聚氨酯／聚苯乙烯互穿聚合物网络的结构与性能研究

通过改变组分比研究了PU/PS IPN结构与性能变化的规律。结果表明,在PU/PS为70/30时,电镜照片上呈现精细的细胞结构,相区尽寸缩小,网络间互穿程度最高,且溶胀度最低。热力学性能也同时出现最佳值,     

The effect of vacuum evaporation plating on phase structure and electrochemical properties of AB5–5 mass% LaMg3 composite alloy

In this paper, Cu, Al and Ni were plated on the AB₅–5 mass% LaMg₃ composite hydrogen storage alloy using a vacuum evaporation plating method. The phase structure and the electrochemical properties were investigated. The X-ray diffraction (XRD) analysis shows that the phase structure is not changed obviously after the plating Cu, Al and Ni on the composites. The electrochemical tests show that maximum discharge capacity, high rate dischargeability (HRD), dischargeability at low temperature and cyclic stability was improved by vacuum evaporation plating Cu, Al and Ni. Maximum of discharge capacity of the AB₅–5 mass% LaMg₃ composite alloy plating Ni can reach 351 mAh/g, which is 3.5% higher than that of the untreated. HRD at I_d = 1200 mA/g of the composite alloy plating Cu is 45.0% of that at 60 mA/g, which is 20.4% higher than the untreated. Discharge capacity of the composite alloy plating Cu at low temperature 233 K is 205 mAh/g, which is 57.3% of that at 298 K, and it is much higher than 36.8% of the untreated composites. The discharge capacity retention of the composite alloy plating Al after 200 cycles is 7.8% higher than the untreated.     

Catalytic characteristics of various rubber-reinforcing carbon blacks in decomposition of methane for hydrogen production

Carbon black has recently been reported to act as an effective catalyst for methane decomposition and to exhibit stable catalytic behavior despite carbon deposition, and thus it can be used for CO₂-free production of hydrogen from natural gas. In this work, various carbon blacks with different primary particle size were investigated with respect to methane decomposition under atmospheric pressure from 1123 to 1223 K. Catalytic characteristics, such as activity, activation energy and reaction order, were investigated and compared. It was observed that with decreasing primary particle size (or increasing specific surface area), the specific activity increased and the activation energy decreased. The reaction orders for various pelletized, rubber-reinforcing carbon blacks were 0.6–0.7, about the same regardless of the primary particle size, while they were near 1 for fluffy carbon blacks. Fluffy carbon black showed higher activity and activation energy than the pelletized carbon black of the same primary particle size. Changes of the surface morphology during carbon deposition were observed by TEM. Variations of the number of active sites were discussed in regard of the primary particle size, carbon deposition and binder. The presence of different types of active sites was also suggested.     

水热法制备纳米尖晶石型NiFe_2O_4及表征

分别采用水热法、共沉淀法合成了纳米尖晶石型铁氧体—NiFe2O4晶体,对两种方法所合成的样品进行了比较,分析了不同合成方法的优缺点,确定水热法为比较适宜的合成该类复合氧化物的方法,该法合成的NiFe2O4晶体的平均粒径仅为15.9nm,且粒度分布十分均匀。此外,通过对实验结果的测定与分析探讨了影响水热制备的几种可能的因素,确定了水热合成的适宜的沉淀剂为NaOH溶液,水热合成适宜的温度为200℃。     

聚合物多元醇产品质量的影响因素与控制

从内在和外在质量两个方面，简要论述了影响聚合物多元醇(POP)产品质量的因素和控制产品质量的措施。     

Oxidative stability of soybean oil fatty acid methyl esters by oil stability index (OSI)

Biodiesel, an alternative diesel fuel derived from transesterification of vegetable oils or animal fats, is composed of saturated and unsaturated long-chain FA alkyl esters. During long-term storage, oxidation caused by contact with air (autoxidation) presents a legitimate concern with respect to monitoring and maintaining fuel quality. Extensive oxidative degradation may compromise quality by adversely affecting kinematic viscosity, acid value, or PV. This work examines the oil stability index (OSI) as a parameter for monitoring the oxidative stability of soybean oil FAME (SME). SME samples from five separate sources and with varying storage and handling histories were analyzed for OSI at 60°C using an oxidative stability instrument. Results showed that OSI may be used to measure relative oxidative stability of SME samples as well as to differentiate between samples from different producers. Although addition of α-tocopherol or TBHQ increased OSI, responses to these antioxidants varied with respect to SME sample. Variations in response to added antioxidant were attributed to aging and other effects that may have caused oxidative degradation in samples prior to acquisition for this study. Results showed that OSI was more sensitive than iodine value in detecting the effects of oxidative degradation in its early stages when monitoring SME during storage.     

Viscoelastic properties of phenolphthalein poly(ether ketone)

Stress relaxation and dynamic mechanical behavior of phenolphthalein poly(ether ketone) (PEK-C) have been investigated. Using Ferry's reduction method, the master curve was obtained. From the experimental results, we found that the WLF equation is not appropriate in the lower-temperature range (T < T_g). The relaxation spectrum was calculated according to the first approximation method proposed by Schwarzl and Staverman. In addition to the α-transition region, a second transition zone is revealed at low temperature. This transition is probably due to a restricted motion of its main chain. © 1995 John Wiley & Sons, Inc.     

Viscoelastic Behavior, Thermodynamic Compatibility, and Phase Equilibria in Block Copolymer-Based Pressure-Sensitive Adhesives

The viscoelastic behavior, thermodynamic compatibility, and phase equilibria in block copolymer-based pressure-sensitive adhesives were investigated. The block copolymers investigated were: (1) polystyrene-block-polybutadiene-block-polystyrene (SBS) copolymer (KRATON® D-1102, Shell Development Company) and (2) polystyrene-block-polyisoprene-block-polystyrene (SIS) copolymer (KRATON® D-1107, Shell Development Company). The tackifying resins investigated were: (1) WINGTACK® 86 (Goodyear Tire & Rubber Company) and (2) PICCOTAC® 95BHT (Hercules Inc.). Samples of various compositions were prepared by a solution-casting method with toluene as solvent. Measurements of dynamic storage modulus (G'), dynamic loss modulus (G'), and loss tangent (tan δ) were taken, using a Rheometrics Mechanical Spectrometer. It was found that: (1) both WINGTACK 86 and PICCOTAC 95BHT were equally effective in decreasing the plateau modulus (G^O_N), and increasing the glass transition temperature (T_g) of the polyisoprene midblock of KRATON 1107; and (2) WINGTACK 86 was very effective in decreasing the G^O_N and increasing the T_g of the polybutadiene midblock of KRATON 1102, whereas PICCOTAC 95BHT was not. The observed difference between WINGTACK 86 and PICCOTAC 95BHT in decreasing the G^O_N and increasing the T_g of the polybutadiene midblock of KRATON 1102, whereas PICCOTAC 95BHT was not. The observed difference between WINGTACK 86 and PICCOTAC 95BHT in decreasing the G^O_N and increasing the T_g of the polybutadiene midblock of KRATON 1102 (perhaps to SBS block copolymers in general) is explained by the values of the interaction parameter for WINGTACK 86 and KRATON 1102, and for PICCOTAC 95BHT and KRATON 1102. The interaction parameter was determined, using the piezoelectric quartz sorption method. Phase diagrams were constructed for the four block copolymer/tackifying resin systems investigated, using information obtained from both dynamic viscoelastic measurements and optical microscopy. It was found that when mixed with KRATON 1102, PICCOTAC 95BHT formed separate domains whereas WINGTACK 86 did not over the range of concentrations and temperatures investigated. This confirms the evidence obtained from two other independent experimental techniques, namely, dynamic viscoelastic measurements and the piezo-electric sorption method. We have concluded from the present study that PICCOTAC 95BHT is not as an effective tackifying resin as WINGTACK 86, when each is mixed with KRATON 1102. It is pointed out further that information on the order-disorder transition temperature T_r, which was determined from a rheological technique proposed by us, is valuable in determining optimal processing conditions for block copolymer-based pressure-sensitive adhesives.     

铬渣-水泥体系的性能及Cr(Ⅵ)渗出的控制研究

本文探讨了铬渣的胶凝活性，研究了不同掺量铬渣对水泥浆体性能的影响。同时，通过矿渣微粉的掺入，探讨了矿粉对铬渣一水泥体系性能的影响厦其对其Cr（Ⅵ）浸出的控制作用。结果表明，铬渣具有良好的胶凝活性，矿渣微粉的复合掺入对Cr（Ⅵ）的浸出有良好的控制作用。