The Human Host Defense Ribonucleases 1, 3 and 7 Are Elevated in Patients with Sepsis after Major Surgery—A Pilot Study

Sepsis is the most common cause of death in intensive care units and associated with widespread activation of host innate immunity responses. Ribonucleases (RNases) are important components of the innate immune system, however the role of RNases in sepsis has not been investigated. We evaluated serum levels of RNase 1, 3 and 7 in 20 surgical sepsis patients (Sepsis), nine surgical patients (Surgery) and 10 healthy controls (Healthy). RNase 1 and 3 were elevated in Sepsis compared to Surgery (2.2- and 3.1-fold, respectively; both p < 0.0001) or compared to Healthy (3.0- and 15.5-fold, respectively; both p < 0.0001). RNase 1 showed a high predictive value for the development of more than two organ failures (AUC 0.82, p = 0.01). Patients with renal dysfunction revealed higher RNase 1 levels than without renal dysfunction (p = 0.03). RNase 1 and 3 were higher in respiratory failure than without respiratory failure (p < 0.0001 and p = 0.02, respectively). RNase 7 was not detected in Healthy patients and only in two patients of Surgery, however RNase 7 was detected in 10 of 20 Sepsis patients. RNase 7 was higher in renal or metabolic failure than without failure (p = 0.04 and p = 0.02, respectively). In conclusion, RNase 1, 3 and 7 are secreted into serum under conditions with tissue injury, such as major surgery or sepsis. Thus, RNases might serve as laboratory parameters to diagnose and monitor organ failure in sepsis.     

Reducing energy requirement for drying of beet-pulp: Simulation of energy integration between superheated steam and air drying systems

Beet-pulp dehydration in the sugar industry is a highly energy intensive unit operation. Producing 1?kg of dried beet-pulp requires ～2–3?kg of water to be removed. The cost saving is a real challenge in sugar factory as the current dryers are underperforming (around 3?MJ/kg of water evaporated) because the heat recovery is limited and only a small proportion of dryer exhaust can be reused. The aim of this study was to investigate by simulation the energy efficiency of an independent multistage drying method that combines superheated steam drying (SHSD) and hot air drying (AD). Two case studies awarding the two types of energy coupling (AD then SHSD or SHSD then AD) are presented and compared. An approach of optimization is developed from energy balance. A number of operating parameters of the two drying configurations are investigated using sensitivity analysis. It proves that both cases allow an energy economy around 40% compared to the conventional dryer. Nevertheless, the SHSD-AD plant may present more benefits for a better quality product.     

Co-products of beef processing enhance non-haem iron absorption in an in vitro digestion/caco-2 cell model

Beef processing produces high volumes of protein rich, low value, ‘waste’ co-products such as offal. Beef improves uptake of low bioavailable non-haem iron (found in vegetables, fortificants, supplements) and this effect is dubbed the ‘meat-factor’, although the underlying mechanism is not fully understood. Here, we investigate whether bovine co-products (kidney, lung, heart) not previously studied share this enhancing potential. This was determined by coupled in vitro digestion of co-products and subsequent caco-2 cell ferritin formation (an intracellular iron storage protein). In this study we show that bovine co-products significantly increase caco-2 cells’ response to non-haem iron from infant rice cereal. The presence of these co-products, (kidney, lung and heart), increased relative uptake (by 207.13%, 171.21%, 265.28%, respectively), to a greater extent than beef (30.23%). Our findings present a novel function for co-products of beef processing that may have potential as food ingredients to improve non-haem iron bioavailability, thus adding value.     

Survey of 1012 moldy dwellings by culture fungal analysis: Threshold proposal for asthmatic patient management

Different countries have tried to define guidelines to quantify what levels of fungi are considered as inappropriate for housing. This retrospective study analyzes indoor fungi by cultures of airborne samples from 1012 dwellings. Altogether, 908 patients suffering from rhinitis, conjunctivitis, and asthma were compared to 104 controls free of allergies. Portuguese decree law no 118/2013 (PDL118), ANSES (a French environmental and health agency) recommendations, and health regulations of Besançon University Hospital were applied to determine the rates of non‐conforming dwellings, which were respectively 55.2%, 5.2%, and 19%. Environmental microbiological results and medical data were compared. The whole number of colonies per cubic meter of air was correlated with asthma (P < 0.001) and rhinitis (P = 0.002). Sixty‐seven genera and species were detected in bedrooms. Asthma was correlated to Aspergillus versicolor (P = 0.004) and Cladosporium spp. (P = 0.02). Thresholds of 300 cfu/m³ for A. versicolor or 495 cfu/m³ for Cladosporium spp. are able to discriminate 90% of the asthmatic dwellings. We propose a new protocol to obtain an optimal cost for indoor fungi surveys, excluding surface analyses, and a new guideline to interpret the results based on >1000 cfu/m³ of whole colonies and/or above threshold levels for A. versicolor or Cladosporium spp.     

Smart ultrasonic sensors systems: potential of aluminum nitride thin films for the excitation of the ultrasound at high frequencies

We investigated the potential of the aluminum nitride films to excite ultrasonic waves at frequencies >50?MHz. The deposition process of the aluminum nitride thin film layers on silicon substrates was investigated and optimized regarding their piezoelectric behavior. Large single element transducers were deposited on silicon substrates with aluminum electrodes, under different parameters for the magnetron sputter process, like pressure and bias voltage. Special test setup and a measuring station were created to characterize the sensors. Acoustical measurements were carried out in pulse echo mode up to 500?MHz and the values of piezoelectric charge constant (d₃₃) were determined. As a result, two parameter sets were found for the sputtering process to obtain an excellent piezoelectric charge constant of about 7.2?pC/N maximum. Then the sputtering process with these parameters was used to deposit sensors on various substrate materials and with different electrode sizes.