Failure analysis of unidirectional polymeric matrix composites with two serial pin loaded-holes

The objective of this study is to investigate the effects of geometrical and physical parameters on failure modes and failure loads in unidirectional polymeric matrix composites with two serial pin loaded holes, analytically and experimentally. It is assumed that all of unidirectional fibers in the laminate lie in one direction while loaded by a load p ₀ at infinity, parallel to the direction of the fibers. To derive equilibrium equations based on a Shear-Lag theory, a rectangular arrangement of fibers is considered and with the proper use of boundary and boundness conditions, stress and displacement fields are computed within the laminate, along with the surrounding pinholes. Finally by using the Hashin criterion failure modes and failure loads are estimated. To validate analytical results based on shear-lag theory, an experimental program is carried out. A very good agreement is observed between two procedures. Based on results, in small sizes of two pins, the dominant failure mode is bearing and with the increasing of hole sizes, failure modes are changed to tension and shear modes.     

Framework Model for Asset Maintenance Management

This paper presents the development of a generic framework for asset maintenance management. The framework has been presented in the form of an IDEF0 process model. The process model served to illustrate the interaction and dependencies among a diverse set of knowledge areas. In this framework, outputs from one management process become inputs to another in a subsequent hierarchy. The structure of the framework model exhibited the characteristics of flexibility and robustness. Updates in knowledge can be accommodated within the framework through incorporating new management processes and/or activities, as well as establishing new sequencing logic for these processes and/or activities. In a supporting effort to the development of the framework model, the writers have objectively reviewed the general capabilities of three commercially available software applications that are known within the asset management (AM) industry. These three applications, while encompassing a wide selection of capabilities, represent a typical selection of information technology (IT) tools and techniques that are widely used in strategic AM practices. The objective of this review is to study the operational characteristics and functionalities, and to assess the capability of software interoperability, of a representative sample of IT tools known within the AM industry.     

Cross-sectional comparison of production functions for US manufacturing industries: Some evidence on the urban productivity

This study attempts to show that the production function for a given industry associated with urban areas yields a greater output than that associated with rural areas for a given vector of inputs. For purposes of estimation and hypothesis testing, the production function is of the Cobb-Douglas form with three inputs.Empirical estimates are based on cross-sectional data from the census of manufacturing for each manufacturing industry at the two-digit level of the standard industrial classification. From the data, two subsamples—“urban” and “rural”—are created to obtain separate estimates of the parameters of the production function.The empirical results indicate that for 12 of the 19 industries studied, there is no significant difference between the urban and rural production functions, and, for the remaining 7 industries, the results are not conclusive but do suggest that output elasticities of some factors are greater for urban areas than for rural areas.     

Microstructural and electrical properties of varistors prepared from coated ZnO nanopowders

This paper describes a solution-based technique for fabrication of varistor grade composite nanopowders. The method consists of coating major varistor dopants on the surface of the ZnO nanoparticles. As a result, a homogenous mixture of dopants and ZnO nanoparticles will be achieved. TEM results indicated that a composite layer of dopants with the average particle size of 9 nm on the surface of ZnO nanoparticles has been successfully prepared. Sintering of the coated powders was performed in temperatures as low as 850 °C and final specimens with average particle size of 900 nm and density of 98.5% were achieved. In comparison to conventional mixing, varistors prepared from coated nanopowders exhibited superior electrical properties and microstructure homogeneity. The improvement of electrical properties can be attributed to small grain size, homogenous distribution of dopants and elimination of large Bi-Pockets. In addition, the processing route of schottky barrier formation is quite different from what is generally considered as the method of barrier formation in ZnO grain boundaries.     

Bed collapse dynamics of fluidized beds of nano-powder

Bed collapse experiments have been carried out in fluidized beds of agglomerated nano-powders possessing high void fractions. Transient responses for the local pressure-drop as well as the gas velocity during the collapse were recorded. From the local pressure transient data, occurrences of key events of the collapse dynamics were identified. The first event is the zero pressure-drop condition soon after the flow interruption while the second is the global minimum on the pressure-drop profile that marks the end of the first stage of the bed collapse characterized by fast bed transients. The second stage is a relatively slow process, which ends with the onset of the zero pressure-drop condition again (third event) that reflects particles becoming stationary, thus signaling the completion of the collapse dynamics. The time of the first stage of the collapse is found to vary linearly with the initial fluidization velocity at which the collapse experiment was initiated whereas the total collapse time shows a rather weak dependence on the fluidization velocity. On the other hand, the velocity transients during the collapse follow first-order time lag that can be accurately modeled using a single time constant irrespective of the initial fluidization velocity.     

Outcome among patients with acute renal failure needing continuous renal replacement therapy: A single center study

Outcome of acute renal failure (ARF) and use of continuous renal replacement therapy (CRRT) have shown a consistently high mortality. (1) Evaluate the short-term patient survival. (2) Evaluate dialysis-free survival. (3) Evaluate risk factors associated with overall survival and the continued need for intermittent dialysis. We identified adults (≥18 years) needing CRRT, treated in the critical care units of Froedtert Medical and Lutheran Hospital from January 1, 2003 till December 31, 2005. Patients were divided into two major groups needing CRRT, end stage renal disease (ESRD) (chronic dialysis) and non-ESRD with ARF. Continuous renal replacement therapy was performed with an average of 2 L replacement fluid exchanges/h. Sigma stat software was used for analysis. Comparison was done for noncontinuous variables by chi-square and t test for categorical and continuous variables, respectively. A total of 110 (ESRD 24/non-ESRD 86) patients received CRRT during study period. Over all in-hospital mortality among non-ESRD patients was 63% vs. 46% for ESRD. Among non-ESRD patients who survived, 47% needed intermittent hemodialysis on intensive care unit discharge and 28% continued to need hemodialysis at last follow-up. Among non-ESRD patients alive at discharge, those who were dialysis dependent on last follow-up were older (64.5) than those who did not require dialysis on last follow-up (58.4) P=0.347. Non-ESRD patients who died were in the hospital for an average of 17.5 days compared with 29 days for those who were discharged from the hospital. Patients with ARF needing CRRT have high in-hospital mortality. A significant percentage of patients remained dialysis dependant on last follow-up.     

Evaluation of an ultrasonic acid digestion procedure for total heavy metals determination in environmental and biological samples

In this study, a sample preparation method based on ultrasonic assisted acid digestion (UAD) has been evaluated for total heavy metals (Cd, Cr, Ni and Pb) determination in different environmental (soil, sediment and sewage sludge), and biological (fish muscles, vegetables and grains) samples, using electrothermal atomic absorption spectrometry (ETAAS). The investigated parameters influencing UAD such as presonication time, sonication time, temperature of ultrasonic bath, and different acid mixtures were fully optimized, whereas power was maintained constant at 100% of nominal power of ultrasonic bath. Six different sets of above parameters were applied on six certified reference materials (CRMs) having different matrices. The accuracy of the method was also tested by comparing the results with those obtained from conventional hot plate assisted acid digestion method on same CRMs. Analytical results for HMs by both methods showed no significant difference at 95% confidence limit (p<0.05). Recoveries of HMs ranging from 96.2% to 102% and 96.3% to 98.6% were obtained from biological and environmental samples, respectively. The average relative standard deviation of UAD method varied between 3.5% and 8.2%, depending on the analyte.     

Behavior of square concrete columns reinforced with Prefabricated Cage System

Behavior of normal strength concrete columns reinforced with a new reinforcement, termed Prefabricated Cage System (PCS) is investigated. A total of 16 small-scale PCS and rebar reinforced column specimens were constructed and tested under monotonic axial displacement. The experimental results indicate that the overall behavior of rebar and PCS reinforced specimens are comparable prior to achieving the peak column load. In general, PCS specimens are more ductile and absorb more energy than similar rebar specimens after the peak load is reached. The effect of different parameters, such as the steel tube thickness, number of longitudinal reinforcements, transverse steel spacing, and crossties on the specimens’ strength and deformation capacity are investigated. A confined concrete model is proposed and used to predict the load–displacement response. The theoretical load–displacement relations obtained from the proposed model are compared with those obtained from the Mander et al. (J Struct Eng 114(8):1804–1826, 1988) confinement model.     

A platform for electrochemical sensing of biomolecules based on Europia/reduced graphene oxide nanocomposite

This study aimed at preparing and evaluating the europium oxide–reduced graphene oxide (rGO) composites. Inorganic nanoparticles anchored onto rGO sheets through a facile sonochemical method. The resultant products were characterized by FT-IR, XRD, SEM. Their activity in biomolecules’ analysis were examined by cyclic voltammetry. The rectified electrodes revealed an incredibly electroactive manner. The obtained progress provided excellent materials for scrutiny of biomolecules. The linear relationship was used in the region of 100–1500 µM ascorbic acid (AA), 50–600 µM dopamine (DA), and 10–700 µM uric acid (UA), between current intensities and concentrations. The detection restrictions (LOD) (S/N?=?3) decreased to 8 µM, 1.1 µM and 0.085 µM for AA, DA and UA respectively by differential pulse voltammetry (DPV).     

A Comparison of Mamdani and Sugeno Fuzzy Based Packet Scheduler for MANET with a Realistic Wireless Propagation Model

 The mobile nature of the nodes in a wireless mobile ad-hoc network (MANET) and the error prone link connectivity between nodes pose many challenges. These include frequent route changes, high packet loss, etc. Such problems increase the end-toend delay and decrease the throughput. This paper proposes two adaptive priority packet scheduling algorithms for MANET based on Mamdani and Sugeno fuzzy inference system. The fuzzy systems consist of three input variables: data rate, signal-to-noise ratio (SNR) and queue size. The fuzzy decision system has been optimised to improve its efficiency. Both fuzzy systems were verified using the Matlab fuzzy toolbox and the performance of both algorithms were evaluated using the riverbed modeler (formally known as OPNET modeler). The results were compared to an existing fuzzy scheduler under various network loads, for constant-bit-rate (CBR) and variable-bit-rate (VBR) traffic. The measuring metrics which form the basis for performance evaluation are end-to-end delay, throughput and packet delivery ratio. The proposed Mamdani and Sugeno scheduler perform better than the existing scheduler for CBR traffic. The end-to-end delay for Mamdani and Sugeno scheduler was reduced by an average of 52% and 54%, respectively. The performance of the throughput and packet delivery ratio for CBR traffic are very similar to the existing scheduler because of the characteristic of the traffic. The network was also at full capacity. The proposed schedulers also showed a better performance for VBR traffic. The end-to-end delay was reduced by an average of 38% and 52%, respectively. Both the throughput and packet delivery ratio (PDR) increased by an average of 53% and 47%, respectively. The Mamdani scheduler is more computationally complex than the Sugeno scheduler, even though they both showed similar network performance. Thus, the Sugeno scheduler is more suitable for real-time applications.