Mechanical properties of wollastonite‐reinforced polypropylene composites modified with SEBS and SEBS‐g‐MA elastomers

Mechanical properties of isotactic polypropylene/wollastonite/styrene rubber block copolymers (iPP/wollastonite/SRBC) composites were studied as a function of elastomeric poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) triblock copolymer (SEBS) and SEBS grafted with maleic anhydride (SEBS‐g‐MA) content from 0 to 20 vol%. Microphase morphology was stronger influenced by SRBC elastomers than by different wollastonite types. Higher encapsulation ability of SEBS‐g‐MA than SEBS caused more expressive core‐shell morphology and consequently higher notched impact strength as well as yield parameters, but lower Young's modulus. Higher ductility of the composites with SEBS than with SEBS‐g‐MA has been primarily caused by better miscibility of the polypropylene chains with SEBS molecules. Surface properties of components and adhesion parameters also indicated that adhesion at SEBS‐g‐MA/wollastonite interface, which was stronger than the one at the SEBS/wollastonite interface, influenced higher encapsulation of wollastonite particles by SEBS‐g‐MA. POLYM. ENG. SCI., 47:1873–1880, 2007. © 2007 Society of Plastics Engineers     

Experimental observation of temperature gradients occurring in a single zeolite pellet

An experimental study has been made of temperature profiles incident within a zeolite adsorbent particle in the course of adsorption of n-heptan. Using thermocouple wires 0.1 mm in diameter it has been possible to measure simultaneously the temperatures of the surface and in the centre. It was observed that temperature differences between center of the pellet and ambient stagnant gas may be more than 20°C. The results of this work indicate that the overheating of an adsorbent particle is a very rapid process which is followed by a slow cooling of the hot particle. Experimental data are compared with predictions calculated from the theoretical model.     

Structure Development of NiO–YSZ Oxide Mixtures in Simulated Citrate–Nitrate Combustion Synthesis

Yttria-stabilized zirconia (NiO/YSZ) composites were prepared by the modified citrate–nitrate combustion synthesis. The citrate–nitrate combustion proceeded through several consecutive steps. Evolution of structure in the system and its changes were followed up by thermogravimetry-differential scanning calorimetry, X-ray powder diffraction, extended X-ray absorption fine structure, and high resolution transmission electron microscopy analyses of intermediate products prepared at distinct temperatures that correspond to different stages of the combustion process. It was shown that the crystalline structure developed gradually, first with crystallization of nano-sized NiO particles (400°–700°C), which was followed by crystallization of YSZ (800°–900°C). The final composite material after heat treatment at 1100°C comprised of nano-crystals with an average size of 6.5±2 nm.     

Synthesis, structure and magnetic properties of β-MnO 2 nanorods

We present synthesis, structure and magnetic properties of structurally well-ordered single-crystalline β-MnO₂ nanorods of 50–100 nm diameter and several μm length. Thorough structural characterization shows that the basic β-MnO₂ material is covered by a thin surface layer (∼2.5 nm) of α-Mn₂O₃ phase with a reduced Mn valence that adds its own magnetic signal to the total magnetization of the β-MnO₂ nanorods. The relatively complicated temperature-dependent magnetism of the nanorods can be explained in terms of a superposition of bulk magnetic properties of spatially segregated β-MnO₂ and α-Mn₂O₃ constituent phases and the soft ferromagnetism of the thin interface layer between these two phases.     

Solvent induced crystallization of syndiotactic poly(methyl methacrylate) relation to the formation of polymer aggregates in solution

Polymer Bulletin - Solutions of syndiotactic (s) poly (methyl methacrylate) (PMMA) and samples of solid s-PMMA prepared from these solutions were studied by NMR and infrared (IR) spectroscopy and...     

Negative electrodes for nickel-cadmium accumulators: their properties as determined by impregnation procedure

Sintered negative electrodes for nickel-cadmium secondary cells were studied. Model electrodes prepared by means of three different impregnation methods were evaluated. It was demonstrated that the impregnation procedure may affect properties of active mass and the service life of electrodes in a significant way.     

Polymerization characteristics of a dye of anthraquinone

A technical dye of the anthraquinone type was analyzed by GPC, mass spectroscopy, and elemental analysis. Along with the polymerizable component, N-[4-amino-3-methoxyanthraquinonyl-(1)] methacrylamide (I), it contained a saturated admixture, N-[4-amino-3-methoxyanthraquinonyl-(1)]-2-chloro-2-methylpropionamide (II). The homopolymerization of I was carried out, and admixture II was isolated and characterized. The copolymerization of the dye with styrene and methyl methacrylate was verified, and the retardation effect of II on the polymerization of these monomers was evaluated.     

Scalable Realistic Rendering with Many‐Light Methods

Recent years have seen increasing attention and significant progress in many‐light rendering, a class of methods for efficient computation of global illumination. The many‐light formulation offers a unified mathematical framework for the problem reducing the full lighting transport simulation to the calculation of the direct illumination from many virtual light sources. These methods are unrivaled in their scalability: they are able to produce plausible images in a fraction of a second but also converge to the full solution over time. In this state‐of‐the‐art report, we give an easy‐to‐follow, introductory tutorial of the many‐light theory; provide a comprehensive, unified survey of the topic with a comparison of the main algorithms; discuss limitations regarding materials and light transport phenomena and present a vision to motivate and guide future research. We will cover both the fundamental concepts as well as improvements, extensions and applications of many‐light rendering.