Queue length‐based load balancing in data center networks

Traffic load balancing in data centers is an important requirement. Traffic dynamics and possibilities of changes in the topology (e.g., failures and asymmetries) make load balancing a challenging task. Existing end‐host–based schemes either employ the predominantly used ECN or combine it with RTT to get congestion information of paths. Both congestion signals, ECN and RTT, have limitations; ECN only tells whether the queue length is above or below a threshold value but does not inform about the extent of congestion; similarly, RTT in data center networks is on the scale of up to few hundreds of microseconds, and current data center operating systems lack fine‐grained microsecond‐level timers. Therefore, there is a need of a new congestion signal which should give accurate information of congestion along the path. Furthermore, in end‐host–based schemes, detecting asymmetries in the topology is challenging due to the inability to accurately measure RTT on the scale of microseconds. This paper presents QLLB, an end‐host–based, queue length–based load balancing scheme. QLLB employs a new queue length–based congestion signal that gives an exact measure of congestion along the paths. Furthermore, QLLB uses relative‐RTT to detect asymmetries in the topology. QLLB is implemented in ns‐3 and compared with ECMP, CONGA, and Hermes. The results show that QLLB significantly improves performance of short flows over the other schemes and performs within acceptable level, of CONGA and Hermes, for long flows. In addition, QLLB effectively detects asymmetric paths and performs better than Hermes under high loads.     

SCM: Secure and accountable TLS certificate management

In classical public‐key infrastructure (PKI), the certificate authorities (CAs) are fully trusted, and the security of the PKI relies on the trustworthiness of the CAs. However, recent failures and compromises of CAs showed that if a CA is corrupted, fake certificates may be issued, and the security of clients will be at risk. As emerging solutions, blockchain‐ and log‐based PKI proposals potentially solved the shortcomings of the PKI, in particular, eliminating the weakest link security and providing a rapid remedy to CAs' problems. Nevertheless, log‐based PKIs are still exposed to split‐world attacks if the attacker is capable of presenting two distinct signed versions of the log to the targeted victim(s), while the blockchain‐based PKIs have scaling and high‐cost issues to be overcome. To address these problems, this paper presents a secure and accountable transport layer security (TLS) certificate management (SCM), which is a next‐generation PKI framework. It combines the two emerging architectures, introducing novel mechanisms, and makes CAs and log servers accountable to domain owners. In SCM, CA‐signed domain certificates are stored in log servers, while the management of CAs and log servers is handed over to a group of domain owners, which is conducted on the blockchain platform. Different from existing blockchain‐based PKI proposals, SCM decreases the storage cost of blockchain from several hundreds of GB to only hundreds of megabytes. Finally, we analyze the security and performance of SCM and compare SCM with previous blockchain‐ and log‐based PKI schemes.     

A Distributed and Elastic Application Processing Model for Mobile Cloud Computing

The latest developments in mobile computing technology have increased the computing capabilities of smart mobile devices (SMDs). However, SMDs are still constrained by low bandwidth, processing potential, storage capacity, and battery lifetime. To overcome these problems, the rich resources and powerful computational cloud is tapped for enabling intensive applications on SMDs. In Mobile Cloud Computing (MCC), application processing services of computational clouds are leveraged for alleviating resource limitations in SMDs. The particular deficiency of distributed architecture and runtime partitioning of the elastic mobile application are the challenging aspects of current offloading models. To address these issues of traditional models for computational offloading in MCC, this paper proposes a novel distributed and elastic applications processing (DEAP) model for intensive applications in MCC. We present an analytical model to evaluate the proposed DEAP model, and test a prototype application in the real MCC environment to demonstrate the usefulness of DEAP model. Computational offloading using the DEAP model minimizes resources utilization on SMD in the distributed processing of intensive mobile applications. Evaluation indicates a reduction of 74.6% in the overhead of runtime application partitioning and a 66.6% reduction in the CPU utilization for the execution of the application on SMD.

     

A computationally efficient selected mapping technique for reducing PAPR of OFDM

In orthogonal frequency division multiplexing (OFDM) system, high value of peak-to-average power ratio (PAPR) is an operational problem that may cause non-linear distortion resulting in high bit error rate. Selected mapping (SLM) is a well known technique that shows good PAPR reduction capability but inflicts added computational overhead. In this paper, using Riemann sequence based SLM method, we applied reverse searching technique to find out low PAPR yielding phase sequences with significant reduction in computational complexity. Additionally, we explored side-information free transmission that achieves higher throughput but sacrifices PAPR reduction. Finally, to overcome this loss in PAPR reduction, we proposed application of Square-rooting companding technique over the output OFDM transmitted signal. Simulation results show that the proposed method is able to compensate the sacrifice in PAPR and achieved PAPR reduction of 8.9 dB with very low computational overhead.     

用空间电荷限制电流法测定n型掺杂的BPhen的电子迁移率

摘 要 用空间电荷限制电流（SCLC）法测定了不同厚度（50-300nm）的Liq掺杂BPhen的电子迁移率。实验结果表明在33wt％Liq掺杂的BPhen中,当厚度达到150nm以后电子迁移率接近于体材料的迁移率。对于300nm厚的掺杂的BPhen,测定的电子迁移率约为5.4×10-3 cm2/Vs （电场强度为0.3MV/cm时）,比本征BPhen的迁移率（3.4×10-4 cm2/Vs）高约一个数量级,而且其迁移率基本上不依赖于电场。同时还对掺杂的BPhen为有机电致发光器件（OLED）的典型厚度时的电子迁移率进行了测定。     

Impact of high-κ dielectric and metal nanoparticles in simultaneous enhancement of programming speed and retention time of nano-flash memory

A methodology to simulate memory structures with metal nanocrystal islands embedded as floating gate in a high-κ dielectric material for simultaneous enhancement of programming speed and retention time is presented. The computational concept is based on a model for charge transport in nano-scaled structures presented earlier, where quantum mechanical tunneling is defined through the wave impedance that is analogous to the transmission line theory. The effects of substrate-tunnel dielectric conduction band offset and metal work function on the tunneling current that determines the programming speed and retention time is demonstrated. Simulation results confirm that a high-κ dielectric material can increase programming current due to its lower conduction band offset with the substrate and also can be effectively integrated with suitable embedded metal nanocrystals having high work function for efficient data retention. A nano-memory cell designed with silver (Ag) nanocrystals embedded in Al₂O₃ has been compared with similar structure consisting of Si nanocrystals in SiO₂ to validate the concept.     

Piezoelectric Sensors Operating at Very High Temperatures and in Extreme Environments Made of Flexible Ultrawide-Bandgap Single-Crystalline AlN Thin Films

Extreme environments are often faced in energy, transportation, aerospace, and defense applications and pose a technical challenge in sensing. Piezoelectric sensor based on single-crystalline AlN transducers is developed to address this challenge. The pressure sensor shows high sensitivities of 0.4–0.5 mV per psi up to 900 °C and output voltages from 73.3 to 143.2 mV for input gas pressure range of 50 to 200 psi at 800 °C. The sensitivity and output voltage also exhibit the dependence on temperature due to two origins. A decrease in elastic modulus (Young's modulus) of the diaphragm slightly enhances the sensitivity and the generation of free carriers degrades the voltage output beyond 800 °C, which also matches with theoretical estimation. The performance characteristics of the sensor are also compared with polycrystalline AlN and single-crystalline GaN thin films to investigate the importance of single crystallinity on the piezoelectric effect and bandgap energy-related free carrier generation in piezoelectric devices for high-temperature operation. The operation of the sensor at 900 °C is amongst the highest for pressure sensors and the inherent properties of AlN including chemical and thermal stability and radiation resistance indicate this approach offers a new solution for sensing in extreme environments.     

Semi-Supervised Deep Learning for Multi-Tissue Segmentation from Multi-Contrast MRI

Journal of Signal Processing Systems - Segmentation of thigh tissues (muscle, fat, inter-muscular adipose tissue (IMAT), bone, and bone marrow) from magnetic resonance imaging (MRI) scans is useful...     

A Hybrid Reconfigurability Structure and Improved Gain Characteristics for a Novel 5G Monopole Antenna for Future Mobile Communication

Wireless Personal Communications - Mobile edge computation (MEC) is a potential technology to reduce the energy consumption and task execution delay for tackling computation-intensive tasks on...