by electron‐beam irradiation at room temperature. These were incorporated in an ethylene–octene copolymer rubber. Thermorheological studies of the unvulcanized ethylene–octene copolymer and its untreated and modified silica‐filled composites were done with a shear dynamic oscillating rheometer. Modification of the silica filler, especially via the silanization process followed by electron beam treatment, significantly reduced filler–filler networking as revealed from the log–log plots of storage modulus and complex shear viscosity, and its real component. The rheological complexity of the compositions was analyzed from a double logarithmic plot of the storage modulus and loss modulus. The results obtained from the master curves constructed on the basis of the time–temperature superposition principle and the activation energy calculated from the Arrhenius equation for the flow of above these compounds further supported these findings. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2453–2459, 2003     

Anisotropy in mechanical and dynamic properties of composites based on carbon fiber filled thermoplastic elastomeric blends of natural rubber and high density polyethylene

The effects of short carbon fibers on static and dynamic properties of thermoplastic elastomeric blends of natural rubber (NR) and high density polyethylene (HDPE) have been studied. Both mechanical and dynamic properties are dependent on fiber concentration. The fiber aspect ratio ranges from 20 to 30. Adhesion between fiber and matrix is evident from the SEM photomicrographs of the failed composites and from variation of relative damping properties. Fiber orientation occurring during processing causes anisotropy in the physical properties. In composites with longitudinally oriented fibers, tensile failure occurs by both fiber pullout and breakage, while in composites with transversely oriented fibers, matrix failure dominates. The incorporation of fibers into the matrix lowers the tan δ_max value, but no change in glass transition temperature is observed.     

Dynamic mechanical properties of styrene‐butadiene rubber vulcanizate filled with electron beam modified surface‐treated dual‐phase filler

The influence of the electron beam modification of a dual‐phase filler on the dynamic mechanical properties of styrene‐butadiene rubber (SBR) is investigated in the presence and absence of trimethylol propane triacrylate or triethoxysilylpropyltetrasulfide. Electron beam modification of the filler results in reduction of the tan δ at 70°C, a parameter for rolling resistance, and an increase in the tan δ at 0°C, a parameter for wet skid resistance of SBR vulcanizates. These modified fillers give significantly better overall performance in comparison with the control dual‐phase filler. This variation in properties is explained in terms of filler parameters such as the filler structure that leads to rubber occlusion and filler networking. These results are further corroborated using the master curves obtained by the time–temperature superposition principle. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2992–3004, 2003     

Drag reduction characteristics of graft copolymers prepared by the gamma irradiation of poly(oxyethylene) in the presence of acrylic acid

Graft copolymers were prepared by irradiation of poly(oxyethylene), PEO, aqueous solutions in presence of acrylic acid. Chain transfer to PEO controls the graft length, the measured chain transfer constant of the acrylic acid radicals to PEO being 4.11 × 10^?4 at 25°C. The drag reduction characteristics of the graft copolymers were measured in the Reynolds number range 10⁴–10⁵ in a smooth-walled tube, 0.635 cm inside diameter. The drag reduction falls to near zero as the solution pH is lowered to 3, evidence of the formation of a PEO-poly(acrylic acid) coacervate.     

Polyamide-6,6/in situ silica hybrid nanocomposites by sol-gel technique: synthesis, characterization and properties

The organic-inorganic hybrid nanocomposites comprising of poly(iminohexamethyleneiminoadipoyl), better known as Polyamide-6,6 (abbreviated henceforth as PA66), and silica (SiO₂) were synthesized through sol-gel technique at ambient temperature. The inorganic phase was generated in situ by hydrolysis-condensation of tetraethoxysilane (TEOS) in different concentrations, under acid catalysis, in presence of the organic phase, PA66, dissolved in formic acid. Infrared (IR) spectroscopy was used to monitor the microstructural evolution of the silica phase in the PA66 matrix. Wide angle X-ray scattering (WAXS) studies showed that the crystallinity in PA66 phase decreased with increasing silica content. Atomic force microscopy (AFM) of the nanocomposite films revealed the dispersion of SiO₂ particle with dimensions of <100 nm in the form of network as well as linear structure. X-ray silicon mapping further confirmed the homogeneous dispersion of the silica phase in the bulk of the organic phase. The melting peak temperatures slightly decreased compared to neat PA66, while an improvement in thermal stability by about 20 °C was achieved with hybrid nanocomposite films, as indicated by thermogravimetric analysis (TGA). Dynamic mechanical analysis (DMA) exhibited significant improvement in storage modulus (E′) for the hybrid nanocomposites over the control specimen. An increase in Young's modulus and tensile strength of the hybrid films was also observed with an increase in silica content, indicating significant reinforcement of the matrix in the presence of nanoparticles. Some properties of the in situ prepared PA66-silica nanocomposites were compared with those of conventional composites prepared using precipitated silica as the filler by solution casting from formic acid.     

Preparation and properties of styrene–butadiene rubber based nanocomposites: The influence of the structural and processing parameters

Rubber‐based nanocomposites were prepared with octadecyl amine modified sodium montmorillonite clay and styrene–butadiene rubber with different styrene contents (15, 23, and 40%). The solvent used to prepare the nanocomposites, the cure conditions, and the cure system were also varied to determine their effect on the properties of the nanocomposites. All the composites were characterized with X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and transmission electron microscopy (TEM). The XRD studies revealed exfoliation for the modified clay–rubber composites. The TEM photomicrographs showed a uniform distribution of the modified clay in the rubber matrix. The thickness of the particles in the exfoliated composites was around 10–15 nm. Although the FTIR study of the unmodified and modified clays showed extra peaks due to the intercalation of the amine chains into the gallery, the spectra for the rubber–clay nanocomposites were almost the same because of the presence of a very small amount of clay in the rubber matrix. All the modified clay–rubber nanocomposites displayed improved mechanical strength. The styrene content of the rubber had a pronounced effect on the properties of the nanocomposites. With increasing styrene content, the improvement in the properties was greater. Dicumyl peroxide and sulfur cure systems displayed similar strength, but higher elongation and slightly lower modulus values were obtained with the sulfur cure system. The curing of the samples at four different durations at 160°C showed that the cure time affected the properties. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 698–709, 2004     

Measurement of intrinsic rates for homogeneous gas‐phase reactions at high temperatures

A coiled quartz tubular reactor has been designed to measure the intrinsic reaction kinetics for homogeneous reactions at high temperatures up to 1100°C. Actual gas residence times were less than 100 ms. A simple and well‐studied test reaction (i.e., the decomposition of nitrous oxide, N₂O), with published intrinsic kinetics, was used to verify the operation of the experimental reactor. For this system, Peclet numbers (Pe = uL/DL) computed from experimental conversion data were greater than 1000, indicating that the plug flow assumption could be used with this reactor system to determine intrinsic rate expressions with errors of less than 5% for the conditions studied.     

Melt‐processable rubber: Chlorinated waste tire rubber‐filled polyvinyl chloride

Chlorinated ground rubber tire (Cl‐GRT) particles were used as filler in a plasticized polyvinylchloride (PVC) to develop a melt‐processable rubber composition. Physical properties of the Cl‐GRT‐filled PVC compound showed improvement compared to the nonchlorinated counterpart. Interaction between Cl‐GRT and PVC was examined on the basis of results of stress relaxation, dynamic mechanical thermal analysis, and solvent swelling studies. The Cl‐GRT could be loaded upto 40 parts per hundred parts of PVC, and the composition still retains the elastomeric characteristics. The Cl‐GRT‐filled composite was found to be reprocessable like the unfilled PVC compound. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 622–631, 2002; DOI 10.1002/app.10352     

Scalable P2P bot detection system based on network data stream

P2P Botnets are one of the most malevolent threats to the Internet users due to their resiliency against takedown efforts. In this paper, we propose a bot detection system that is capable of detecting stealthy bots in a network. This system treats network traffic as a data stream, segregating the traffic into two parallel streams. The detection is based on failure traffic and communication traffic. The traffic is analyzed during small time window, and the infected hosts are reported immediately. The network administrator can monitor the status of hosts in the network and can take the necessary action before the infected hosts harm the system or can involve in the attacks. Experiments and evaluation of the proposed system on a variety of P2P data transfer applications and P2P botnets have demonstrated high accuracy of detection. The scalability of the proposed system is exhibited through its implementation on Hadoop MapReduce.