Preparation of superacid of iron-supported zirconia for reaction of butane to isobutane

A highly active superacid of 2 wt% Fe-supported ZrO₂ for the skeletal isomerization of butane to isobutane was obtained by sfexposing Fe₂O₃/ZrO₂ to 1 N H₂SO₄ followed by calcining in air at 700°C for more than 24 h; the Fe₂O₃/ZrO₂ was prepared by impregnating zirconia gel with a solution of Fe(NO₃)₃ followed by drying at 300°C (2 wt% Fe). A much lower activity was observed with the opposite procedure, where the first impregnation was sulfation of the gel, followed by a second impregnation with the iron compound. It was proved from analysis of the sulfur content in the catalysts that residual sulfur species were not related with generation of the superacidic sites. XPS showed the catalyst to be Fe₂O₃ supported on ZrO₂.Superacids by metal oxides, VIII. For previous publications VI and VII in this series see refs. [10,11].     

Chaos in parametric resonance flow at water-mercury interface

In the electrochemical system with liquid-liquid interface, intense local convections by the resonance with potential pulses take place. Therefore, with laser beam scattering, temporal movement of the water-mercury interface was observed. As a result, the scattering efficiency showed non-linear oscillation.

Such non-linear response could be controlled by potential pulse height. As the potential height was increased, new scattering peaks in the oscillation emerged, which was expected of a kind of bifurcation phenomenon. From these results, phase portrait, Poincarè section, correlation dimension of the strange attractor and the largest Lyapunov exponent of the trajectories were obtained. Consequently, it was concluded that all the parameters indicate chaotic behavior of the resonance flow.     

Cationic copolymerization behavior of a bicyclic orthoester having hydroxy group with glycidyl phenyl ether and volume change on their copolymerization

This article describes cationic ring‐opening copolymerization of a bicyclic orthoester having hydroxy group (BOE‐OH) and glycidyl phenyl ether (GPE), and the volume shrinkage behavior during the copolymerization. THF soluble polyethers [poly(BOE‐OH‐co‐GPE)] were obtained by the copolymerizations at 80–180°C, while crosslinked poly(BOE‐OH‐co‐GPE) was obtained by the copolymerizations at 220–250°C. This crosslinking reaction may originate from the dehydration of methylol groups in the side chain of poly(BOE‐OH‐co‐GPE). The volume shrinkage during the cationic copolymerization reduced as the increase of the BOE‐OH feed ratio. By contrast, the volume shrinkage on the crosslinking polymerization was almost independent on the BOE‐OH feed ratio. Poly(BOE‐OH‐co‐GPE)s with higher BOE‐OH composition showed lower thermal weight loss temperature owing to the release of H₂O by dehydration of methylol groups. The BOE‐OH component in the THF soluble poly(BOE‐OH‐co‐GPE)s lowered the glass transition temperature (T_g), while that in the crosslinked poly(BOE‐OH‐co‐GPE) increased the T_g probably because of the higher crosslinking density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1356–1361, 2006     

Balanced corpus of contemporary written Japanese

The balanced corpus of contemporary written Japanese (BCCWJ) is Japan’s first 100 million words balanced corpus. It consists of three subcorpora (publication subcorpus, library subcorpus, and special-purpose subcorpus) and covers a wide range of text registers including books in general, magazines, newspapers, governmental white papers, best-selling books, an internet bulletin-board, a blog, school textbooks, minutes of the national diet, publicity newsletters of local governments, laws, and poetry verses. A random sampling technique is utilized whenever possible in order to maximize the representativeness of the corpus. The corpus is annotated in terms of dual POS analysis, document structure, and bibliographical information. The BCCWJ is currently accessible in three different ways including Chunagon a web-based interface to the dual POS analysis data. Lastly, results of some pilot evaluation of the corpus with respect to the textual diversity are reported. The analyses include POS distribution, word-class distribution, entropy of orthography, sentence length, and variation of the adjective predicate. High textual diversity is observed in all these analyses.     

Lysozyme requires fluctuation of the active site for the manifestation of activity

Mutations around His15 which lie far away from the active site,stimulated glycol chitin activity of lysozyme at physiologicaltemperature. Del-Argl4Hisl5 lysozyme, a mutant lysozyme whoseArgl4 and Hisl5 were deleted together, and has the highest activityamong these mutant lysozymes, had a similar binding abilityto a trimer of N-acetyl-glucosamine, a substrate analogue, relativeto native lysozyme. This suggests that the increased activitywas due to an increased k_cat in the catalysis reaction. TheH-D exchange rate of the N-1 proton in the Trp63 which is locatedin the active site cleft, was enhanced in the Del-Argl4Hisl5lysozyme, while 2-D proton NMR analysis revealed no conformationalchange around Trp63. We conclude that some sort of fluctuationat the active site might be required for the manifestation ofactivity. This theory is supported by the finding that the Del-Argl4Hisl5lysozyme showed a shift in temperature dependency of activityto lower temperatures compared with that of native lysozyme.     

Fractionation and enrichment of CLA isomers by selective esterification with Candida rugosa lipase

A commercial product of CLA contains almost equal amounts of cis-9,trans-11 (c9,t11)-CLA and trans-10,cis-12 (t10,c12)-CLA. We attempted to enrich the two isomers by a two-step selective esterification using Candida rugosa lipase that acted on c9,t11-CLA more strongly than on t10,c12-CLA. An FFA mixture containing CLA isomers was esterified with an equimolar amount of lauryl alcohol in a mixture of 20% water and the lipase. When the esterification of total FA reached 50%, two isomers were fractionated in a good yield: t10,c12-CLA was enriched in FFA, and c9,t11-CLA was recovered in lauryl esters. The FFA were esterified again to enrich t10,c12-CLA. At 27.3% esterification of total FA, the t10,c12-CLA content in FFA increased to 64.8 wt% with 89.3% recovery: The ratio of the content of t10,c12-CLA to that of two isomers was 95.9%. Lauryl esters obtained by the single esterification were employed for enrichment of c9,t11-CLA. After the esters were hydrolyzed, the resulting FFA were esterified again with lauryl alcohol. At 62.0% esterification of total FA, the c9,t11-CLA content in lauryl esters increased to 73.3 wt% with 79.4% recovery: The ratio of the content of c9,t11-CLA to that of two isomers was 95.6%. In a 600-g-scale purification, molecular distillation was effective in separating the reaction mixture into lauryl alcohol, FFA, and lauryl ester fractions.     

Effect of reaction kinetics of polymer electrolyte on the ion‐conductive behavior for poly(oligo oxyethylene methacrylate)–LiTFSI mixtures

The effect of the reaction kinetics on the ionic conductivity for a comblike‐type polyether (MEO) electrolyte with lithium bis(trifluoromethane sulfonyl)imide (LiTFSI) was characterized by DSC, complex impedance measurements, and ¹H pulse NMR spectroscopy. The ionic conductivity of these electrolytes was affected by the reaction condition of the methacrylate monomer and revealed by the glass transition temperature (T_g), spin–spin relaxation time (T₂), steric effects of the terminal groups, and the number of charge carriers indicated by the VTF kinetic parameter. In this system, the electrolytes prepared by the reaction heating rate of 10°C/min of MEO–H and 15°C/min of MEO–CH₃ showed maximum ionic conductivity, σ_i, two to three times higher in magnitude than that of the σ_i of the others at room temperature. As experimental results, the reaction kinetic rate affected the degree of conversion, the ionic conductivity, and the relaxation behaviors of polyether electrolytes. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2149–2156, 2003     

Decomposition of Carbon Dioxide to Carbon with Active Wustite at 300°C

Active wustite (FeδO, with a δ value of 0.98) was prepared by keeping normal wustite (δ value of 0.94) in a N₂ atmosphere at 300°C for 10 min. This reaction is given by (4δ₂–3)Fe_δ1O→(4δ₁–3)Fe_δ2O + (δ₂–δ₁)Fe₃O₄ where δ₁= 0.94 and δ₂= 0.98. The equation indicates that the normal wustite undergoes eutectoid decomposition into active wustite and stoichiometric magnetite (Fe₃O₄). Carbon dioxide (1.013 × 10⁵ Pa) was almost completely (100%) decomposed into carbon (zero valence) by the active wustite at the low temperature of 300°C, which was associated with the transformation of the active wustite into the stoichiometric magnetite. The internal pressure of the reaction cell eventually became a vacuum.     

Electroless copper plating using Fe as a reducing agent

Although the electroless plating method is known to be an effective method for obtaining fine wiring in particular, 1 mol hydrogen gas is generated during 1 mol Cu deposition, and voids are generated in the wiring when electroless Cu plating is applied to fine wiring. To avoid the hydrogen evolution, the possibility of performing electroless Cu plating was confirmed using an inexpensive Fe^II compound as a reducing agent. The bath contains CuSO₄, FeSO₄, NaCl, ethylenediamine, sodium citrate, polyethylene glycol (PEG), and 2,2′-bipyridine. Under optimal conditions, over 1.7 μm of copper deposit with a smooth surface was obtained after 3 h of plating, which did not contain iron as an impurity. The electrical resistivity of the copper film is about 3-4 μΩ cm corresponding to that of electroplated copper films.     

Fabrication of large area diffraction grating using LIGA process

X-ray imaging is a very important technology in the fields of medical, biological, inspection, material science, etc. However, it is not enough to get the clear X-ray imaging with low absorbance. We have produced a diffraction gratings for obtaining high resolution X-ray phase imaging, such as X-ray Talbot interferometer. In this X-ray Talbot interferometer, diffraction gratings were required to have a fine, high accuracy, high aspect ratio structure. Then, we succeeded to fabricate a high aspect ratio diffraction grating with a pitch of 8 μm and small area using a deep X-ray lithography technique. We discuss that the diffraction gratings having a narrow pitch and an large effective area to obtain imaging size of practical use in medical application. If the pitch of diffraction gratings were narrow, it is expected high resolution imaging for X-ray Talbot interferometer. We succeeded and fabricated the diffraction grating with pitch of 5.3 μm, Au height of 28 μm and an effective area of 60 × 60 mm².