汽油喷射稀薄混合气的燃烧

本文研究了汽油喷射发动机稀薄混合气燃烧具有重要意义的空燃比、涡流强度、点火时刻、排气再循环和喷油定时等参数对油耗率和循环波动率的影响，并与化油器供油的发动机作对比分析。结果表明，汽油喷射可燃用更稀薄的混合气，指出在影响汽油喷射燃烧的三个主要因素中，以涡流的影响最大，空燃比次之，喷油定时在上止点前５０°ＣＡ到后１０°ＣＡ之间时对燃烧的影响相对较小。     

进气道和燃烧室形状对火花点火发动机燃烧过程影响的研究

本文针对ＣＡ６１０２发动机燃烧慢、循环变动率偏大等问题，对进气道和燃烧室进行了改进。研究了不同进气道和燃烧结构（六种匹配方案）对燃烧过程和性能的影响，发现涡流比和性能之间无单调的相关关系，与燃烧期之间存在二次抛物线型的逆变相关关系，ＣＡ６１０２发动机合适的涡流比在０．９左右，燃烧室设计因素中火花塞的位置对燃烧过程和性能影响最大，火花塞靠近中心布置方案同原机相比，最低燃油消耗率降低了４．１％，最大扭     

The jet mixing effect on reaction flow in a bluff-body burner

This study investigates the mixing effects of primary and secondary jets on flame stability as fuel/air is injected into a bluff-body burner. A two-dimensional spray combustion model, based upon a SIMPLER method, is used for numerical studies of combusting flow. The influence of the jet-to-air velocity ratio on the recirculation zone behind the bluff body, the center axial velocity and the temperature profiles is studied in detail. The results show that mixing between the two jets is controlled by two vortex eddies on the inside and outside of the bluff-body. With a proper bluff-body blockage ratio, cone angle and jet-to-air velocity ratio a more stable flame can be achieved.     

Stabilization of Discrete-time Fuzzy Systems Via Delta Operators and its Application to Truck–Trailer Model

This paper addresses the problem of robust \(L_2{-}L_\infty \) control in delta domain for a class of Takagi–Sugeno (TS) fuzzy systems with interval time-varying delays and disturbance input. In particular, the system under study involves state time delay, uncertainties and fast sampling period \(\mathcal {T}\). The main aim of this work was to design a \(L_2{-}L_\infty \) controller such that the proposed TS fuzzy system is robustly asymptotically stable with a \(L_2{-}L_\infty \) prescribed performance level \(\gamma >0\). Based on the proper Lyapunov–Krasovskii functional (LKF) involving lower and upper bound of time delay and free-weighting technique, a new set of delay-dependent sufficient conditions in terms of linear matrix inequalities (LMIs) are established for obtaining the required result. The result reveals that the asymptotic stability is achieved quickly when the sampling frequency is high. Finally, a numerical example based on the truck–trailer model is given to demonstrate the effectiveness and potential of the proposed design technique.     

Red photoluminescence BCNO synthesized from graphene oxide nanosheets

In this paper, we demonstrate the conversion of graphene oxide (GO) into boron carbon oxynitride (BCNO) hybrid nanosheets via a reaction with boric acid and urea, during which the boron and nitrogen atoms are incorporated into graphene nanosheets. The experimental results reveal that GO is important for the photoluminescence (PL) BCNO phosphor particles. More importantly, in this system, the prepared BCNO phosphors can be used to prepare the materials needed for red light emitting diodes (LEDs).     

Photonic A/D conversion using low-temperature-grown GaAs MSM switches integrated with Si-CMOS

By linking the unique capabilities of photonic devices with the signal processing power of electronics, photonically sampled analog-to-digital (A/D) conversion systems have demonstrated the potential for superior performance over all-electrical A/D conversion systems. We adopt a photonic A/D conversion scheme using low-temperature (LT)-grown GaAs metal-semiconductor-metal (MSM) photoconductive switches integrated with Si-CMOS A/D converters. The large bandwidth of the LT GaAs switches and the low timing jitter and short width of mode-locked laser pulses are combined to accurately sample input frequencies up to several tens of gigahertz. CMOS A/D converters perform back-end digitization, and time-interleaving is used to increase the total sampling rate of the system. In this paper, we outline the development of this system, from optimization of the LT GaAs material, speed and responsivity measurements of the switches, bandwidth and linearity characterization of the first-stage optoelectronic sample-and-hold, to integration of the switches with CMOS chips. As a final proof-of-principle demonstration, a two-channel system was fabricated with LT GaAs MSM switches flip-chip bonded to CMOS A/D converters. When operated at an aggregate sampling rate of 160 megasamples/s, the prototype system exhibits /spl sim/3.5 effective number of bits (ENOB) of resolution for input signals up to 40 GHz.     

意大利移动市场考察报告

截至2002年4月底,意大利的移动通信用户数已超过5200万,普及率高达88%,用户规模仅次于德国,是欧洲第二大移动通信市场。目前,意大利共有4家GSM移动运营商:TIM,OmnitelVodafone,Wind和Blu,分别占有市场份额的46.7%、34.4%、15.3%和3.6%。意大利的运营商早在1998年就开始了移动互联网业务的市场培育工作,现在,移动互联网业务收入在意大利各运营商的总业务收入中已经占到10%～15%的比例。意大利的3G牌照是通过拍卖的方式颁发,OmnitelVodafone,TIM,Wind,IPSE2000,Wind,和H3G五家运营商获得了3G执照。ReportofStudyTouro     

一种基于紧急程度的自时钟开始时间公平排队分组调度算法

为了克服目前GPS (Generalized Processor Sharing)类调度算法中实时应用分组的排队时延较大且不稳定的局限性,该文提出一种新的分组排队调度算法,该调度算法在计算分组服务标签时添加了一个紧急程度函数,调整了到达分组间的竞争关系,从而可以按照实时性应用的要求来调整到达分组的转发先优级,由此显著降低了实时性应用分组的排队时延和抖动幅度。分析和仿真实验表明,与GPS类其它调度算法相比,该调度算法对于实时应用的分组能提供较低的、更稳定的排队时延保证,同时还继承了GPS类算法的公平性和排队时延有界等特性,而且对系统虚拟时间的跟踪计算更为简捷高效。     

单晶Si材料表面碱织构实验研究

在利用单晶Si材料制备太阳电池的过程中,通常利用碱溶液各向异性腐蚀的特性,在表面形成类似于金字塔的绒面结构,降低太阳电池表面反射,提高太阳电池的转换效率。实验采用固定反应温度以及反应时间,调整NaOH溶液的质量分数和无水乙醇的体积分数,通过测量不同实验条件下样品的表面反射率和观察扫描电镜图像,最终得到较好的单晶Si太阳电池表面织构条件。最后分析NaOH溶液的质量分数和无水乙醇的体积分数对表面织构的影响,同时给出测量表面减反射率结果。该结论对工业化单晶Si太阳电池表面织构的制备具有一定的指导意义。     

La基高k栅介质的研究进展

SiO2作为栅介质已无法满足MOSFET器件高集成度的需求,高k栅介质材料成为当前研究的热点。综述了高k栅介质材料应当满足的各项性能指标和研究意义,总结了La基高k栅介质材料的最新研究进展,以及在改正自身缺点时使用的一些实验方法,指出了有可能成为下一代MOSFET栅介质的几种La基高k材料。La基高k材料的研究为替代SiO2的芯片制造工艺提供优异的候选材料及理论指导,这是一项当务之急且浩大的工程。