真空制盐蒸发结晶器的设计与实践

真空蒸发制盐外热式强制逆循环轴向出料蒸发结晶器，经多个厂家生产应用实践证明是成功的，具有生命力的。这种新型结构，作为一项新技术新设备应加强研究，总结提高，推广应用。不断完善。文章从流体力学、结晶机理角度要求，到具体工程设计参数和材质选用。论述了该罐的特点。     

Optimal diagonal precoder for multiantenna communication systems

In this paper, we examine a multiantenna single-user wireless communication system fitted with a QR-based successive cancellation receiver (QR receiver). Initially, our consideration is confined to uncoded binary phase shift keying (BPSK) signals transmitted through independent and identically distributed (IID) Rayleigh fading channels and to the design of an optimum precoder for the transmitter. For minimum feeding back of the channel state information (CSI) to the transmitter from the receiver, we stipulate the precoder to be in the form of a power loading square diagonal matrix. We proceed to develop the theory for the design of this diagonal matrix based on the minimization of the lower bound of the average bit error rate (BER) of transmission. The design obtained provides substantially lower error rates than most of other existing schemes under the same environment. The corresponding gain in signal-to-noise ratio (SNR) can be several decibels. To further improve the performance, we extend the design to include an optimal detection order of the received bits using an iterative approach. This iterative process proves to have fast convergence and results in a design providing significant SNR gain. We also propose a subchannel dropping scheme for cases in which SNR is low, and when the minimum BER precoder is equipped with this scheme, its average performance can be substantially superior to the Vertical Bell Laboratories Layered Space-Time (V-BLAST) detection. We extend our design of the optimum precoder to quadrature amplitude modulation (QAM) modulation scheme and similar performance gain has been observed.     

Frequency shift keyed narrowband interference rejection: optimal exponential weighting factor for the RLS algorithm

Cochannel narrowband interference can limit the performance of direct sequence spread spectrum (DSSS) and high frequency (HF) systems. Narrowband interference (NBI) can be single tone, chirped or frequency shift keyed (FSK) in nature and numerous techniques for its removal have been proposed. Linear adaptive prediction filters based on autoregressive modelling have been suggested owing to their ability to perform in a non-stationary environment. In the FSK narrowband interference case, adaptive filters are susceptible to excess residual errors owing to instantaneous frequency step changes and the finite convergence time required for the filter to adapt to a new interference frequency. The signal degradation owing to this type of interference becomes greater in high SNR regimes and has been found to be a function of the frequency parameters of the FSK interference signal. The paper discusses the convergence and frequency tracking properties of the recursive least squares (RLS) adaptive lattice filter using a posteriori estimation errors in the presence of FSK narrowband interference. An optimal exponential weighting factor that balances convergence time and steady state error is derived for this case of NBI. Results are compared to those of a previously proposed fast converging minimum frequency error (FCMFE) RLS lattice filter.     

Studies on the microstructure of the black-glazed bowl sherds excavated from the Jian kiln site of ancient China

The Jian kiln, located in present-day Jianyang county of Fujian province, mainly produced black-glazed tea bowls. Jian tea bowl was used as a utensil for tea tasting and was greatly appreciated by emperor Huizong of the Northern Song dynasty. The black glaze of Jian bowl was sometimes marked with streaks or spots, usually called “hare's fur” or “oil spot”, which are the crystalline markings of iron oxide precipitated during firing in the dragon kiln. In this study, black-glazed Jian bowl sherds excavated from the late Northern Song strata of Luhuaping and Daluhoumen Jian kiln sites were adopted as test samples. Based on the physico-chemical foundation for the formation of glaze microstructure, the correlation among composition, microstructure, and visual appearance has been investigated by means of energy-dispersive X-ray fluorescence, X-ray diffraction, and field emission electron microscopy. For the first time, the study provides realizing proofs for two kinds of microstructural forming mechanics.     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

One-to-Many and Many-to-One Optical Chaos Communications Using Semiconductor Lasers

A theoretical construction of one-to-many (OTM) and many-to-one (MTO) chaos synchronization communications using semiconductor lasers is presented. One center laser provides strong injections (strong link) to other side lasers, and the side lasers also provide weak injections (weak link) to the center one. Simulation results show that the side lasers synchronize with the center laser through injection-locking. In addition, messages transmitted via the strong links or the weak links experience strong chaos pass filtering, enabling us to realize OTM and MTO communications.     

Estimation for the number of components in a mixture model using stepwise split-and-merge EM algorithm

The main difficulty with EM algorithm for mixture model concerns the number of components, say g. This is the question of model selection, and the EM algorithm itself could not estimate g. On the contrary, the algorithm requires g to be specified before the remaining parameters can be estimated. To solve this problem, a new algorithm, which is called stepwise split-and-merge EM (SSMEM) algorithm, is proposed. The SSMEM algorithm alternately splits and merges components, estimating g and other parameters of components simultaneously. Also, two novel criteria are introduced to efficiently select the components for split or merge. Experimental results on simulated and real data demonstrate the effectivity of the proposed algorithm.     

Application of piece‐wise linear weight functions for 2D 8‐node quadrilateral element in contact problems

The present study is a continuation of our previous work with the aim to reduce problems caused by standard higher order elements in contact problems. The difficulties can be attributed to the inherent property of the Galerkin method which gives uneven distributions of nodal forces resulting in oscillating contact pressures. The proposed remedy is use of piece‐wise linear weight functions. The methods to establish stiffness and/or mass matrix for 8‐node quadrilateral element in 2D are presented, i.e. the condensing and direct procedures. The energy and nodal displacement error norms are also checked to establish the convergence ratio. Interpretation of calculated contact pressures is discussed. Two new 2D 8‐node quadrilateral elements, QUAD8C and QUAD8D, are derived and tested in many examples, which show their good performance in contact problems. Copyright © 2004 John Wiley & Sons, Ltd.